
SevenSegmentModule
atomic14/supersise-seven-segment
The code, schematics and PCB layout are offered here without any support. It's fun project but it's also a learning experience.

The code, schematics and PCB layout are offered here without any support. It's fun project but it's also a learning experience.
SevenSegmentClockV2 is an open-source printed circuit board by atomic14, from the atomic14/supersise-seven-segment repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 281.9 × 90.4 mm with 100 parts on 125 nets, routed with 617 tracks and 103 vias.
It is built around the TC4469CPD, TPIC6595N and IRF640N. Its parts include 61 resistors, 14 ICs, 8 capacitors, 4 diodes and 1 transistor.
The code, schematics and PCB layout are offered here without any support. It's fun project but it's also a learning experience.
You can watch a full video of the completed project here: https://youtu.be/l18NYKRv0g0
| Qty | Value | Footprint | References |
|---|---|---|---|
| 28 | 100 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P5.08mm_Vertical | R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25 +12 |
| 28 | 13 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P5.08mm_Vertical | R32, R33, R34, R35, R36, R37, R38, R39, R40, R41, R42, R43, R44, R45, R46, R47 +12 |
| 4 | 100u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C7, C8 |
| 4 | TPIC6595 | Package_DIP:DIP-20_W7.62mm | U3, U4, U5, U6 |
| 4 | TouchPad | TouchPads:TouchPad1 | TP2, TP3, TP5, TP6 |
| 2 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C6 |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R60 |
| 2 | 10u | Capacitor_THT:CP_Radial_D7.5mm_P2.50mm | C1, C2 |
| 2 | TC4469CPD | Package_DIP:DIP-14_W7.62mm | U1, U2 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R61 |
| 1 | 100uH | Inductor_THT:L_Radial_D7.5mm_P5.00mm_Fastron_07P | L1 |
| 1 | 1K | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 22K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 3v3 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D2 |
| 1 | 5V | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | Barrel_Jack_Switch_Pin3Ring | Connector_BarrelJack:BarrelJack_Horizontal | J1 |
| 1 | FB | TestPoint:TestPoint_Pad_4.0x4.0mm | TP4 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TP8 |
| 1 | HV | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4 |
| 1 | HV | TestPoint:TestPoint_Pad_4.0x4.0mm | TP1 |
| 1 | IRF640N | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | Large Digit 1 | LED_Filaments:Segen_Segment_69mm | U11 |
| 1 | Large Digit 2 | LED_Filaments:Segen_Segment_69mm | U12 |
| 1 | Large Digit 3 | LED_Filaments:Segen_Segment_69mm | U13 |
| 1 | Large Digit 4 | LED_Filaments:Segen_Segment_69mm | U14 |
| 1 | MBR1100RLG | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 1 | PWM | TestPoint:TestPoint_Pad_4.0x4.0mm | TP7 |
| 1 | Small Digit 1 | LED_Filaments:Segen_Segment_41mm | U7 |
| 1 | Small Digit 2 | LED_Filaments:Segen_Segment_41mm | U8 |
| 1 | Small Digit 3 | LED_Filaments:Segen_Segment_41mm | U9 |
| 1 | Small Digit 4 | LED_Filaments:Segen_Segment_41mm | U10 |
| 1 | TINYPICO | TinyPICO:TINYPICO | XA1 |

atomic14/supersise-seven-segment
The code, schematics and PCB layout are offered here without any support. It's fun project but it's also a learning experience.

atomic14/supersise-seven-segment
The code, schematics and PCB layout are offered here without any support. It's fun project but it's also a learning experience.

atomic14/supersise-seven-segment
The code, schematics and PCB layout are offered here without any support. It's fun project but it's also a learning experience.

RadioThermal/RadioThermal_Soldering_OSHW
Open Source Hardware 470KHz Induction Soldering Iron

lrvdijk/ledstrip-dmx-receiver
KiCad Project for a DMX receiver driving a LED strip with 5050 SMD RGB LEDs.



alextousss/3d_ultrasonic_scanner
An ultrasonic 3D scanner

SamWarmuth/SWSplitFlap
3D printable split flap display (software/pcb/STLs), for a more detailed split flap project see https://github.com/scottbez1/splitflap


neurorishika/MultiBiOS
High-precision, hardware-clocked olfactometer control system for behavioral neuroscience
It measures 281.9 × 90.4 mm and has 2 copper layers, 1.6 mm thick.
100 parts, built around the TC4469CPD, TPIC6595N and IRF640N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the atomic14/supersise-seven-segment repository on GitHub, at the commit this page was made from: the board is kicad/SevenSegmentClockV2/SevenSegmentClockV2.kicad_pcb and its schematic kicad/DecimalPlace/DecimalPlace.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).