Skip to the content
2 layers42 × 68.3 mmRCA to SCART, the printed circuit board in 3D

RCA to SCART Board

Size
42 × 68.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
20
Pads
57
Tracks, vias
80, 2
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
8 Jun 2018
Updated
11 Jun 2018

Overview

RCA to SCART is an open-source printed circuit board by arithmaldor, from the arithmaldor/RCA-to-SCART repository on GitHub. It is a 2-layer board of 42 × 68.3 mm with 10 parts on 20 nets, routed with 80 tracks and 2 vias.

README

README.md

Copyright and Disclaimer

Copyright: Jacob Proctor 2018

This documentation describes Open Hardware and is licensed under the CERN OHL v. 1.2.

You may redistribute and modify this documentation under the terms of the CERN OHL v.1.2. (http://ohwr.org/cernohl). This documentation is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. Please see the CERN OHL v.1.2 for applicable conditions

RCA to SCART Board

Output version of the SCART to RCA board. This one has optional sync attentuation via a jumper (closed to bypass resistor footprint) and optional power input via microusb for TVs that automatically switch to SCART (just leave the usb and 100 ohm resistor footprints blank if you don't need this).

Parts

SCART Connector: K-SCARTX-024, available on Mouser

RCA Connector: PJRAS3X2S01 is available on Mouser and Digikey, but the colors are wrong. Here are the ones I used, a bit cheaper per part:

https://www.ebay.com/itm/QTY-10-6-WAY-PCB-FEMALE-RCA-JACKS-GREEN-YELLOW-BLUE-WHITE-RED-RED-RCA-268N1-14/112220720415?var=null

microusb port: Molex 105017-0001

Resistors: 0805 size, 470 ohm for sync attenuation, 100 ohm for dividing the voltage for RGB and TV detect on pins 8 and 16. Just about any decent quality ones will do.

Mounting hole size is M3, can be used with motherboard standoffs for mounting on MDF or acrylic or something else.

Changelog

0.1 - This board is untested, I may be a few soon after which I will update the version number to 1.0 if everything works out.

0.2 - The shield througholes of the microusb port were not connected to ground, this has been fixed. I also moved a few traces around to make it easier to disconnect pin 8 if it is causing your TV to force to 16:9.

OSHPark

https://oshpark.com/shared_projects/9mo0B0iU

Parts

10
QtyValueFootprintReferences
4Conn_01x01Mounting_Holes:MountingHole_3.2mm_M3J1, J2, J3, J4
1100Resistors_SMD:R_0805_HandSoldering100Ω
13x2_RCANew Footprints:3x2_RCARCA1
1Conn_Coaxial_PowerConnectors_USB:USB_Micro-B_Molex-105017-00015V USB
1Jumper_NO_SmallJumper:JumperJP1
1RResistors_SMD:R_0805_HandSoldering470Ω
1SCART-FNew Footprints:SCART_FSCART1

Similar boards

  • 2 layers57 × 55.2 mmLogicAnalyzer, the printed circuit board in 3D

    LogicAnalyzer

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    10 parts5.1kGPL-3.0
  • 2 layers32.2 × 15.4 mmProtector, the printed circuit board in 3D

    Protector

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    10 parts4.3kMIT
  • 2 layers26 × 18 mmConn, the printed circuit board in 3D

    Conn

    yaqwsx/KiKit

    Automation tools for KiCAD

    10 parts2.1kMIT
  • 2 layers44.3 × 30.5 mmLime2-SATA RevA, the printed circuit board in 3D

    Lime2-SATA RevA

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    10 parts1.5k
  • 2 layers17.8 × 43.2 mmNano Adapter, the printed circuit board in 3D

    Nano Adapter

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    10 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    10 parts1kGPL-3.0

Questions

How big is the RCA to SCART PCB?

It measures 42 × 68.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the RCA to SCART use?

10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the RCA to SCART KiCad files?

From the arithmaldor/RCA-to-SCART repository on GitHub, at the commit this page was made from: the board is RCA to SCART.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the RCA to SCART design in my own project?

Its repository states no licence, so its author keeps all rights: ask arithmaldor before reusing the design.