

Argon
ARGON - SPI NOR flash reader&writer hardware
- Size
- 62 × 62 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 78
- Nets
- 54
- Pads
- 269
- Tracks, vias
- 676, 59
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 1 Dec 2020
- Updated
- 8 Nov 2021
Overview
Argon is an open-source printed circuit board by alicjamusial, from the alicjamusial/argon repository on GitHub. It is a 2-layer board of 62 × 62 mm with 78 parts on 54 nets, routed with 676 tracks and 59 vias.
It is built around the AMS1117-3.3, FT2232HL and USBLC6-2SC6. Its parts include 25 capacitors, 20 resistors, 7 diodes, 7 connectors and 6 ICs. It belongs with the interfaces and adapters boards of this library.
Main components
3AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsFT2232HL
QFP64Dual High Speed USB to Multipurpose UART/FIFO ICFTDIUncategorisedUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
README
README.mdArgon & Benzene - SPI NOR Flash programmer & reader

◾ About the project
This project consists of two boards: Argon and Benzene.
Argon is a SPI NOR flash programmer & reader. It's based on the FT2232H microcontroller (with two UARTs - A & B). The board has three LED indicators of data - on TX, RX and CS lines and some sockets to be able to plug in the logic analyzer. Version 1.0 of Argon is available in the releases section.
Benzene is a DIP-8/DIP-16 to Argon adapter. It includes mostly a few capacitors and resistors to allow SPI flash to run smoothly. There is also a 555 timer with LED indicator on CS line goldpins to attach the logic analyzer.
Version 1.0 of Benzene is available in the releases section.
Argon works best with Benzene attached - they are designed to match each other (you can put two Benzene boards on top of the Argon). Argon can be also used separately as USB<->UART/FIFO/I2C/SPI converter (similar to FTDI Mini Module).
Both boards were designed using KiCad 5.1.6.
◾ Software
Argon software is available in this repository.
◾ Known issues
Argon 1.1
- No known issues, but wasn't assembled yet.
Benzene 1.0
- Logo is too small and illegible (not very important, so won't be fixed by now)
Project
- KiCad libraries are a bit chaotic (not very important, so won't be fixed by now)
◾ Usage examples
Argon is meant to be used as SPI NOR flash reader & writer with:
- Benzene & flash soldered to DIP-8/DIP-16 board adapter
- Benzene & flash inside DIP-8/DIP-16 adapter
- Benzene & clip with DIP-8/16 adapter to read or program flash placed on another board
It can be also used standalone as USB<->UART/FIFO/I2C/SPI converter (all FTDI Mini Module functionalities in the nicer and more readable form).
Note: all photos show Argon in version 1.0.
◾ Schematics and designs
All of them can be found in the releases section as KiCad files, gerber files, pdf and svg format.
▪️ Argon 1.1

▪️ Benzene 1.0

◾ Other hints
When assembling your own Argon or Benzene please use LED's resistors calculated for your chosen colours.
◾ License
Argon and Benzene are available on Creative Commons Attribution Share Alike 4.0 International license (more in license file). You are free to use it, modify it and produce as many of your own boards as you need :)
Parts
78| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C4, C6, C8, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24 |
| 7 | LED | benzene:LED_0805_2012Metric | D1, D2, D3, D4, D5, D6, D7 |
| 6 | V3V3-GND | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2, J3, J4, J5, J6, J7 |
| 5 | 220R | Resistor_SMD:R_0603_1608Metric | R6, R17, R18, R19, R20 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R5, R7, R9 |
| 3 | 10nF | Capacitor_SMD:C_0603_1608Metric | C2, C3, C9 |
| 3 | 4.7uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C7, C12, C13 |
| 2 | 1.5K | Resistor_SMD:R_0603_1608Metric | R1, R10 |
| 2 | 10R | Resistor_SMD:R_0603_1608Metric | R12, R13 |
| 2 | 1M | Resistor_SMD:R_0603_1608Metric | R3, R15 |
| 2 | 22uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C5, C25 |
| 2 | 27pF | Capacitor_SMD:C_0603_1608Metric | C10, C11 |
| 2 | 330R | Resistor_SMD:R_0603_1608Metric | R4, R16 |
| 2 | 600R/0.5A | FBead_Murata_BLM18AG601SN1D:Murata-BLM18-0.15-t0.8-0-0-IPC_A | FB1, FB2 |
| 2 | Connector8 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | S1, S2 |
| 2 | Connector8_FTDI | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | S3, S4 |
| 2 | LMC555xM | Package_SO:VSSOP-8_3.0x3.0mm_P0.65mm | U1, U4 |
| 1 | 120R | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 12K | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 12Mhz | Crystal:Crystal_SMD_SeikoEpson_TSX3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | 2.2K | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 93LCxxA | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | FT2232HL | Package_QFP:LQFP-64_10x10mm_P0.5mm | U5 |
| 1 | LOGO | argon:argon_logo_1_1 | G*** |
| 1 | LOGO | argon:pattern_argon | G*** |
| 1 | USB | Connector_USB:USB_Mini-B_Wuerth_65100516121_Horizontal | J1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U6 |
More from alicjamusial/argon
1- 2 layers25 × 30 mm

Similar boards
- 2 layers30 × 48 mm

Ft2232h jtag uart
thecasterian/FT2232-JTAG-UART
Dual JTAG/UART interface board using FT2232
41 partsBSD-3-Clause - 4 layers60 × 37 mm

- 4 layers50 × 50 mm

Bus Redundancy Controller
jjgarrid/Bus-Redundancy-Controller
Bus redundancy controller PoC implemented using a FPGA
87 parts2GPL-3.0 - 4 layers65 × 56.5 mm

Tangnano9k kr260-hat
calperxd/tangnano9k-kr260-hat
FPGA HAT for the AMD Kria KR260 based on the Tang Nano 9K (Gowin GW1NR-9, FT2232H, 16-bit parallel link on J21): KiCad 10 schematic, 4-layer PCB and JLCPCB production files
181 parts1 - 4 layers62.5 × 49 mm

Flash
Maka8295/FT2232H-Breakout-board
FT2232H Breakout board with level shifting and selectable io level.
76 parts1 - 4 layers

- 4 layers180 × 160 mm

PCE colorlight carrier
supermomo31/PCE_colorlight_carrier
console PCE depuis un FPGA format SODIMM : colorlight i5
258 parts - 4 layers115 × 85 mm

Questions
How big is the Argon PCB?
It measures 62 × 62 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Argon use?
78 parts, built around the AMS1117-3.3, FT2232HL and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Argon KiCad files?
From the alicjamusial/argon repository on GitHub, at the commit this page was made from: the board is argon/argon.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Argon design in my own project?
Its repository states no licence, so its author keeps all rights: ask alicjamusial before reusing the design.