Skip to the content
2 layersPRY3, the printed circuit board in 3D

Projects covering introduction to electronic components and systems

Copper layers
2
Thickness
1.6 mm
Parts
6
Nets
5
Pads
13
Tracks, vias
28, 3
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
27 Mar 2026
Updated
9 May 2026

Overview

PRY3 is an open-source printed circuit board by adefolayigakanyinsola-dot, from the adefolayigakanyinsola-dot/Basic-electronics repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board with 6 parts on 5 nets, routed with 28 tracks and 3 vias.

Its parts include 3 resistors, 1 diode and 1 transistor.

README

README.md

Basic-electronics

Projects covering introduction to electronic components and systems

Touch Enabled Circuit Design

A non microcontroller electronics project that lights up the LED when two insulated wires touch each other at the same time.

Project Description

It is a simple project built on a breadboard. When two bare wires which serves as connectors are touched at the same time, a small amount of elevtricity passes through the skin due to low conductivity and high resistance. This in turn causes the transisitor to come on. The transistor then produces a large current from the base and battery combined which triggers the flow of current from the collector to the emitter.Then the current is passed into the LED to turn it on.

Screenshot 2026-05-05 154541

INSTALLATION PROCESS

Software - KICAD

After creating a new file and nameing the circuit design,draw the schematics. To do this,click on the component symbol icon on the top right icon bar to the side and select the components. Use the mouse to drag and connect the wires accordingly. Assign footprints by using the upper ico to the right on the menu bar or left click the mouse on each component,then navigate to footprints to check for suitable type of footprint component.

PCB LAYOUT

Open the PCB bar by clicking on the default icon which is top right to the extreme,it takes you to thr layout that has all the components layout in PCB. Using edge cuts in the apperance icon to the right,draw the small board outline enough to cover the circuit. Arrange the components and usd the route signals to connect them Using the view icon in the top left icon on the menu bar,check the 3D layout.

Parts

6
QtyValueFootprintReferences
1100KResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P1.90mm_VerticalR2
1470Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P1.90mm_VerticalR3
19VBattery:BatteryHolder_MYOUNG_BS-07-A1BJ001_CR2032BT1
1BCV547Package_TO_SOT_SMD:SOT-89-3Q1
1LDR03OptoDevice:R_LDR_10x8.5mm_P7.6mm_VerticalR1
1LEDLED_THT:LED_D2.0mm_W4.0mm_H2.8mm_FlatTopD1

More from adefolayigakanyinsola-dot/Basic-electronics

2
  • 2 layers61 × 50 mmPRY 1, the printed circuit board in 3D

    PRY 1

    adefolayigakanyinsola-dot/Basic-electronics

    Projects covering introduction to electronic components and systems

    5 partsApache-2.0
  • 2 layersPRY2, the printed circuit board in 3D

    PRY2

    adefolayigakanyinsola-dot/Basic-electronics

    Projects covering introduction to electronic components and systems

    5 partsApache-2.0

Similar boards

  • 2 layers18.5 × 11.1 mmSwitch, the printed circuit board in 3D

    Switch

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    6 parts4.3kMIT
  • 2 layers14.6 × 33 mmBrain board SD Card 1, the printed circuit board in 3D

    Brain board SD Card 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    6 parts1.2k
  • 2 layers9 × 9 mmDpoint, the printed circuit board in 3D

    Dpoint

    Jcparkyn/dpoint

    Open-source digital stylus using camera tracking and inertial measurements

    6 parts1.1kMIT
  • 2 layers51.5 × 16.6 mmMicroswitchXY Endstop, the printed circuit board in 3D

    MicroswitchXY Endstop

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    6 parts1.1kGPL-3.0
  • 2 layers21.9 × 76.7 mmAmiga External, the printed circuit board in 3D

    Amiga External

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    6 parts1kGPL-3.0
  • 2 layers88.9 × 50.8 mmBusinesscard, the printed circuit board in 3D

    Businesscard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    6 parts915
  • 2 layers20.3 × 15.2 mmL0 RGB led, the printed circuit board in 3D

    L0 RGB led

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    6 parts546MIT
  • 2 layers9 × 3.6 mmOpticalEncoder, the printed circuit board in 3D

    OpticalEncoder

    adamb314/ServoProject

    Getting the most out of your hobby servo

    6 parts545

Questions

What parts does the PRY3 use?

6 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PRY3 KiCad files?

From the adefolayigakanyinsola-dot/Basic-electronics repository on GitHub, at the commit this page was made from: the board is BLINK_LED/blink_led_circuit/LED Circuit II/PRY 1/PRY3/PRY3.kicad_pcb and its schematic BLINK_LED/blink_led_circuit/LED Circuit II/LED Circuit II.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PRY3 design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).