

4gates
read-only mirror
- Size
- 84 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 80
- Nets
- 75
- Pads
- 247
- Tracks, vias
- 566, 91
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 Jun 2024
- Updated
- 7 Sep 2026
Overview
4gates is an open-source printed circuit board by Alloyed, from the Alloyed/KitsBlips repository on GitHub, published under the MIT licence. It is a 2-layer board of 84 × 100 mm with 80 parts on 75 nets, routed with 566 tracks and 91 vias.
It is built around the J113. Its parts include 32 resistors, 17 connectors, 13 capacitors, 6 diodes and 4 ICs.
Main components
1README
README.mdKitsBlips
Monorepo for my Eurorack/synthesizer hobby projects! (that's me, I'm kit)
Everything is always in a state of "not-quite-finished". if something is unclear or unusable in its current state, and you want to use it, feel free to open an issue or contact me.
For technical reasons, this project is ordered by toolset and not by module. this means the full source for a single module may be across multiple folders! Sorry.
unless otherwise listed, all code is MIT licensed. All hardware designs and graphics (kicad, svg etc) are CC-BY-SA 4.0.
Building/Installing
Each project/folder has a specific readme that includes extra steps if necessary, but in general, builds are managed using cmake.
$ mkdir -p <folder>/build && cd <folder>/build
$ cmake .. -DCMAKE_BUILD_TYPE=<build type: Debug, MinSizeRel, RelWithDebInfo>
$ cmake --build . --config=<the build type>
$ cmake --install . --prefix <location> # if the target supports installation
$ ctest # if the target has unit testsonce you have all your configurations set up, you can quickly rebuild all/run tests using rebuild-all.sh.
Projects
For Hardware:
For VCV Rack:
- /vcvrack
- Modules for VCV Rack
For DAWS:
- /daw
- Modules for DAWS (VST3/CLAP plugins)
- /clapeze
- Microframework for writing clap plugins
- /kitgui
- UI library for clap plugins
Shared:
- /panels
- Art/Panel designs.
- /kitdsp
- Shared DSP code, runs on all platforms
- /kitdsp-gpl
- DSP code with GPL algorithms. This is the only folder that comes with extra license restrictions!
AI statement
KitsBlips will not accept PRs that are generated wholly or in significant part by generative AI. Future development will not use Generative AI.
There are a few older commits where I tried it for automatic refactoring, found it less than successful, and cleaned it up afterward. You can try the same thing; I wouldn't be able to tell the difference probably, but my conclusion to that experiment was that it wasn't worth it at the time.
Parts
80| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100k | PCM_4ms_Resistor:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4, R6, R8, R16, R18, R21, R22, R24, R26, R30, R33, R35 |
| 8 | 1k | PCM_4ms_Resistor:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R7, R13, R14, R15, R19, R23, R28 |
| 8 | 20k | PCM_4ms_Resistor:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R9, R10, R11, R12, R20, R27 |
| 6 | 0.1uf | PCM_4ms_Capacitor:C_Disc_P5.08mm | C5, C9, C10, C11, C12, C13 |
| 4 | D | PCM_4ms_Diode:D_DO-35_P7.62mm_Horizontal | D1, D2, D5, D6 |
| 2 | 10k | PCM_4ms_Resistor:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R17, R25 |
| 2 | 10nF | PCM_4ms_Capacitor:C_Disc_P5.08mm | C1, C4 |
| 2 | 10nf | PCM_4ms_Capacitor:C_Disc_P5.08mm | C7, C14 |
| 2 | 10uF | PCM_4ms_Capacitor:CP_Radial_P2.5mm | C2, C3 |
| 2 | 1N5817 | PCM_4ms_Diode:D_DO-41_P7.62mm_Horizontal | D3, D4 |
| 2 | 1m | PCM_4ms_Resistor:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5, R29 |
| 2 | CV_IN | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J2, J9 |
| 2 | CV_OUT | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J3, J10 |
| 2 | GATE_OUT | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J5, J11 |
| 2 | J113 | Package_TO_SOT_THT:TO-92 | Q1, Q8 |
| 2 | R_Potentiometer | mouser:RD901F4015R1B10K00DL1 | RV1, RV2 |
| 2 | SW_SPDT | mouser:200MSP1T1B1M2QE | SW1, SW2 |
| 2 | TL074 | Package_DIP:DIP-14_W7.62mm_Socket | U1, U4 |
| 2 | TRIG_OUT | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J6, J12 |
| 1 | 0.33uf | PCM_4ms_Capacitor:C_Disc_P5.08mm | C6 |
| 1 | 40106 | Package_DIP:DIP-14_W7.62mm_Socket | U2 |
| 1 | ARCADE_BTN | Connector_JST:JST_XH_S2B-XH-A-1_1x02_P2.50mm_Horizontal | SW3 |
| 1 | ARCADE_BTN_B | Connector_JST:JST_XH_S2B-XH-A-1_1x02_P2.50mm_Horizontal | SW4 |
| 1 | A_IN | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J7 |
| 1 | A_OUT | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J1 |
| 1 | B_IN | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J16 |
| 1 | B_OUT | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J17 |
| 1 | EURO_PWR_2x5 | KitsBlips:Pins_2x05_2.54mm_TH_Europower_shrouded | J4 |
| 1 | L78L05_TO92 | Package_TO_SOT_THT:TO-92_Inline | U3 |
| 1 | PANEL_A_IN | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J14 |
| 1 | PANEL_A_OUT | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J8 |
| 1 | PANEL_B_IN | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J13 |
| 1 | PANEL_B_OUT | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J15 |
More from Alloyed/KitsBlips
10- 2 layers150 × 100 mm

- 2 layers80.8 × 110 mm

- 2 layers40 × 110 mm

- 2 layers80.8 × 110 mm

- 2 layers70.7 × 21.1 mm

- 2 layers19.9 × 100 mm

- 2 layers60.5 × 100 mm

- 2 layers80.8 × 110 mm

- 2 layers70 × 100 mm

- 2 layers91 × 50 mm

Similar boards
- 2 layers20.9 × 21.2 mm

- 2 layers98 × 135 mm

- 4 layers330.2 × 304.8 mm

- 2 layers100 × 70 mm

- 2 layers61.1 × 45.8 mm

- 2 layers127 × 128.5 mm

Wow and flutter
mprosk/wow_and_flutter
Wow & Flutter is a pitch modulation source, that generates triangle and sample and hold with slew
72 parts2MIT - 2 layers48 × 120.5 mm

DMH S H Noise PCB
DeMarco/DMH-S-H-Noise
Implementation of the S&H + Noise Generator circuits by Moritz Klein into Kosmo format.
82 parts1 - 2 layers60 × 40 mm

Pi psu
grahamseamans/pi-psu
A 5V linear power supply designed for Raspberry Pi and similar devices.
21 parts
Questions
How big is the 4gates PCB?
It measures 84 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the 4gates use?
80 parts, built around the J113. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the 4gates KiCad files?
From the Alloyed/KitsBlips repository on GitHub, at the commit this page was made from: the board is kicad/ida-button/4gates.kicad_pcb and its schematic kicad/4knobs/4knobs.circuitjs.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the 4gates design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).