4 layers102 × 102 mm
Controller
Angelo13C/3d-printer
Firmware, electronics, mechanics and control interface of a 3D printer
97 parts2
4 layers52 × 52 mm
Hot plate controller
Angelo13C/hot-plateIt's based on an STM32F730R8T6. The board receives stable 24V from an external power supply unit and requires around 10A of current.
- Size
- 52 × 52 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 84
- Nets
- 77
- Pads
- 289
- Tracks, vias
- 577, 93
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 29 Dec 2023
- Updated
- 29 May 2024
Overview
Hot plate controller is an open-source printed circuit board by Angelo13C, from the Angelo13C/hot-plate repository on GitHub. It is a 4-layer board of 52 × 52 mm with 84 parts on 77 nets, routed with 577 tracks and 93 vias.
It is built around the STM32F730R8T6, USBLC6-2SC6 and AON7524, with the MCU45P04-TP and SK510A-LTP among its other parts. Its parts include 21 capacitors, 21 connectors, 19 resistors, 6 diodes and 3 ICs. It belongs with the STM32 boards of this library.
Main components
5
STM32F730R8T6
LQFP-64(10x10)-40℃~+85℃ 1.7V~3.6V 12bit 12bit 216MHz 256KB 32 Bit 50 64KB ARM Cortex-M7 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
USBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)AON7524
DFN-8(3x3)-55℃~+150℃ 1 N-channel 1.2V 2.25nF 25A、28A 3.3mΩ@10V 30V 50nC@10V DFN-8(3x3) MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
MCU45P04-TP
DPAKMOSFETsMicro Commercial Components
SK510A-LTP
DO-214AC(SMA)-55℃~+150℃ 1 Independent 100A 100V 10uA 5A 850mV@5A DO-214AC(SMA) Schottky Diodes ROHSMicro Commercial ComponentsSchottky Diodes
README
electronics/controller/README.mdElectronics
This is the electrical control board on which the firmware runs.
It's based on an STM32F730R8T6. The board receives stable 24V from an external power supply unit and requires around 10A of current.
On the board there's a switching regulator that converts the 24V to 3.3V, which is used by: thermistors, display, MLX90614 and microcontroller.
Schematic
This is the electrical schematic of the board:
PCB
The PCB (dimensions: 52mm x 52mm) has 4 layers (PWR/SIGNAL, GND, GND, PWR/SIGNAL). This is an image of the top layer:
Parts
84| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Project:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C5, C6, C12, C18 |
| 6 | 4.7KΩ | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R13, R14, R15, R17, R18 |
| 4 | 3.3μF | Project:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C17, C19, C20, C21 |
| 3 | 10KΩ | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9, R11, R16 |
| 3 | 10μF | Project:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14, C15, C16 |
| 3 | 2.2KΩ | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R12 |
| 3 | GREEN | Project:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2, D3, D4 |
| 2 | 300Ω | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R10 |
| 2 | 30pF | Project:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9, C10 |
| 2 | 4.7μF | Project:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8 |
| 2 | 5.1KΩ | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | AON7524 | Project:DFN-8-1EP_3x3mm_P0.65mm_EP1.55x2.4mm | Q1, Q2 |
| 2 | SW_Push | Project:SW_LS38J2F-T | SW1, SW2 |
| 1 | 0.1μF | Project:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11 |
| 1 | 100KΩ | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19 |
| 1 | 10μH | Project:HPC 5040NF-100M | L1 |
| 1 | 12A | Project:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | 2.7KΩ | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 47Ω | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 47μF | Project:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13 |
| 1 | 500mA | Project:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F2 |
| 1 | 8MHz | Project:Crystal_HC49-4H_Vertical | Y1 |
| 1 | AP63203WU-7 | Project:AP63203WU-7_DIO | U3 |
| 1 | Board_Thermistor | Project:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | TH1 |
| 1 | D_Zener | Project:D_SOD-123 | D5 |
| 1 | Display_Connector | Project:PinHeader_1x14_P2.54mm_Vertical | J2 |
| 1 | Extra_PA10 | Project:PinHeader_1x01_P2.54mm_Vertical | J14 |
| 1 | Extra_PA8 | Project:PinHeader_1x01_P2.54mm_Vertical | J12 |
| 1 | Extra_PA9 | Project:PinHeader_1x01_P2.54mm_Vertical | J13 |
| 1 | Extra_PB8 | Project:PinHeader_1x01_P2.54mm_Vertical | J18 |
| 1 | Extra_PB9 | Project:PinHeader_1x01_P2.54mm_Vertical | J19 |
| 1 | Extra_PC10 | Project:PinHeader_1x01_P2.54mm_Vertical | J15 |
| 1 | Extra_PC11 | Project:PinHeader_1x01_P2.54mm_Vertical | J16 |
| 1 | Extra_PC12 | Project:PinHeader_1x01_P2.54mm_Vertical | J17 |
| 1 | Extra_PC14 | Project:PinHeader_1x01_P2.54mm_Vertical | J20 |
| 1 | Extra_PC15 | Project:PinHeader_1x01_P2.54mm_Vertical | J21 |
| 1 | Extra_PC8 | Project:PinHeader_1x01_P2.54mm_Vertical | J10 |
| 1 | Extra_PC9 | Project:PinHeader_1x01_P2.54mm_Vertical | J11 |
| 1 | Fan_Connector | Project:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | Hot_Plate_Connector | Project:TERM_BLK_2POS_SIDE_ENTRY_5MM_691137710002 | J3 |
| 1 | MCU45P04-TP | Project:TO-252-2 | Q3 |
| 1 | MLX90614_Connector | Project:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | Power_Supply_Connector | Project:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | RED | Project:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | SK510A-LTP | Project:SMADO-214AC_LEAD-FRAME_MCC-L | D6 |
| 1 | STM32F730R8T6 | Project:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | SWD_Connector | Project:PinHeader_1x06_P2.54mm_Vertical | J9 |
| 1 | Thermistor_1_Connector | Project:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Thermistor_2_Connector | Project:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | USBLC6-2SC6 | Project:SOT-23-6_Handsoldering | U2 |
| 1 | USB_C_Receptacle_USB2.0 | Project:USB_C_Receptacle_GCT_USB4085 | J1 |
The 80 most common of 84 parts.
Questions
How big is the Hot plate controller PCB?
It measures 52 × 52 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Hot plate controller use?
84 parts, built around the STM32F730R8T6, USBLC6-2SC6, AON7524 and MCU45P04-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hot plate controller KiCad files?
From the Angelo13C/hot-plate repository on GitHub, at the commit this page was made from: the board is electronics/controller/hot-plate-controller.kicad_pcb and its schematic electronics/controller/hot-plate-controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hot plate controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask Angelo13C before reusing the design.
Similar boards
- 2 layers80 × 50 mm
Greaseweazle F7 Plus V2
aerobaticant/Greaseweazle-F7-Plus
My board design for Keir Fraser's Greaseweazle
66 parts30 - 4 layers42 × 42 mm
- 2 layers60 × 55 mm
- 4 layers46 × 238 mm
Assembly review
OAK-WJR/rocket-flight-computer
Amateur rocket flight computer: single-board KiCad PCB (STM32H743), firmware and diagnostics
208 parts - 4 layers150 × 155 mm
Usb console server
TheKingOfChaos/Console-Server
48 RS-232 console ports on one Raspberry Pi: three identical boards, 16 ports each. Built from the design record of 2026-10-10. KiCad 10.0.7. This is Rev B (git tag rev-A is the first board).
361 parts - 4 layers52.5 × 46.5 mm
- 2 layers122.5 × 70.5 mm
Main pcb
Potato-eater/Legacy2026
github repo for Robocup Junior Australia lightweight soccer team
74 parts2