

T20q100f3
Random collection of breakout boards
- Size
- 65.3 × 58.9 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 184
- Nets
- 134
- Pads
- 555
- Tracks, vias
- 934, 103
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 28 Apr 2019
- Updated
- 28 Oct 2026
Overview
T20q100f3 is an open-source printed circuit board by ataradov, from the ataradov/breakout-boards repository on GitHub. It is a 4-layer board of 65.3 × 58.9 mm with 184 parts on 134 nets, routed with 934 tracks and 103 vias.
It is built around the NTR5103N and ESDALD05UD4X. Its parts include 65 connectors, 30 capacitors, 22 resistors, 12 diodes and 8 transistors. It belongs with the interfaces and adapters and microcontroller boards boards of this library.
Main components
2NTR5103N
SOT-23-55℃~+150℃ 1 N-channel 2.6V 310mA 3Ω@4.5V 420mW 60V N-Channel SOT-23 MOSFETs ROHSonsemiMOSFETsESDALD05UD4X
SOT-23-6L0.3pF、0.6pF 100nA 16V 5.5A@8/20us 5V 6V 88W@8/20us ESD Four channels IEC 61000-4-2、IEC 61000-4-5 SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHSWeEn SemiconductorsESD And Surge Protection (TVS/ESD)
README
README.mdBreakout Boards
This is a collection of random breakout boards I developed to get started with a new device.
Firmware for the SAM D11 used as a debugger/VCP interface on some boards is available here)
Currrently available boards:
- Atmel SAME70 / SAMS70
- ST STM32G071
- GigaDevice GD32F407V (will probably work for STM32F407 as well)
- Lattice LCMXO256C
- Lattice LCMXO2-2000HC
- Nuvoton M484SIDAE
- Atmel SAMD11 USB Test Board
- Atmel SAMD11 Nano - full breakout with USB connector
- Raspberry Pi RP2040
- Gowin GW1N-UV9QN48
Errata
The boards are added here at the same time they are submitted for fabrication. There may be issues with them, but I will not know about them until the boards arrive. Those issues will not be fixed in the files, unless the boards are really broken and I need to reorder them, or I want to reorder them for some other reason.
Below is a list of known issues:
- GD32F407V - BOOT0 (pin 94) should be pulled down by a 10 kOhm resistor. This is an easy fix, there is a groud pour near the jumper.
- SAMD11 USB Test Board - Switch footprint is slightly off (mounting pads are wider than on a real switch).
Parts
184| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | 100nF | ataradov_smd:0603 | C1, C2, C10, C11, C12, C13, C14, C15, C17, C18, C19, C20, C21, C22, C23, C24 +8 |
| 8 | 470 | ataradov_smd:0603 | R8, R9, R10, R11, R12, R13, R14, R15 |
| 8 | NTR5103N | ataradov_ic:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 8 | Orange | ataradov_smd:0603_LED | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8 |
| 5 | 10K | ataradov_smd:0603x4 | RN1, RN2, RN3, RN4, RN5 |
| 5 | 1uF | ataradov_smd:0603 | C26, C27, C28, C29, C30 |
| 4 | 10K | ataradov_smd:0603 | R3, R4, R5, R22 |
| 4 | 5.1K | ataradov_smd:0603 | R17, R18, R19, R20 |
| 4 | GND | ataradov_conn:Pin-2.54mm | J72, J74, J76, J77 |
| 4 | TactSwitch | ataradov_switch:TactSwitch-6mm-Sqare-SMD | SW1, SW2, SW3, SW4 |
| 4 | ~ | ataradov_misc:MH-2.5mm-4.0mm | MH1, MH2, MH3, MH4 |
| 2 | 100K | ataradov_smd:0603 | R7, R21 |
| 2 | 100K | ataradov_smd:0603x4 | RN8, RN9 |
| 2 | 2.2K | ataradov_smd:0603 | R1, R2 |
| 2 | 2841AS | ataradov_led:2841AS | LED9, LED10 |
| 2 | 330 | ataradov_smd:0603x4 | RN6, RN7 |
| 2 | ESDALD05UD4 | ataradov_ic:SOT-23-6 | D1, D2 |
| 2 | USB-C | ataradov_conn:USB-C | J79, J80 |
| 2 | VCC | ataradov_conn:Pin-2.54mm | J67, J70 |
| 1 | 1.5K | ataradov_smd:0603 | R16 |
| 1 | 10 | ataradov_misc:TestPoint-1.27mm | J17 |
| 1 | 100 | ataradov_misc:TestPoint-1.27mm | J31 |
| 1 | 10uF | ataradov_smd:0603 | C16 |
| 1 | 12K | ataradov_smd:0603 | R6 |
| 1 | 14 | ataradov_misc:TestPoint-1.27mm | J15 |
| 1 | 18 | ataradov_misc:TestPoint-1.27mm | J11 |
| 1 | 19 | ataradov_misc:TestPoint-1.27mm | J9 |
| 1 | 2 | ataradov_misc:TestPoint-1.27mm | J29 |
| 1 | 20 | ataradov_misc:TestPoint-1.27mm | J78 |
| 1 | 22 | ataradov_misc:TestPoint-1.27mm | J7 |
| 1 | 23 | ataradov_misc:TestPoint-1.27mm | J5 |
| 1 | 24 | ataradov_misc:TestPoint-1.27mm | J1 |
| 1 | 26 | ataradov_misc:TestPoint-1.27mm | J3 |
| 1 | 29 | ataradov_misc:TestPoint-1.27mm | J30 |
| 1 | 3 | ataradov_misc:TestPoint-1.27mm | J27 |
| 1 | 30 | ataradov_misc:TestPoint-1.27mm | J22 |
| 1 | 32 | ataradov_misc:TestPoint-1.27mm | J32 |
| 1 | 33 | ataradov_misc:TestPoint-1.27mm | J24 |
| 1 | 35 | ataradov_misc:TestPoint-1.27mm | J34 |
| 1 | 36 | ataradov_misc:TestPoint-1.27mm | J26 |
| 1 | 37 | ataradov_misc:TestPoint-1.27mm | J36 |
| 1 | 38 | ataradov_misc:TestPoint-1.27mm | J28 |
| 1 | 4 | ataradov_misc:TestPoint-1.27mm | J25 |
| 1 | 40 | ataradov_misc:TestPoint-1.27mm | J14 |
| 1 | 41 | ataradov_misc:TestPoint-1.27mm | J6 |
| 1 | 43 | ataradov_misc:TestPoint-1.27mm | J8 |
| 1 | 44 | ataradov_misc:TestPoint-1.27mm | J16 |
| 1 | 46 | ataradov_misc:TestPoint-1.27mm | J18 |
| 1 | 47 | ataradov_misc:TestPoint-1.27mm | J10 |
| 1 | 48 | ataradov_misc:TestPoint-1.27mm | J12 |
| 1 | 48 MHz | ataradov_ic:CDFN-4-3.2x2.5mm | IC5 |
| 1 | 49 | ataradov_misc:TestPoint-1.27mm | J20 |
| 1 | 5 | ataradov_misc:TestPoint-1.27mm | J23 |
| 1 | 51 | ataradov_conn:Pin-2.54mm | J4 |
| 1 | 52 | ataradov_conn:Pin-2.54mm | J2 |
| 1 | 53 | ataradov_conn:Pin-2.54mm | J75 |
| 1 | 54 | ataradov_conn:Pin-2.54mm | J73 |
| 1 | 55 | ataradov_conn:Pin-2.54mm | J71 |
| 1 | 56 | ataradov_conn:Pin-2.54mm | J69 |
| 1 | 57 | ataradov_conn:Pin-2.54mm | J68 |
| 1 | 58 | ataradov_conn:Pin-2.54mm | J66 |
| 1 | 59 | ataradov_conn:Pin-2.54mm | J65 |
| 1 | 62 | ataradov_conn:Pin-2.54mm | J64 |
| 1 | 63 | ataradov_conn:Pin-2.54mm | J63 |
| 1 | 65 | ataradov_conn:Pin-2.54mm | J61 |
| 1 | 66 | ataradov_conn:Pin-2.54mm | J59 |
| 1 | 67 | ataradov_conn:Pin-2.54mm | J57 |
| 1 | 68 | ataradov_conn:Pin-2.54mm | J55 |
| 1 | 7 | ataradov_misc:TestPoint-1.27mm | J21 |
| 1 | 71 | ataradov_conn:Pin-2.54mm | J53 |
| 1 | 73 | ataradov_conn:Pin-2.54mm | J51 |
| 1 | 74 | ataradov_conn:Pin-2.54mm | J50 |
| 1 | 77 | ataradov_misc:TestPoint-1.27mm | J49 |
| 1 | 78 | ataradov_misc:TestPoint-1.27mm | J48 |
| 1 | 79 | ataradov_misc:TestPoint-1.27mm | J47 |
| 1 | 8 | ataradov_misc:TestPoint-1.27mm | J13 |
| 1 | 80 | ataradov_misc:TestPoint-1.27mm | J46 |
| 1 | 85 | ataradov_misc:TestPoint-1.27mm | J45 |
| 1 | 86 | ataradov_misc:TestPoint-1.27mm | J44 |
| 1 | 87 | ataradov_misc:TestPoint-1.27mm | J43 |
The 155 most common of 184 parts.
More from ataradov/breakout-boards
5- 4 layers66 × 56.9 mm

- 2 layers44.7 × 33.5 mm

- 2 layers45.2 × 32 mm

- 2 layers45.7 × 23.9 mm

- 2 layers26.2 × 12.7 mm

Similar boards
- 4 layers100 × 52.3 mm

- 2 layers16 × 11.3 mm

- 2 layers348.4 × 110.2 mm

- 2 layers37.8 × 50 mm

- 2 layers21.6 × 80.6 mm

- 2 layers45 × 45 mm

- 2 layers22.9 × 20.3 mm

- 4 layers91 × 53.1 mm

Nff pcb
o7-machinehum/flipper-blackhat
Linux based WiFi pentesting device for the Flipper Zero.
184 parts300
Questions
How big is the T20q100f3 PCB?
It measures 65.3 × 58.9 mm and has 4 copper layers, 1.6 mm thick.
What parts does the T20q100f3 use?
184 parts, built around the NTR5103N and ESDALD05UD4X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the T20q100f3 KiCad files?
From the ataradov/breakout-boards repository on GitHub, at the commit this page was made from: the board is t20q100f3/t20q100f3.kicad_pcb and its schematic gw1n-uv9qn48/gw1n-uv9qn48.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the T20q100f3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask ataradov before reusing the design.