Skip to the content
2 layers47 × 40.3 mmEbyte pcb e22, the printed circuit board in 3D

ESP32s3 Variant board with E22-900M30S for Meshtatic

Size
47 × 40.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
6
Nets
13
Pads
46
Tracks, vias
79, 0
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
29 Sep 2025
Updated
30 Sep 2025

Overview

Ebyte pcb e22 is an open-source printed circuit board by adamko-space, from the adamko-space/Meshtastic-esp32s3-ebyte-e22900m30s repository on GitHub, published under the MIT licence. It is a 2-layer board of 47 × 40.3 mm with 6 parts on 13 nets, routed with 79 tracks and 0 vias.

Its parts include 4 connectors, 1 capacitor and 1 IC.

README

README.md

ESP32s3 - devkit c1 n16r8 clone with CDEBYTE E22-900M30S - Variant for Meshtastic

I'm presenting my meshtastic node variant using a Chinese clone of the Esp32s3n61r8 devkit c1 board with 16MB flash, 8MB PSRAM, and the E22-900M30S module. After analyzing the free ESP pins, the connection is correct. The connection is described in the variant.h file.

E22900M30S requires

bash
#define TX_GAIN_LORA 7 // gain module e22
#define SX126X_MAX_POWER 22 // max power + gain = max radio power - EU 27db

this is what the configure.h documentation says

bash
// Gain for common modules with transmit PAs
#ifdef EBYTE_E22_900M30S
// 10dB PA gain and 30dB rated output; based on measurements from
// https://github.com/S5NC/EBYTE_ESP32-S3/blob/main/E22-900M30S%20power%20output%20testing.txt
#define TX_GAIN_LORA 7
#define SX126X_MAX_POWER 22
#endif

1. File info

  • esp32-s3-devkit-e22/variant.h - define connection and setup configure
  • esp32-s3-devkit-e22/platformio.ini - platformio config file
  • esp32-s3-devkit-e22/pins_arduino.h - required config file for arduino/esp platforms
  • boards/esp32-s3-devkit-e22.json - board devkit c1 clone configuration
  • partion.csv - partition file for 16MB flash - put in header folder

2. Install and assembly

  • Add files from this repository, keeping their proper locations to Meshtastic firmware
  • compile the selected env and upload to your board
  • connect the radio module as defined in the variant.h file
  • Make sure everything is in order so as not to damage the radio.
  • run node and test your network :)

3. Power

Standard consumption is approximately 110mA, with an average of 350-450mW at 27dBm during transmission.

  • ADD a 100nF capacitor between the +5V power supply for the radio module and GND, and a 2000uF electrolytic capacitor to maintain power.

4. Troubleshooting

I'm on the 2.7.9-10 alpha software package.

-https ssl cert error during connect from client.meshtatistc.org

Apart from these issues, everything seems to be working fine.

5. Links

Parts

6
QtyValueFootprintReferences
23pin Header 2.54Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1, J3
28pin Header 2.54Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ2, J4
1100nfCapacitor_SMD:C_0805_2012MetricC1
1e22900m30se22:PE22(400M30S)U1

Similar boards

  • 2 layers18.5 × 11.1 mmSwitch, the printed circuit board in 3D

    Switch

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    6 parts4.3kMIT
  • 2 layers14.6 × 33 mmBrain board SD Card 1, the printed circuit board in 3D

    Brain board SD Card 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    6 parts1.2k
  • 2 layers9 × 9 mmDpoint, the printed circuit board in 3D

    Dpoint

    Jcparkyn/dpoint

    Open-source digital stylus using camera tracking and inertial measurements

    6 parts1.1kMIT
  • 2 layers51.5 × 16.6 mmMicroswitchXY Endstop, the printed circuit board in 3D

    MicroswitchXY Endstop

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    6 parts1.1kGPL-3.0
  • 2 layers21.9 × 76.7 mmAmiga External, the printed circuit board in 3D

    Amiga External

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    6 parts1kGPL-3.0
  • 2 layers88.9 × 50.8 mmBusinesscard, the printed circuit board in 3D

    Businesscard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    6 parts915
  • 2 layers20.3 × 15.2 mmL0 RGB led, the printed circuit board in 3D

    L0 RGB led

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    6 parts546MIT
  • 2 layers9 × 3.6 mmOpticalEncoder, the printed circuit board in 3D

    OpticalEncoder

    adamb314/ServoProject

    Getting the most out of your hobby servo

    6 parts545

Questions

How big is the Ebyte pcb e22 PCB?

It measures 47 × 40.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ebyte pcb e22 use?

6 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ebyte pcb e22 KiCad files?

From the adamko-space/Meshtastic-esp32s3-ebyte-e22900m30s repository on GitHub, at the commit this page was made from: the board is PCB/ebyte-pcb-e22.kicad_pcb and its schematic PCB/ebyte-pcb-e22.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ebyte pcb e22 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).