Skip to the content
2 layers85.9 × 59.5 mmElec2133 bonus, the printed circuit board in 3D

KiCad PCB design for a Signal Generator

Size
85.9 × 59.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
28
Nets
27
Pads
84
Tracks, vias
178, 0
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
16 Oct 2026
Updated
16 Oct 2026

Overview

Elec2133 bonus is an open-source printed circuit board by ahabiqbal08, from the ahabiqbal08/PCB-Design repository on GitHub. It is a 2-layer board of 85.9 × 59.5 mm with 28 parts on 27 nets, routed with 178 tracks and 0 vias.

Its parts include 12 resistors, 5 capacitors, 4 ICs and 3 connectors.

README

README.md

ELEC2133 Signal Generator

A two-layer through-hole PCB that generates a square wave, converts it to a triangle wave, and then to an approximately sine wave, using four LM741 op-amps. Designed in KiCad 10.

Author: Ahab Iqbal Date: July 2026


How it works

The circuit is a chain of four op-amp stages. Each stage feeds the next.

text
 Relaxation      Lossy            Lossy            Inverting
 oscillator  ->  integrator   ->  integrator   ->  amplifier
   (U1)            (U2)             (U3)             (U4)
  square         triangle          ~sine         output stage
StageICFunctionKey components
1U1Square wave – astable (relaxation) oscillator with positive feedbackR1 = 100k, C1 = 10 nF (timing); R2 = 100k, R3 = 27k (threshold divider)
2U2Triangle wave – integrates the square waveR4 = 10k input; C2 = 100 nF with R5 = 100k in parallel as feedback; R6 = 10k bias resistor
3U3Sine-like wave – integrates and smooths the triangleR7 = 10k input; C3 = 10 nF with R9 = 100k in parallel as feedback; R8 = 10k bias resistor
4U4Output amplifier – inverting gain stageR10 = 10k input, R12 = 27k feedback (gain ≈ −2.7); R11 = 10k bias resistor

Each op-amp has a trimmer (RV1–RV4) across its offset-null pins (1 and 5), with the wiper tied to −15 V. This is the standard LM741 offset adjustment.

Expected frequency

From the component values, the oscillator in stage 1 should run at roughly 1.16 kHz:

text
beta = R3 / (R2 + R3) = 27k / 127k ≈ 0.213
f    = 1 / (2 · R1 · C1 · ln((1 + beta) / (1 − beta))) ≈ 1.16 kHz

This is a theoretical estimate that assumes an ideal op-amp and symmetric output saturation. Measured values will differ because of component tolerances and the 741's slew rate.


Power

The board needs a dual supply of ±15 V.

ConnectorNetNotes
J1+15 V2-pin header (both pins tied together)
J2GND2-pin header (both pins tied together)
J3−15 V2-pin header (both pins tied together)

C4 (100 nF, +15 V to GND) and C5 (100 nF, GND to −15 V) provide supply decoupling.


Taking measurements

WaveformProbe point
SquareU1 pin 6
TriangleU2 pin 6
Sine-likeU3 pin 6
Final output (inverted, amplified sine)U4 pin 6

Use any GND pin on J2 as the reference.


Bill of materials

RefValueQtyFootprint
U1–U4LM7414DIP-8 (7.62 mm)
R1, R2, R5, R9100k4Axial DIN0207, 10.16 mm pitch
R4, R6, R7, R8, R10, R1110k6Axial DIN0207, 10.16 mm pitch
R3, R1227k2Axial DIN0207, 10.16 mm pitch
C1, C310 nF (0.01 µF)2Disc, 5.0 mm dia, 2.5 mm pitch
C2100 nF (0.1 µF)1Disc, 5.0 mm dia, 2.5 mm pitch
C4, C5100 nF2Disc, 5.0 mm dia, 2.5 mm pitch
RV1–RV4Potentiometer (value not specified in schematic)4Bourns 3296W vertical
J1–J31×2 pin header32.54 mm, vertical SMD

Repository contents

text
elec2133_bonus/
├── elec2133_bonus.kicad_pro      KiCad project file
├── elec2133_bonus.kicad_sch      Schematic
├── elec2133_bonus.kicad_pcb      PCB layout
├── elec2133_bonus.kicad_prl      Local project settings
├── ERC.rpt                       Electrical rules check report (0 errors, 0 warnings)
├── elec2133_bonus-*.gbr          Gerber files (copper, mask, paste, silkscreen, edge cuts)
├── elec2133_bonus-PTH.drl        Plated drill file
├── elec2133_bonus-NPTH.drl       Non-plated drill file
├── elec2133_bonus-job.gbrjob     Gerber job file
└── .history/                     KiCad local history (automatic snapshots)

Board specifications

PropertyValue
Layers2 (F.Cu / B.Cu)
Thickness1.6 mm
Size≈ 85.9 × 59.6 mm
Min track width / clearance0.2 mm / 0.2 mm

Parts

28
QtyValueFootprintReferences
610kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4, R6, R7, R8, R10, R11
4100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2, R5, R9
4LM741Package_DIP:DIP-8_W7.62mmU1, U2, U3, U4
4R_PotentiometerPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV1, RV2, RV3, RV4
3Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical_SMD_Pin1RightJ1, J2, J3
20.01uCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC1, C3
2100nCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC4, C5
227kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R12
10.1uCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC2

Similar boards

  • 2 layers44.5 × 72.7 mmOSO SWAT C1-jig, the printed circuit board in 3D

    OSO SWAT C1-jig

    joeycastillo/Sensor-Watch

    A board replacement for the classic Casio F-91W wristwatch

    28 parts2.1k
  • 2 layers95 × 54 mmEinkPDA screen, the printed circuit board in 3D

    EinkPDA screen

    TalismanDesign/PocketMage_PDA

    An E-Ink PDA device using the ESP32 S3.

    28 parts2kApache-2.0
  • 2 layers45 × 45 mmSmartbuttons, the printed circuit board in 3D

    Smartbuttons

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    28 parts915
  • 2 layers24.1 × 36.2 mmEsp32miniBT, the printed circuit board in 3D

    Esp32miniBT

    asterics/esp32_mouse_keyboard

    ESP32 implementation for HID over GATT Keyboard and Mouse (Bluetooth Low Energy). Including serial API for external modules (similar to Adafruit EZKey HID)

    28 parts911GPL-3.0
  • 2 layers34.8 × 12.2 mmInfnoise goldfingers, the printed circuit board in 3D

    Infnoise goldfingers

    waywardgeek/infnoise

    The world's easiest TRNG to get right

    28 parts854CC0-1.0
  • 2 layers55.9 × 99.1 mmStm32f0 disco Luos shield, the printed circuit board in 3D

    Stm32f0 disco Luos shield

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    28 parts546MIT
  • 2 layers88 × 25 mmEleLab v2 Frontpanel a, the printed circuit board in 3D

    EleLab v2 Frontpanel a

    Chrismettal/EleLab_v2

    Cheap DIY lab system for hobbyists and the tinkering folk

    28 parts531GPL-3.0

Questions

How big is the Elec2133 bonus PCB?

It measures 85.9 × 59.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Elec2133 bonus use?

28 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Elec2133 bonus KiCad files?

From the ahabiqbal08/PCB-Design repository on GitHub, at the commit this page was made from: the board is elec2133_bonus.kicad_pcb and its schematic elec2133_bonus.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Elec2133 bonus design in my own project?

Its repository states no licence, so its author keeps all rights: ask ahabiqbal08 before reusing the design.