

Lped
Highly customizable low-power electronic playing dice
- Size
- 14 × 14 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 28
- Nets
- 37
- Pads
- 111
- Tracks, vias
- 220, 56
- Pours
- 42
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Jun 2025
- Updated
- 22 Oct 2025
Overview
Lped is an open-source printed circuit board by b1u3-22, from the b1u3-22/LPED repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 14 × 14 mm with 28 parts on 37 nets, routed with 220 tracks and 56 vias.
It is built around the 2450FM07B0037T and FXLS8974CFR3. Its parts include 9 capacitors, 7 connectors, 3 resistors, 2 ICs and 2 diodes. It belongs with the nRF52 and nRF5x boards of this library.
Main components
22450FM07B0037T
SMD-4P,0.5x1mm0.8dB Low Pass SMD-4P,0.5x1mm RF Filters ROHSJohanson DielectricsRF FiltersFXLS8974CFR3
DFN-10(2x2)-40℃~+105℃ 1.71V~3.6V 12bit 600nA Accelerometer Motion event detection、Synchronization and timestamp SPI、I2C X,Y,Z ±16g DFN-10(2x2) Accelerometers ROHSNXP SemiconductorsAccelerometers
README
README.mdLPED
Highly customizable Low-power Electronic Playing Dice
This project started as a bachelors thesis, the original repository can be found here
Features
- Separate charging station for charging the dice via pogo-pins
- Changing the dice shape with custom sleeves
- The dice can be configured to support any shape with up to 60 sides
- Up to 10 profiles can be saved onboard
Hardware
- The dice uses a nRF52810 microcontroller with FXLS8974CF accelerometer
- Instead of battery it uses hybrid super-capacitor with 20 F capacity that provides up to 8 hours of game time with charging time of 15 minutes
- The 3D models of the charging dock have been optimized for 3D printing and they do not require any supports
- However, one heat inserts and 4 magnets (6x6x2mm) are necessary for the assembly
Firmware
- The dice transmits the landed numbers via BLE broadcast advertisement
- To ensure they get to the client application, they are sent multiple times with unique identifier
- For configuration it is necessary to connect to the dice
- It provides all the necessary parameters via characteristics in custom GATT service
- It saves the whole configuration in the FLASH memory of the dice, making it independent on the used client application
- Each side can have its own physical position on the dice and its own number, making it possible to create dice with custom non-standard shapes
Project structure
/hardware- schematics, 3D models and PCB design files for dice, charger and programming adapter- The schematics and PCB designs were made in KiCad
- The printable models were made in FreeCAD
/firmware- Zephyr firmware running on the dice
Versioning info
- Repository uses
major.minorformatmajoris incremented with each major hardware revision or significant firmware update that causes the implementation to be incompatible with previous versionminoris used for firmware fixes and patches that don't affect backwards compatibility
- PCBs have their own version code on them that follows standard
major.minorformatmajoris used for drastic changes to the boards, such as MCU swap or change of pinoutminoris used for hardware fixes and patches
Parts
28| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0u1 | Capacitor_SMD:C_0402_1005Metric | C4, C5 |
| 2 | 12pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 2k1 | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | LED | Diode_SMD:D_0805_2012Metric | D1, D2 |
| 1 | 100p | Capacitor_SMD:C_0402_1005Metric | C6 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10u | Inductor_SMD:L_0603_1608Metric | L3 |
| 1 | 15n | Inductor_SMD:L_0402_1005Metric | L4 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 1u | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 20F | Capacitor_THT:C_Radial_D8.0mm_H11.5mm_P3.50mm | C3 |
| 1 | 2450FM07B0037 | RF_Filter:FIL_2450FM07D0034T | F1 |
| 1 | 32MHz | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D2.0mm | J4 |
| 1 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C9 |
| 1 | BLE Antenna | Chip_Antenna:XDCR_2450AT42E010BE | AE1 |
| 1 | DOCK_CONN | TestPoint:TestPoint_Pad_D2.0mm | J5 |
| 1 | DOCK_LED | TestPoint:TestPoint_Pad_D2.0mm | J6 |
| 1 | FXLS8974CF | Package_DFN_QFN:DFN-10_2x2mm_P0.4mm | U2 |
| 1 | GND | TestPoint:TestPoint_Pad_2.0x2.0mm | J7 |
| 1 | SWDCLK | TestPoint:TestPoint_Pad_D2.0mm | J2 |
| 1 | SWDIO | TestPoint:TestPoint_Pad_D2.0mm | J3 |
| 1 | nRF52833_QDxx | Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm | U1 |
| 1 | ~{RESET} | TestPoint:TestPoint_Pad_D2.0mm | J1 |
More from b1u3-22/LPED
2- 2 layers35.4 × 16 mm

- 2 layers48 × 15 mm

Similar boards
- 4 layers91.4 × 54.6 mm

FRDM MCXx Shield V1.3
EmielV2002/FRDM_MCXx_SensHat
A hat with sensors and actuators for the FRDM-MCXA153 and FRDM-MCXN947 development boards made by NXP.
114 parts2MIT - 2 layers38.1 × 38.1 mm

- 4 layers

- 4 layers85 × 25 mm

- 4 layers25.1 × 34 mm

Pe42543 breakout
loxodes/vna
Under development open hardware microwave vector network analyzer
28 parts205 - 4 layers35.1 × 25.3 mm

T41-si5351A B GM Oscillator daughterboard
DRWJSCHMIDT/T41
This is the repository for the officially released V10, V11, and V12 versions of the T41 Software Defined Transceiver hardware and kits.
28 parts66 - 4 layers38 × 25 mm

- 4 layers30 × 20 mm

Swd switch
alvarop/debugotron
Debugotron is a collection of debugging/automation tools I've wanted in the past but didn't have access to. Currently, the tools include:
28 parts52BSD-3-Clause
Questions
How big is the Lped PCB?
It measures 14 × 14 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Lped use?
28 parts, built around the 2450FM07B0037T and FXLS8974CFR3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Lped KiCad files?
From the b1u3-22/LPED repository on GitHub, at the commit this page was made from: the board is hardware/lped/schematics/lped.kicad_pcb and its schematic hardware/lped/schematics/accelerometer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Lped design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).