
Headlights LEDs
AdinAck/Headlights-Hardware
PCB/Mech design files for my headlights project.

PCB/Mech design files for my headlights project.
Headlights Driver is an open-source printed circuit board by AdinAck, from the AdinAck/Headlights-Hardware repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 45.2 × 35.6 mm with 62 parts on 58 nets, routed with 113 tracks and 73 vias.
It is built around the BSC190N12NS3 G. Its parts include 24 capacitors, 15 resistors, 9 connectors, 3 ICs and 3 diodes. It belongs with the STM32 boards of this library.
This repo contains the PCB design files for the headlights board.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100n | Capacitor_SMD:C_0402_1005Metric | C2, C4, C6, C14, C15, C16 |
| 5 | 100n | Capacitor_SMD:C_1206_3216Metric | C17, C20, C21, C23, C25 |
| 5 | 1u | Capacitor_SMD:C_0402_1005Metric | C1, C3, C5, C10, C12 |
| 4 | 330 | Resistor_SMD:R_0402_1005Metric | R3, R4, R5, R6 |
| 3 | 10p | Capacitor_SMD:C_0402_1005Metric | C9, C11, C13 |
| 3 | 1u | Capacitor_SMD:C_2220_5650Metric | C19, C22, C24 |
| 2 | 10 | Resistor_SMD:R_0402_1005Metric | R8, R9 |
| 2 | 10n | Capacitor_SMD:C_0402_1005Metric | C7, C8 |
| 2 | 1k96 | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 310m | Diode_SMD:D_SOD-523 | D1, D2 |
| 2 | ? | Resistor_SMD:R_0402_1005Metric | R12, R13 |
| 2 | BSC190N12NS3G | Package_TO_SOT_SMD:TDSON-8-1 | Q1, Q2 |
| 2 | M3 | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2 |
| 1 | 1 | Fuse:Fuse_0402_1005Metric | F1 |
| 1 | 1 | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 1 | Resistor_SMD:R_1206_3216Metric | R10 |
| 1 | 100u | Inductor_SMD:L_Bourns-SRN8040_8x8.15mm | L1 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | TH1 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 220 | Resistor_SMD:R_0402_1005Metric | R14 |
| 1 | 33m | Resistor_SMD:R_1206_3216Metric | R11 |
| 1 | GND | Connector_Wire:SolderWirePad_1x01_SMD_4x6mm | J2 |
| 1 | INA199A2DCKR | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U2 |
| 1 | LED+ | Connector_Wire:SolderWirePad_1x01_SMD_4x6mm | J8 |
| 1 | LED- | Connector_Wire:SolderWirePad_1x01_SMD_4x6mm | J9 |
| 1 | LOGO | Symbol:Adin_Logo_Small | G*** |
| 1 | RX | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | J6 |
| 1 | Red | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | STM32F031K6Ux | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U1 |
| 1 | SWD | Connector_Harwin:M50-3600542 | J3 |
| 1 | TX | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | J5 |
| 1 | UCC2782Q1DRC | Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.65x2.4mm_ThermalVias | U3 |
| 1 | VDD | Connector_Wire:SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm | J4 |
| 1 | VS | Connector_Wire:SolderWirePad_1x01_SMD_4x6mm | J1 |
| 1 | Vdrive | Connector_Wire:SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm | J7 |

AdinAck/Headlights-Hardware
PCB/Mech design files for my headlights project.

freudenthal/skidl-eda
skidl-eda: AI circuit-design loop harness on the skidl stack

dojoe/Twonkie
A USB-PD sniffer/injector/sink based on Google's Twinkie, re-designed to be manufactured by mere mortals.





themainframe/5g-m2-usb3-interface-pcb
KiCad EDA Project for my 5G M.2 (NGFF) USB3 Interface board

It measures 45.2 × 35.6 mm and has 4 copper layers, 1.6 mm thick.
62 parts, built around the BSC190N12NS3 G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the AdinAck/Headlights-Hardware repository on GitHub, at the commit this page was made from: the board is Headlights_Driver/Headlights_Driver.kicad_pcb and its schematic Headlights_Driver/Headlights_Driver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).