
OSO SWAT C1-jig
joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch

KiCad PCB design for a Signal Generator
Elec2133 bonus is an open-source printed circuit board by ahabiqbal08, from the ahabiqbal08/PCB-Design repository on GitHub. It is a 2-layer board of 85.9 × 59.5 mm with 28 parts on 27 nets, routed with 178 tracks and 0 vias.
Its parts include 12 resistors, 5 capacitors, 4 ICs and 3 connectors.
A two-layer through-hole PCB that generates a square wave, converts it to a triangle wave, and then to an approximately sine wave, using four LM741 op-amps. Designed in KiCad 10.
Author: Ahab Iqbal Date: July 2026
The circuit is a chain of four op-amp stages. Each stage feeds the next.
Relaxation Lossy Lossy Inverting
oscillator -> integrator -> integrator -> amplifier
(U1) (U2) (U3) (U4)
square triangle ~sine output stage| Stage | IC | Function | Key components |
|---|---|---|---|
| 1 | U1 | Square wave – astable (relaxation) oscillator with positive feedback | R1 = 100k, C1 = 10 nF (timing); R2 = 100k, R3 = 27k (threshold divider) |
| 2 | U2 | Triangle wave – integrates the square wave | R4 = 10k input; C2 = 100 nF with R5 = 100k in parallel as feedback; R6 = 10k bias resistor |
| 3 | U3 | Sine-like wave – integrates and smooths the triangle | R7 = 10k input; C3 = 10 nF with R9 = 100k in parallel as feedback; R8 = 10k bias resistor |
| 4 | U4 | Output amplifier – inverting gain stage | R10 = 10k input, R12 = 27k feedback (gain ≈ −2.7); R11 = 10k bias resistor |
Each op-amp has a trimmer (RV1–RV4) across its offset-null pins (1 and 5), with the wiper tied to −15 V. This is the standard LM741 offset adjustment.
From the component values, the oscillator in stage 1 should run at roughly 1.16 kHz:
beta = R3 / (R2 + R3) = 27k / 127k ≈ 0.213
f = 1 / (2 · R1 · C1 · ln((1 + beta) / (1 − beta))) ≈ 1.16 kHzThis is a theoretical estimate that assumes an ideal op-amp and symmetric output saturation. Measured values will differ because of component tolerances and the 741's slew rate.
The board needs a dual supply of ±15 V.
| Connector | Net | Notes |
|---|---|---|
| J1 | +15 V | 2-pin header (both pins tied together) |
| J2 | GND | 2-pin header (both pins tied together) |
| J3 | −15 V | 2-pin header (both pins tied together) |
C4 (100 nF, +15 V to GND) and C5 (100 nF, GND to −15 V) provide supply decoupling.
| Waveform | Probe point |
|---|---|
| Square | U1 pin 6 |
| Triangle | U2 pin 6 |
| Sine-like | U3 pin 6 |
| Final output (inverted, amplified sine) | U4 pin 6 |
Use any GND pin on J2 as the reference.
| Ref | Value | Qty | Footprint |
|---|---|---|---|
| U1–U4 | LM741 | 4 | DIP-8 (7.62 mm) |
| R1, R2, R5, R9 | 100k | 4 | Axial DIN0207, 10.16 mm pitch |
| R4, R6, R7, R8, R10, R11 | 10k | 6 | Axial DIN0207, 10.16 mm pitch |
| R3, R12 | 27k | 2 | Axial DIN0207, 10.16 mm pitch |
| C1, C3 | 10 nF (0.01 µF) | 2 | Disc, 5.0 mm dia, 2.5 mm pitch |
| C2 | 100 nF (0.1 µF) | 1 | Disc, 5.0 mm dia, 2.5 mm pitch |
| C4, C5 | 100 nF | 2 | Disc, 5.0 mm dia, 2.5 mm pitch |
| RV1–RV4 | Potentiometer (value not specified in schematic) | 4 | Bourns 3296W vertical |
| J1–J3 | 1×2 pin header | 3 | 2.54 mm, vertical SMD |
elec2133_bonus/
├── elec2133_bonus.kicad_pro KiCad project file
├── elec2133_bonus.kicad_sch Schematic
├── elec2133_bonus.kicad_pcb PCB layout
├── elec2133_bonus.kicad_prl Local project settings
├── ERC.rpt Electrical rules check report (0 errors, 0 warnings)
├── elec2133_bonus-*.gbr Gerber files (copper, mask, paste, silkscreen, edge cuts)
├── elec2133_bonus-PTH.drl Plated drill file
├── elec2133_bonus-NPTH.drl Non-plated drill file
├── elec2133_bonus-job.gbrjob Gerber job file
└── .history/ KiCad local history (automatic snapshots)| Property | Value |
|---|---|
| Layers | 2 (F.Cu / B.Cu) |
| Thickness | 1.6 mm |
| Size | ≈ 85.9 × 59.6 mm |
| Min track width / clearance | 0.2 mm / 0.2 mm |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4, R6, R7, R8, R10, R11 |
| 4 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R5, R9 |
| 4 | LM741 | Package_DIP:DIP-8_W7.62mm | U1, U2, U3, U4 |
| 4 | R_Potentiometer | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1, RV2, RV3, RV4 |
| 3 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical_SMD_Pin1Right | J1, J2, J3 |
| 2 | 0.01u | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C1, C3 |
| 2 | 100n | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C4, C5 |
| 2 | 27k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R12 |
| 1 | 0.1u | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C2 |

joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch

TalismanDesign/PocketMage_PDA
An E-Ink PDA device using the ESP32 S3.

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

asterics/esp32_mouse_keyboard
ESP32 implementation for HID over GATT Keyboard and Mouse (Bluetooth Low Energy). Including serial API for external modules (similar to Adafruit EZKey HID)


Luos-io/luos_engine
Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

Chrismettal/EleLab_v2
Cheap DIY lab system for hobbyists and the tinkering folk
It measures 85.9 × 59.5 mm and has 2 copper layers, 1.6 mm thick.
28 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ahabiqbal08/PCB-Design repository on GitHub, at the commit this page was made from: the board is elec2133_bonus.kicad_pcb and its schematic elec2133_bonus.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ahabiqbal08 before reusing the design.