Skip to the content
2 layers20.6 × 28 mmSoundDropUNIT, the printed circuit board in 3D

SoundDropUNIT

Size
20.6 × 28 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
19
Pads
39
Tracks, vias
67, 2
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
21 Dec 2024
Updated
9 Apr 2026

Overview

SoundDropUNIT is an open-source printed circuit board by akita11, from the akita11/SoundDropUNIT repository on GitHub, published under the MIT licence. It is a 2-layer board of 20.6 × 28 mm with 12 parts on 19 nets, routed with 67 tracks and 2 vias.

Its parts include 4 connectors, 3 resistors and 1 diode.

README

README.md

SoundDropUNIT

音声再生IC JQ8400を使用した音声再生モジュールです。4MBのフラッシュメモリを搭載しており、PCにmicroUSBケーブルで接続するとUSBメモリとして認識され、そこにMP3音声データ等をコピーします。その音声データをGrove端子のシリアル(UART)通信で再生制御できます。UIFlow(v1)用のブロックもあります。

※JQ8400に関する情報はWebページ等で検索してください。例えばaitendoのモジュールがあります。

使い方(接続方法)

以下のようにスピーカやアンプを接続し、Grove端子からの制御で音声を再生します。

アンプ付きスピーカに接続する場合

3.5mmジャック(ステレオ:上部中央)に3.5mmステレオケーブル等でアンプに接続します。

スピーカを直接接続する場合

基板上部にある1.25mmピッチコネクタ(Molex 53047-0210用)をとりつける端子があり、市販の小型スピーカ(M5Stack本体に使われているものなど。AliExpressやTaobaoでも同等品があります)を接続することができます。※隙間がせまく差し込みにくいので注意してください。

3.5mmジャックに直接スピーカを接続する方法

3.5mmジャックに直接スピーカを接続することもできます。その場合は、基板裏面のハンダジャンパを以下のように修正してください。(スピーカはモノラル再生となります) ※結線は、プラグの根本側から、GND-SPK-NC(無接続)、の順となります。そのため、ステレオ型スピーカではL側からの再生になります。またモノラルプラグでは、このGNDとSPKが短絡されるため使用できません。

  • JP1をカット
  • JP2・JP3の中央と△マーク側をカットし、中央と反対側(△マークがない側)をショート

使い方(ソフトウエア)

あらかじめ、本体のmicroUSBコネクタにmicroUSBケーブルを使ってPCへ接続し、現れるドライブに使用する音声データ(*.mp3等)をコピーしておきます。(このときコピーした順番が、再生時に使用する「曲番号」になります)

UIFlow(v1)での使い方

「SoundDrop.m5b」をダウンロードし、UIFlow(v1)の"Custom"の"Open *.m5b"からこのファイルを指定すると、Init、Play、Stopの3つのブロックを使用できます。

  • SoundDrop_Init : 初期化。最初に1回だけ読み出します。"TX"と"RX"には、使用するGroveポート・マイコン本体にあわせて、使用するピン番号を指定します。例えば、M5StackBasicのPortA(本体の赤いコネクタ)の場合は、上図のようにTX=21、RX=22を指定します。M5StackCore2のPortAの場合は、TX=32、RX=33となります。
  • SoundDrop_Play : numに指定した「曲番号」の音声を再生します。
  • SoundDrop_Stop : 再生中の音声を停止します。

その他のソフトウエアでの使い方

搭載されている音声再生IC(JQ8400)のデータシート等を参考に、制御コマンドを送信して使用してください。 Arduino用にはライブラリがあるようなので、そちらを使ってもOKです。

Author

Junichi Akita (@akita11) / akita@ifdl.jp

Parts

12
QtyValueFootprintReferences
31kResistor_SMD:R_0603_1608MetricR1, R2, R3
2Jumper_2_BridgedJumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mmJP1, JP2
2SolderJumper_3_Bridged12Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mmJP3, JP4
1AudioJack2_Ground_Switchakita:CON_AJ-1780J3
1CON_GROVEakita:CON_GROVE_HCN1
1Conn_01x02Connector_Molex:Molex_PicoBlade_53047-0210_1x02_P1.25mm_VerticalJ2
1Conn_01x10Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_VerticalJ1
1LEDLED_SMD:LED_0603_1608MetricD1

Similar boards

  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915
  • 2 layers28.3 × 10.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    12 parts716GPL-3.0
  • 2 layers25.4 × 70.4 mmTpmsniffer, the printed circuit board in 3D

    Tpmsniffer

    stacksmashing/pico-tpmsniffer

    A simple, very experimental TPM sniffer for LPC bus

    12 parts696

Questions

How big is the SoundDropUNIT PCB?

It measures 20.6 × 28 mm and has 2 copper layers, 1.6 mm thick.

What parts does the SoundDropUNIT use?

12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the SoundDropUNIT KiCad files?

From the akita11/SoundDropUNIT repository on GitHub, at the commit this page was made from: the board is SoundDropUNIT.kicad_pcb and its schematic SoundDropUNIT.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the SoundDropUNIT design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).