Skip to the content
2 layers120.4 × 121 mmTouchDeck, the printed circuit board in 3D

Touchdeck is a macropad with touch sensitive display, it has no keys.

Size
120.4 × 121 mm
Copper layers
2
Thickness
1.6 mm
Parts
21
Nets
50
Pads
148
Tracks, vias
402, 83
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
8 May 2026
Updated
25 May 2026

Overview

TouchDeck is an open-source printed circuit board by andaniayan-jpg, from the andaniayan-jpg/TouchDeck repository on GitHub. It is a 2-layer board of 120.4 × 121 mm with 21 parts on 50 nets, routed with 402 tracks and 83 vias.

It is built around the ESP32-S3-WROOM-1-N8, AP2112K-3.3 and USBLC6-2SC6, with the SFH 4546 and WS2812B among its other parts. Its parts include 7 resistors, 3 capacitors, 3 ICs, 2 diodes and 2 connectors. It belongs with the ESP32 boards of this library.

Main components

5

README

README.md

TouchDeck

A macropad with touch sensor TouchDeck product

Touchdeck is a macropad with touch sensitive display, it has no keys.

Table of Contents

WHAT IS TOUCHDECK WHAT MAKES IT UNIQUE FEATURES HOW TO USE IT BILL OF MATERIALS SCHEMATIC OVERVIEW PCB details 3D design Assembly Guide Firmware


What is TouchDeck?

TouchDeck is a device made with ESP32 as the MCU, it acts a touch pad making it both a macropad and a scribble pad. It has 2 modes.

1. Macropad Mode The screen acts like a touchpad, which digital keys visible on the screen, it enables the device to act as a Touch Screen MacroPad.

2. Scribble Pad Mode When switched to Scribble pad mode, it shows a plain white canvas that can be used to take notes, doodle and etc. NOTHING IS SAVED PERMANENTLY, ONCE EXITING THIS MODE, REMOVES ALL THE WORK.

What Makes It Unique

It is unique because it doesnt use any buttons or keys like ordinary macropad, it has touch screen. It is unique because it acts as both macropad and scribble pad. It has a customised PCB, LED, buzzer and etc.

Main Features

  • ESP32-S3 based custom PCB
  • 3.5 inch SPI TFT touchscreen display
  • XPT2046 touch controller
  • USB-C power and data
  • On-screen macro buttons
  • Temporary scribble/doodle mode
  • Back and clear controls
  • USB HID keyboard shortcut output
  • WS2812B RGB status LED
  • Buzzer feedback
PCB top view PCB bottom view

How to Use It

1. Power the Device

Connect the device with the laptop or PC. Turn on with power switch, RGB LED turns on and shows the status.

2. Select the mode, Macropad or scribble.

When powered on, the screen shows two main options:

  • MacroPad Mode
  • ScribblePad Mode

Tap the mode you want to use.

3. MacroPad Mode

The touchscreen shows several shortcut buttons. When a button is touched, the ESP32-S3 sends a keyboard shortcut to the connected laptop via USB HID.

You can add, remove, increase and reduce the sizes of buttons according to your choice by changing the firmware, as it is a custom PCB!!!

4. ScribblePad Mode

The screen becomes a temporary drawing area. You can write with your finger or a capacitive stylus, doodle quick ideas, sketch small layouts, or scribble notes while thinking.

The drawing is not saved — it is purely temporary.

  • Clear — removes the drawing from the screen
  • Back — returns to the home screen and clears the canvas
UI overview

Bill of Materials (BOM)

visit "" for BOM.

Component connections

for component connections, refer to the schematic image or go through the schematic source file to view exact connections.

Assembly Guide

All the components used are present in the folder cad_assembly in STEP/STP format, for 3D model, Enclousre, and 3D parts overview, go through that folder.

Tools needed

-Soldering iron and flux -Tweezers -USB-C data cable


Step 1 — Solder the Small Components

Let's start by soldering the tiny parts. First, apply some flux to the pads where the resistors and capacitors will go. Carefully position each component in place and solder them down. Since resistors and capacitors are the smallest parts, it's easier to tackle these first.

Step 2 — Solder the USB-C Connector

Next up is the USB-C connector. Begin by putting a little solder on the ground pads in the center of the PCB. Align the USB-C connector so all the pins match up with the pads. Tack down one corner to hold it in place, then double-check everything’s aligned before soldering the rest. Finally, solder the 5V and ground shield tabs — these will need a bit more heat to get a good connection.

Step 3 — Solder the Voltage Regulator and ESD IC

Time to solder the voltage regulator and ESD IC. Start with the AP2112K (U2) in its SOT-23-5 package. Just make sure to pay attention to the orientation according to the silkscreen. After that, move on to the USBLC6-2SC6 (U3) in its SOT-23-6 package, keeping an eye on the pin 1 indicator.

Step 4 — Solder the Transistor and Buzzer

For the next step, solder the transistor (Q1), which is the 2N3904 in the SOT-23 footprint. Then, insert the passive buzzer (LS1) into the through-hole, making sure the positive marking aligns with the pad label. Solder it from the bottom.

Step 5 — Solder the WS2812B LED (U4)

Next, let’s work on the WS2812B LED, which has an integrated controller. First, apply a bit of flux to all four pads. Solder one of the corner pads first, then work on the others. Just a tip: try not to apply heat for too long on each pad.

Step 6 — Solder the Push Buttons

Moving on, place the push buttons (SW1 for Boot and SW2 for Reset) into their through-holes. Insert them from the top and then solder their four legs from the bottom.

Step 7 — Solder the ESP32-S3-WROOM-1 Module

This is one of the most important parts of the project. Start by applying flux on all the pads on three sides of the module footprint. Carefully position the module, ensuring the edges align with the PCB pads. Tack down two corner pads to secure it, then solder each pad using a drag-soldering method or solder wick. Make sure to check under a magnifying glass to spot any solder bridges.

Remember: Do not solder the antenna area. The module has a PCB antenna, so keep that section clear.

Step 8 — Solder the Display Connector (J2)

Now, insert the 1×14 female header into J2. If you’re not using a header, you can solder wires directly instead. Solder all 14 pins from the bottom.

Step 9 — Power-On Test (Before Display)

Before connecting the display, let's check if the power is working. Connect a USB-C cable from the board to your computer. Use a multimeter to measure the voltage between the 3.3V test point and ground. You should see a reading between 3.28–3.35V. If it’s 0V or over 3.4V, disconnect immediately and check the solder joints on U2 and C1/C2.

Step 10 — Attach the Display Module

Now it’s time to add the 3.5" ILI9488 display module into J2. Be careful to check the pin 1 orientation — there’s a marking on the silkscreen to help you out. If you’re doing a permanent build, you might want to use a little hot glue or double-sided foam tape to hold the display flat against the PCB.

Step 11 — Mount Everything in the Enclosure

Finally, position the PCB in the bottom of the enclosure, making sure the mounting holes line up with the standoff posts. Insert the M2.5 × 6mm standoffs from below through the PCB holes. Then, place the enclosure top frame over the display and secure it with M2.5 × 4mm screws on both the top and bottom.

And that’s it! At this point, you should have everything nicely assembled and ready to go.



Hardware design files are released under CERN Open Hardware Licence v2 (CERN-OHL-S). Firmware source code is released under MIT License. See LICENSE for full terms.

Parts

21
QtyValueFootprintReferences
210kΩResistor_SMD:R_0603_1608MetricR5, R6
210μFCapacitor_SMD:C_0805_2012MetricC1, C2
21kΩResistor_SMD:R_0603_1608MetricR7, R8
25.1kΩResistor_SMD:R_0603_1608MetricR1, R2
2SW_PushButton_Switch_THT:SW_PUSH_6mmSW1, SW2
11μFCapacitor_SMD:C_0805_2012MetricC7
12N3904Package_TO_SOT_THT:TO-92_InlineQ1
1330ΩResistor_SMD:R_0603_1608MetricR9
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U3
1BuzzerBuzzer_Beeper:Buzzer_12x9.5RM7.6BZ1
1Conn_01x14Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_VerticalJ2
1ESP32-S3-WROOM-1RF_Module:ESP32-S3-WROOM-1U1
1SFH4546LED_THT:LED_D5.0mmD1
1USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U4
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01AJ1
1WS2812BLED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mmD2

Similar boards

  • 4 layers100 × 100 mmNotSmart Speaker, the printed circuit board in 3D

    NotSmart Speaker

    BBroadbent/NotSmart-Speaker

    A open-hardware, local-first "dumb" smart speaker powered by an ESP32, PCM5100A DAC, TPA3118 Class-D amp, and 20V USB-PD.

    102 parts
  • 4 layers100 × 100 mmBedberry, the printed circuit board in 3D

    Bedberry

    DarwinInnovation/bedberry

    Open source PCB for bed/chair control

    88 parts1MIT
  • 2 layers80 × 117.3 mmMicromouse pcb, the printed circuit board in 3D

    Micromouse pcb

    jtorbett/micromouse-pcb

    An electronic design for a micromouse

    98 parts1
  • 2 layers55 × 58 mmRemodian pcb, the printed circuit board in 3D

    Remodian pcb

    mincomk/remodian

    Meridian Remote Control 📢🔺

    35 parts
  • 2 layers20.3 × 40.5 mmLightbarriersync, the printed circuit board in 3D

    Lightbarriersync

    TheTesla/lightbarriersync

    Robust light barrier with snychronized carrierer wave receiver

    53 parts
  • 2 layers40 × 80 mmSenseBeTx rev1, the printed circuit board in 3D

    SenseBeTx rev1

    Appiko/sense_snap_hw

    This repository contains all the KiCad based PCB design and related documentation for all the PCBs developed at Appiko.

    38 parts2
  • 2 layers29.5 × 57 mmSecond, the printed circuit board in 3D

    Second

    BillBanakos/Projects

    This is a repository of the projects i have done in my unveristy years

    17 parts
  • 4 layers108.6 × 87.7 mmBlinky badge light, the printed circuit board in 3D

    Blinky badge light

    rowr111/blinky-badge-light

    lighting badge with unique patterns and sound reactivity

    123 parts9MIT

Questions

How big is the TouchDeck PCB?

It measures 120.4 × 121 mm and has 2 copper layers, 1.6 mm thick.

What parts does the TouchDeck use?

21 parts, built around the ESP32-S3-WROOM-1-N8, AP2112K-3.3, USBLC6-2SC6 and SFH 4546. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the TouchDeck KiCad files?

From the andaniayan-jpg/TouchDeck repository on GitHub, at the commit this page was made from: the board is pcb_source_files/TOUCHdeck.kicad_pcb and its schematic pcb_source_files/TOUCHdeck.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the TouchDeck design in my own project?

Its repository states no licence, so its author keeps all rights: ask andaniayan-jpg before reusing the design.