
Rs probe
probe-rs/rusty-probe
This is an open hardware probe for the Serial Wire Debug (SWD) and JTAG protocol. Based on the RP2040 MCU.

This repository contains open hardware design files of the LED flexible PCB designed for Raspberry Pi. It includes a PCA9685BS GPIO expander which drives five RGB LEDs.
Rpi led flex board is an open-source printed circuit board by antmicro, from the antmicro/rpi-led-flex-board repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 70.3 × 35.6 mm with 29 parts on 42 nets, routed with 252 tracks and 43 vias.
It is built around the PCA9685BS,118 and LTST-C19HE1WT. Its parts include 19 resistors, 5 diodes, 1 capacitor, 1 IC and 1 connector.
Copyright (c) 2022 Antmicro <https://www.antmicro.com>_
.. figure:: img/rpi-led-flex-board.jpg
This repository contains open hardware design files of the LED flexible PCB designed for Raspberry Pi.
It includes a PCA9685BS <https://www.nxp.com/products/power-management/lighting-driver-and-controller-ics/ic-led-controllers/16-channel-12-bit-pwm-fm-plus-ic-bus-led-controller:PCA9685>_ GPIO expander which drives five RGB LEDs.
The GPIO expander is connected to the Raspberry PI over an I2C interface exposed on the camera connector.
This board has been developed and tested with Raspberry Pi 4B.
It has been developed as a part of a compute cluster and fits mechanically in the Open Hardware Raspberry Pi enclosure <https://github.com/antmicro/rpi-compute-cluster-enclosure>_.
The design files were prepared in KiCad. The PCB stackup definition assumes a polyimide, flexible PCB with FR4 stiffeners below the LEDs and the FFC end.
The main repository directory contains KiCad PCB project files, a LICENSE and README. The remaining files are stored in the following directories:
lib - contains the component librariesimg - contains graphics for this READMEApache-2.0 <LICENSE>_
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | R_49R9_0402 | rpi-led-flex-board-footprints:0402-res | R3, R4, R6, R9, R11, R12, R14, R15, R17, R18 |
| 5 | LTST-C19HE1WT | rpi-led-flex-board-footprints:LED_Dual0603 | D1, D2, D3, D4, D5 |
| 5 | R_100R_0402 | rpi-led-flex-board-footprints:0402-res | R2, R5, R10, R13, R16 |
| 2 | R_4k7_0402 | rpi-led-flex-board-footprints:0402-res | R7, R8 |
| 1 | C_100n_0402 | rpi-led-flex-board-footprints:0402-cap | C1 |
| 1 | PCA9685BS,118 | rpi-led-flex-board-footprints:QFN-28_6x6mm_P0.65mm | U1 |
| 1 | R_0R_0402 | rpi-led-flex-board-footprints:0402-res | R19 |
| 1 | R_10k_0402 | rpi-led-flex-board-footprints:0402-res | R1 |
| 1 | TE_1-1734248-5_FLEX | rpi-led-flex-board-footprints:TE_1-1734248-5_FLEX | J1 |
| 1 | antmicro_logo | rpi-led-flex-board-footprints:antmicro-logo_scaled_15mm_silk | N1 |
| 1 | oshw_logo | rpi-led-flex-board-footprints:OSHW-Logo_5.7x6mm_SilkScreen | N2 |

probe-rs/rusty-probe
This is an open hardware probe for the Serial Wire Debug (SWD) and JTAG protocol. Based on the RP2040 MCU.

probe-rs/hs-probe
This is an open hardware probe for the Serial Wire Debug (SWD) and JTAG protocol. It utilizes an STM32F723 MCU which has an USB 2.0 High-speed Phy.

NabuCasa/yellow
Home Assistant Yellow - hardware for Home Assistant which grows with your needs.




It measures 70.3 × 35.6 mm and has 2 copper layers, 0.1 mm thick.
29 parts, built around the PCA9685BS,118 and LTST-C19HE1WT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the antmicro/rpi-led-flex-board repository on GitHub, at the commit this page was made from: the board is rpi-led-flex-board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).