
Open src
AntoJijoKICKU/Smart_PLUG
This is Untested version of Hardware Double check your guts before take this as reference

Board and code for a drip-photography timer
Drip timer is an open-source printed circuit board by adamstaff, from the adamstaff/drip_photography repository on GitHub. It is a 2-layer board of 79.2 × 49 mm with 17 parts on 29 nets, routed with 94 tracks and 0 vias.
It is built around the MOC3021S. Its parts include 4 connectors, 3 switches, 2 resistors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Board and code for a drip-photography timer
Based on https://petapixel.com/2016/06/04/build-diy-double-water-drip-system-high-speed-photos/
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10k | Potentiometer_THT:Potentiometer_Bourns_PTV09A-1_Single_Vertical | DripTime1, FlashTime1 |
| 2 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
| 1 | BATT | Connector_Wire:SolderWire-1sqmm_1x02_P5.4mm_D1.4mm_OD2.7mm_Relief | J1 |
| 1 | DIPxx-1Axx-11x | Relay_THT:Relay_StandexMeder_DIP_LowProfile | K1 |
| 1 | Drips | Button_Switch_THT:SW_E-Switch_EG1271_SPDT | SW2 |
| 1 | FLASH | Connector_Wire:SolderWire-1sqmm_1x02_P5.4mm_D1.4mm_OD2.7mm_Relief | J3 |
| 1 | Flash Trigger | Connector_Audio:Jack_3.5mm_CUI_SJ1-3523N_Horizontal | J4 |
| 1 | GO | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | MOC3021S | Package_DIP:SMDIP-6_W7.62mm | U3 |
| 1 | ProMicro | Arduino_ProMicro:ProMicro | U1 |
| 1 | VALVE | Connector_Wire:SolderWire-1sqmm_1x02_P5.4mm_D1.4mm_OD2.7mm_Relief | J2 |
The 13 most common of 17 parts.

AntoJijoKICKU/Smart_PLUG
This is Untested version of Hardware Double check your guts before take this as reference




hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

DDeGonge/OS-ARM
This arm is not industrial and it will not be fast, but that is not my goal. But it will hopefully be a very nice looking arm fully capable of 6dof motion, cheap enough to keep it accessable but capable enough to…
It measures 79.2 × 49 mm and has 2 copper layers, 1.6 mm thick.
17 parts, built around the MOC3021S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the adamstaff/drip_photography repository on GitHub, at the commit this page was made from: the board is drip-timer/drip-timer.kicad_pcb and its schematic drip-timer/drip-timer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask adamstaff before reusing the design.