Skip to the content
2 layers74 × 39 mmMain pcb ui, the printed circuit board in 3D

Moduar LED light painting strip with 180 LEDs per meter

Size
74 × 39 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
10
Pads
54
Tracks, vias
59, 0
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
27 Jun 2021
Updated
1 Jun 2024

Overview

Main pcb ui is an open-source printed circuit board by akaFunk, from the akaFunk/BlinkyBar repository on GitHub, published under the CC-BY-4.0 licence. It is a 2-layer board of 74 × 39 mm with 17 parts on 10 nets, routed with 59 tracks and 0 vias.

Its parts include 6 resistors, 6 switches, 4 connectors and 1 diode.

README

README.md

BlinkyBar

The BlinkyBar is a modular LED light painting device based on the WS2812B programmable RGB LEDs. It features modules with a length of approximately 250mm, which can be attached to a host module of an arbitrary length. The host module holds a Raspberry Pi Zero W, which provides access to the device with a Wifi access point. A website running on the Raspi allows to upload an image. Once the trigger button on the host module is pressed, the image is played back one column after another. Combining this with a long time expose will paint the uploaded image into thin air.

We are currently working on the first release. Images made with an earlier version are shown below. This older version featured only 60 LEDs per meter, while the new one will have 180 LEDs per meter.

Images

Examples of the old version: Example Image 1 Example Image 2

3D rendering of the current main module: Example Image 1 Example Image 1

Images of the first prototype: Example Image 1 Example Image 1 Example Image 1 Example Image 1

Building BlinkyBar

Issues to be aware of

BlinkyBar is still in development and there are currently a few issues, which are important to note if you want to build it. They will be addressed in the future:

  • The 1117 LDO is not working with the currently populated MLCC output capacitors. Their ESR is too low. You will hear an annoying high pitch tone and have a ~400 mVpp triangle on the output voltage. Either replace the output capacitors with Aluminium Electrolytic types, solder a 0.5 Ohm resistor in series with the capacitors, or use a different LDO (for example BL8071CLBTR33 or AP2114H-3.3TRG1). Currently we have tested only using the Aluminium Electrolytic caps which works fine.
  • The modules are not able to power down automatically if the host module powers down. Please make sure to remove the batteries, otherwise they will be empty after some time. However, the battery under-voltage protection should work for both the host and the modules, so your batteries are safe.

Parts

Additional part required for a BlinkyBar with 4 modules and the main unit, i.e., 10 module PCBs and a length of 2475 mm and 450 LEDs. For the PCBs you will find lists in CSV format exported from KiCad in each of the PCBs output folder.

DescriptionCount3D Model
U-Profile, 30x20x2x495 mm (WxHxTxL), Aluminum1main_profile
U-Profile, 30x20x2x495 mm (WxHxTxL), Aluminum4module_profile
6x6x100 mm, Steel8module_bolt
3D-printed stand for the module PCB15module_stand
3D-printed power button protector1main_button_protector
3D-printed main case1main_case
3D-printed handle1main_handle
18650 Holder1218650_holder
Plate, 35x25x3 mm, Steel4module_plate
Main PCB holding the Raspberry Pi Zero and the user interface PCB1main_pcb
Main PCB adapter to combine and raise the two connector fro the module pcb within the main module1main_pcb_adapter
Main PCB front panel as the case cover1main_pcb_front
Main PCB user interface holding a few buttons and an LED1main_pcb_ui
Module PCB with the LEDs10module_pcb
M4x12 wing screw (DIN 316)4
M3x5 flat head screw (ISO7380) to hold the case to the profile2
M3x4 countersunk head screw (ISO 14581) to hold the battery holders24
M3 nut (ISO 4032) to hold the battery holders in the main case4
M3x8 flat head screw (ISO7380) to hold the main PCB in the case4
M3 nut (ISO 4032) to hold the main PCB in the case4
M3x20 flat head screw (ISO7380) to hold the front panel PCB to the case4
M3 nut (ISO 4032) to hold the front panel PCB to the case4
M3x12 flat head screw (ISO7380) to hold the stand to the profile28
M3x20 flat head screw (ISO7380) to hold the handle and two of the stands to the profile2
M3 nut (ISO 4032) to hold the stand to the profile30
M3x8 flat head screw (ISO7380) to hold the module PCB to the stand60
M3 nut (ISO 4032) to hold the module PCB to the stand60
M2x5 flat head screw (ISO7380) to hold the power button protector to the front panel PCB2
M2 nut (ISO 4032) to hold the power button protector to the front panel PCB2
M3x8 flat head screw (ISO7380) to hold the steel bolts to the profile16

Replacement parts

Some MPN in the CSV/schematics are just some random ones, for example for pin headers, which fit and were available at the time of design. Those may be replaced with similar types. A (bar far not complete) list of such parts is given below:

PartDescriptionReplacements

TODO/Further development

  • Make everything much simpler, especially the bus topology, mechanical design, and power design
  • Use smaller LEDs, for example SK6805-EC15, and increase LED density

Parts

17
QtyValueFootprintReferences
51kResistor_SMD:R_0603_1608MetricR2, R3, R4, R5, R6
4Conn_02x02_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x02_P2.54mm_VerticalJ1, J2, J3, J4
2SP+Button_Switch_THT:SW_PUSH_6mm_H8mmSW1, SW6
1220Resistor_SMD:R_0603_1608MetricR1
1BR+Button_Switch_THT:SW_PUSH_6mm_H8mmSW4
1BR-Button_Switch_THT:SW_PUSH_6mm_H8mmSW5
1LEDLED_THT:LED_D3.0mmD1
1SP-Button_Switch_THT:SW_PUSH_6mm_H8mmSW2
1TRIGButton_Switch_THT:SW_PUSH_6mm_H8mmSW3

More from akaFunk/BlinkyBar

3
  • 2 layers247.5 × 25 mmModule pcb, the printed circuit board in 3D

    Module pcb

    akaFunk/BlinkyBar

    Moduar LED light painting strip with 180 LEDs per meter

    106 parts1CC-BY-4.0
  • 2 layers95 × 95 mmMain pcb, the printed circuit board in 3D

    Main pcb

    akaFunk/BlinkyBar

    Moduar LED light painting strip with 180 LEDs per meter

    52 parts1CC-BY-4.0
  • 2 layers20 × 25 mmMain pcb adapter, the printed circuit board in 3D

    Main pcb adapter

    akaFunk/BlinkyBar

    Moduar LED light painting strip with 180 LEDs per meter

    3 parts1CC-BY-4.0

Similar boards

  • 2 layers50 × 35 mmServo power, the printed circuit board in 3D

    Servo power

    earthtojake/text-to-cad

    Design physical products with AI

    17 parts26kMIT
  • 2 layers139.7 × 62.2 mmBreakout 60pin EEC IV, the printed circuit board in 3D

    Breakout 60pin EEC IV

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    17 parts1.2k
  • 2 layers29.2 × 55.9 mmDeniseadapter, the printed circuit board in 3D

    Deniseadapter

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    17 parts1kGPL-3.0
  • 2 layers24.5 × 36.5 mmCluster, the printed circuit board in 3D

    Cluster

    JesusFreke/lalboard

    A 3D-printed keyboard inspired by the DataHand

    17 parts993
  • 2 layers56.3 × 55.7 mmStarNecklace, the printed circuit board in 3D

    StarNecklace

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    17 parts915
  • 2 layers25 × 25 mmSmallEncoder, the printed circuit board in 3D

    SmallEncoder

    DDeGonge/OS-ARM

    This arm is not industrial and it will not be fast, but that is not my goal. But it will hopefully be a very nice looking arm fully capable of 6dof motion, cheap enough to keep it accessable but capable enough to…

    17 parts498MIT
  • 2 layers38.9 × 16.1 mmAmoeba spc, the printed circuit board in 3D

    Amoeba spc

    mtl/keyboard-pcbs

    Keyboard PCBs

    17 parts485
  • 2 layers36 × 51 mmABSIS ALE, the printed circuit board in 3D

    ABSIS ALE

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    17 parts431

Questions

How big is the Main pcb ui PCB?

It measures 74 × 39 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Main pcb ui use?

17 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Main pcb ui KiCad files?

From the akaFunk/BlinkyBar repository on GitHub, at the commit this page was made from: the board is main_pcb_ui/main_pcb_ui.kicad_pcb and its schematic main_pcb/main_pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Main pcb ui design in my own project?

Its repository publishes it under the CC-BY-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).