2 layers100 × 21 mm
2 layers47 × 48.8 mm
Lifesense pcb
amozoss/lifesense-pcb1Senior project hardware made in kicad
- Size
- 47 × 48.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 54
- Nets
- 78
- Pads
- 270
- Tracks, vias
- 1,670, 140
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 31 May 2014
- Updated
- 29 Dec 2014
Overview
Lifesense pcb is an open-source printed circuit board by amozoss, from the amozoss/lifesense-pcb repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board of 47 × 48.8 mm with 54 parts on 78 nets, routed with 1,670 tracks and 140 vias.
It is built around the TM4C123GH6PMI, CC3000 and TPS73633DBV, with the DTC114E among its other parts. Its parts include 19 capacitors, 15 resistors, 6 connectors, 4 diodes and 3 ICs.
Main components
4
TM4C123GH6PMI
LQFP-64(10x10)-40℃~+85℃ 1.08V~3.63V 12bit 256KB 2KB 32 Bit 32KB 43 80MHz ARM Cortex-M4F Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSTexas InstrumentsMicrocontrollers (MCU/MPU/SOC)
CC3000
UncategorisedTexas Instruments
TPS73633DBV
SOT-23-5-40℃~+125℃@(Tj) 1 3.3V 30uVrms 400mA 5.5V 550uA 58dB@(10kHz) 75mV@(400mA) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Reverse-polarity current protection、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
DTC114E
--55℃~+150℃ 100mA 100nA 350mW 50V NPN - Bipolar (BJT)onsemiBipolar (BJT)
README
README.mdlifesense-pcb
Senior project hardware
CC3000 lib/footprint obtained here: https://github.com/mcous/kicad-lib/
Software
The pcb software can be found at lifesense-pcb-software
Images
Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | R | lifesense:SMD-0603_r | R2, R9, R10, R11, R12, R14, R25, R26, R29 |
| 6 | 0.01uF | lifesense:SMD-0603_c | C3, C5, C8, C10, C11, C18 |
| 4 | 330 | lifesense:SMD-0603_r | R3, R4, R5, R27 |
| 3 | 1.0uF | lifesense:SMD-0603_c | C7, C12, C14 |
| 3 | DTC114E | lifesense:DTC114EET1G | Q1, Q2, Q3 |
| 3 | LED | LEDs:LED-0805 | D1, D2, D3 |
| 2 | 0.1uF | lifesense:SMD-0603_c | C4, C6 |
| 2 | 10pF | lifesense:SMD-0603_c | C31, C32 |
| 2 | 24pF | lifesense:SMD-0603_c | C28, C29 |
| 2 | CONN_01X01 | lifesense:Pin_Header_Straight_1x01 | P2, P21 |
| 2 | CONN_10X2 | Pin_Headers:Pin_Header_Straight_2x10 | J1, J4 |
| 1 | 100nF | lifesense:SMD-0603_c | C102 |
| 1 | 10K | lifesense:SMD-0603_r | R28 |
| 1 | 1M | lifesense:SMD-0603_r | R31 |
| 1 | 1pF | lifesense:SMD-0603_c | C101 |
| 1 | 2.2uF | lifesense:SMD-0603_c | C22 |
| 1 | 4.7uF | lifesense:SMD-0603_c | C100 |
| 1 | ANT | lifesense:ant_Wigle_A2_4G | A1 |
| 1 | CC3000 | texas-addition:CC3000 | IC1 |
| 1 | CONN_6 | Pin_Headers:Pin_Header_Straight_1x06 | P1 |
| 1 | CRYSTAL | lifesense:AB26TRB | Y1 |
| 1 | CRYSTAL | lifesense:ABM3 | Y2 |
| 1 | Green | LEDs:LED-0805 | D4 |
| 1 | SW_PUSH | lifesense:B3S-1000 | SW3 |
| 1 | TM4C123GH6PM | lifesense:lqfp64 | U1 |
| 1 | TPS73633DBV | lifesense:TPS73633DBV | U2 |
| 1 | USB-MINI-B | lifesense:ZX62-AB-5PA(11) | CON1 |
Similar boards
- 4 layers30 × 55 mm
- 4 layers68.6 × 52.1 mm
Roadrunner
jakeson21/Roadrunner-TM4C123G
Arduino clone based on TI's TM4C123G, an ARM M4F running at 80 MHz.
104 parts3GPL-3.0 - 2 layers161.5 × 90.2 mm
Master
cactorium/UCFBrainStuff
EEG software, alpha stages. Will be opensourced when it's working!
117 partsMIT - 2 layers67 × 55 mm
- 2 layers100 × 100 mm
Synchro2
waynegramlich/synchro_drive_motor_driver_pcb
Dual motor drive for dual motor synchro drive PCB
98 parts - 2 layers50.8 × 60 mm
Eos tm4c123-board
embeddedos-org/eCAD-Hardware-Products
Hardware designs + EE docs + Board datasheets of Multiple products
87 parts8MIT - 4 layers54.3 × 24 mm
Questions
How big is the Lifesense pcb PCB?
It measures 47 × 48.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Lifesense pcb use?
54 parts, built around the TM4C123GH6PMI, CC3000, TPS73633DBV and DTC114E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Lifesense pcb KiCad files?
From the amozoss/lifesense-pcb repository on GitHub, at the commit this page was made from: the board is lifesense-pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Lifesense pcb design in my own project?
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).