
Type e
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

DFPlayeProUNIT
DFPlayerProUNIT is an open-source printed circuit board by akita11, from the akita11/DFPlayerProUNIT repository on GitHub, published under the MIT licence. It is a 2-layer board of 22.9 × 31.8 mm with 16 parts on 20 nets, routed with 134 tracks and 4 vias.
Its parts include 10 connectors and 2 resistors.
DFRobotの音声プレーヤモジュールDFPlayer ProをGrove端子を接続して制御できるモジュールです。Grove端子からシリアル(UART)通信で音声再生などを制御することができます。(UIFlow(v1)用のブロックも用意する予定)
※DFPlayerProは付属していません
以下のようにスピーカやアンプを接続し、Grove端子からの制御で音声を再生します。また基板上の"PAYE"と"KEY"のシルクが示されている2組の端子は、それぞれDFPlayerProのKEY、PLAY端子に接続されていますので、これらを使って再生を制御することもできます(詳細はDFPlayerProのマニュアルを参照してください)
3.5mmジャック(ステレオ:上部中央)に3.5mmステレオケーブル等でアンプに接続します。
本体上部の2つの2.54mmた端子にスピーカを接続します。spkLとspkRがそれぞれお左と右のスピーカです。基板中央部に1.25mmピッチコネクタ(Molex 53047-0210用)をとりつける端子があり、市販の小型スピーカ(M5Stack本体に使われているものなど。AliExpressやTaobaoでも同等品があります)を接続することができます。
3.5mmジャックに直接スピーカを接続することもできます。その場合は、基板裏面のハンダジャンパを以下のように修正してください。
あらかじめ、DFPlayerProをUSB Type-Cケーブルを使ってPCへ接続し、現れるドライブに使用する音声データ(*.mp3等)をコピーしておきます。(このときコピーした順番が、再生時に使用する「曲番号」になります)
「DFPlayerPro.m5b」をダウンロードし、UIFlow(v1)の"Custom"の"Open *.m5b"からこのファイルを指定すると、Init、Play、Volumeの3つのブロックを使用できます。
Arduino用にはライブラリがあるようなので、そちらを使ってもOKです。 あるいは、DFPlayerProのデータシート等を参考に、制御コマンドを送信して使用してください。
Junichi Akita (@akita11) / akita@ifdl.jp
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J4, J5, J6, J7 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | Conn_01x02 | Connector_Molex:Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J8, J9 |
| 2 | Conn_01x06 | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J1, J2 |
| 2 | Jumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | JP1, JP2 |
| 2 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm | JP3, JP4 |
| 1 | AudioJack2_Ground_Switch | akita:CON_AJ-1780 | J3 |
| 1 | CON_GROVE | akita:CON_GROVE_H | CN1 |

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

conorpp/u2f-zero
U2F USB token optimized for physical security, affordability, and style

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!


It measures 22.9 × 31.8 mm and has 2 copper layers, 1.6 mm thick.
16 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the akita11/DFPlayerProUNIT repository on GitHub, at the commit this page was made from: the board is DFPlayerProUNIT.kicad_pcb and its schematic DFPlayerProUNIT.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).