Skip to the content
2 layers40.9 × 20.4 mmHD15-to SCART, the printed circuit board in 3D

Simple HD15 to SCART connector adapter

Size
40.9 × 20.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
3
Nets
21
Pads
43
Tracks, vias
55, 8
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
12 Jun 2019
Updated
2 Aug 2019

Overview

HD15-to SCART is an open-source printed circuit board by arithmaldor, from the arithmaldor/HD15-to-SCART repository on GitHub. It is a 2-layer board of 40.9 × 20.4 mm with 3 parts on 21 nets, routed with 55 tracks and 8 vias.

README

README.md

Copyright and Disclaimer

Copyright: Jacob Proctor

This documentation describes Open Hardware and is licensed under the CERN OHL v. 1.2.

You may redistribute and modify this documentation under the terms of the CERN OHL v.1.2. (http://ohwr.org/cernohl). This documentation is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. Please see the CERN OHL v.1.2 for applicable conditions

VGA to SCART

This is a passive adapter that simply connects the RGB and sync pins from a VGA connector and the right and left audio pins from a 3.5mm jack to the corresponding pins on a male SCART connector. It is unidirectional and cannot be used for VGA output from a SCART device. It does not convert RGBHV to RGBS or 31khz to 15khz or anything fancy like that.

Uses

The main purpose of this board for me is to replace SCART cables with VGA cables. Using this adapter you can run a VGA cable from a breakout adapter to a gscartsw for example without having to worry about making your own cables or having custom ones made. I'm sure that other uses can be found.

BOM

There are only 3 parts so I thought I would just list them here instead of making a full BOM. Listed are digikey links but the parts are pretty common and it should be possible to substitute others, just compare datasheets for the footprints. VGA Connector: https://www.digikey.com/product-detail/en/amphenol-icc-fci/ICD15S13E6GV00LF/609-2802-ND/1090326 Headphone Jack: https://www.digikey.com/product-detail/en/cui-inc/SJ1-3533NG/CP1-3533NG-ND/738701 SCART Connector: Any will do, console5.com has new ones and reclaimed ones. New: https://console5.com/store/scart-plug-21-pin-male-cable-connector.html Reclaimed: https://console5.com/store/reclaimed-scart-jp21-plug-21-pin-male-cable-connector.html

Assembly

Use the photos for reference. Pin 20 of the SCART connector (the point) goes towards the left when looking at the top of the board. You can also solder a wire or component leg between the shield and the spare ground pin on the board.

Parts

3
QtyValueFootprintReferences
1AudioJack3Tinkerplunk:Tall_Skinny_Headphone_Universal_CUI_SJ1-353XNXJ2
1DB15_Female_HighDensityTinkerplunk:VGAJ1
1SCART-FTinkerplunk:MALE_SCARTJ3

Similar boards

  • 2 layers40 × 30 mmBlinky, the printed circuit board in 3D

    Blinky

    earthtojake/text-to-cad

    Design physical products with AI

    3 parts26kMIT
  • 2 layers51.9 × 16 mmPassive2-rpi non standard adapter, the printed circuit board in 3D

    Passive2-rpi non standard adapter

    hzeller/rpi-rgb-led-matrix

    Controlling up to three chains of 64x64, 32x32, 16x32 or similar RGB LED displays using Raspberry Pi GPIO

    3 parts4.4kGPL-2.0
  • 2 layers16.3 × 16.3 mmSensor, the printed circuit board in 3D

    Sensor

    scottbez1/splitflap

    DIY split-flap display

    3 parts4.2k
  • 2 layersSub, the printed circuit board in 3D

    Sub

    atopile/atopile

    Design circuit boards with code! ✨ Get software-like design reuse 🚀, validation, version control and collaboration in hardware; starting with electronics ⚡️

    3 parts4kMIT
  • 2 layers85 × 30 mmDual stomp, the printed circuit board in 3D

    Dual stomp

    torvalds/GuitarPedal

    Linus learns analog circuits

    3 parts2.5kGPL-2.0
  • 2 layers124.5 × 33.7 mm172319-1 connector, the printed circuit board in 3D

    172319-1 connector

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    3 parts1.2k
  • 2 layers10.5 × 83 mmProgrammingAdapter, the printed circuit board in 3D

    ProgrammingAdapter

    stuartpittaway/diyBMSv4

    Version 4 of the diyBMS

    3 parts1.1k
  • 2 layers21.2 × 51.3 mmPico reset, the printed circuit board in 3D

    Pico reset

    hackclub/sprig

    🍃 Learn to code by making games in a JavaScript web-based game editor.

    3 parts1.1kMIT

Questions

How big is the HD15-to SCART PCB?

It measures 40.9 × 20.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the HD15-to SCART use?

3 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the HD15-to SCART KiCad files?

From the arithmaldor/HD15-to-SCART repository on GitHub, at the commit this page was made from: the board is HD15-to-SCART.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the HD15-to SCART design in my own project?

Its repository states no licence, so its author keeps all rights: ask arithmaldor before reusing the design.