Skip to the content
2 layers44.7 × 85.1 mmJonoBro, the printed circuit board in 3D

Ace's Electronics Pty Ltd 12V heater controller for mirrors and windscreens

Size
44.7 × 85.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
65
Nets
51
Pads
314
Tracks, vias
341, 418
Pours
16
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
6 Sep 2023
Updated
11 Jul 2025

Overview

JonoBro is an open-source printed circuit board by Aces-Electronics, from the Aces-Electronics/ae-landy-heater-controller repository on GitHub, published under the MIT licence. It is a 2-layer board of 44.7 × 85.1 mm with 65 parts on 51 nets, routed with 341 tracks and 418 vias.

It is built around the ESP32-C3-MINI-1, AOZ1280CI and CSD19537Q3, with the 1N5819WS, MMBT3904 and PMEG6020ER among its other parts. Its parts include 16 resistors, 11 capacitors, 10 transistors, 6 diodes and 5 connectors. It belongs with the ESP32 and RISC-V boards of this library.

Main components

6

README

README.md

Ace's Electronics

Ace's Electronics Pty Ltd
12V heater controller for mirrors and windscreens

Looking to get up and running?

Project Goals:

The overall goal of this project is to make a simple, robust and reliable heater controller for vehicles that have heated mirrors and windscreens, like a Land Rover Defender for example. The controller will be solid state and be able to handle up to 30A at 12-14V with a maximum input voltage of 20V.

Design goals:

  • Smallest form-factor possible while being able to handle 30A without getting too hot
  • Simple configuration
  • Easy to mount
  • Zero maintenance

JonoTron-3000 v0.3

Version 0.3 was made to address a small issue with the switch pull-up, which was incorrectly tied to 12V instead of 3.3V. The hardware pull-up has been removed completely in ths version as the ESP32 has internal pull-ups that are more than capable.

v0.3 Front AE-Land-Heater_Controller AE-Land-Heater_Controller-Exploded

JonoTron-3000 v0.2

Version 0.2 was made to addresss a couple of isssues, namely:

  • Input and ouputs polarity was swapped, thanks to the xt-60 injection mould anomally that made a - look like a + when I eyeballed it to see which side was negative
  • All outputs were tied together and were't individually controllable
  • The board couldn't really handle 30A, not safely

Boards are tested and workng well!

v0.2 renders:

v0.2 Front

Where to Buy:

Available to purchase in Australia or New Zealand via The AE Store

Support:

Contact me direct via ace<@>aceselectronics.com.au, just make it look like a normal email address. (hiding from the bots ;)

Parts

65
QtyValueFootprintReferences
913kResistor_SMD:R_0603_1608MetricR1, R5, R7, R9, R10, R11, R12, R16, R18
7100nFCapacitor_SMD:C_0603_1608MetricC3, C4, C7, C8, C9, C10, C11
7CSD19537Q3Package_SON:VSON-8_3.3x3.3mm_P0.65mm_NexFETQ1, Q3, Q5, Q6, Q8, Q9, Q10
6TestPointTestPoint:TestPoint_Pad_D1.0mmTP1, TP2, TP4, TP5, TP6, TP8
41N5819WSDiode_SMD:D_SOD-323D4, D5, D6, D7
31kResistor_SMD:R_0603_1608MetricR8, R15, R17
3Conn_01x02_PinAcea:AMASS_XT60PW-F_1x02_P7.20mm_HorizontalJ1, J2, J3
3MMBT3904Package_TO_SOT_SMD:SOT-23Q2, Q4, Q7
210uFCapacitor_SMD:C_0603_1608MetricC2, C6
25.1kResistor_SMD:R_0603_1608MetricR13, R14
2MountingHoleMountingHole:MountingHole_2.5mmH1, H2
2MountingHoleMountingHole:MountingHole_4.3mm_M4_Pad_ViaH3, H4
2SW_PushAcea:ALPSALPINE-SKSCLBE010_C115361SW1, SW2
110uHInductor_SMD:L_Chilisin_BMRA00040415L1
12.2kResistor_SMD:R_0603_1608MetricR4
1220uFCapacitor_SMD:CP_Elec_6.3x7.7C1
122uFCapacitor_SMD:CP_Elec_6.3x5.4C5
14.3kResistor_SMD:R_0603_1608MetricR2
1AOZ1280CIPackage_TO_SOT_SMD:SOT-23-6U1
1Conn_01x02_PinAcea:AMASS_XT60PW-M_1x02_P7.20mm_HorizontalJ4
1ESP32-C3-MINI-1Espressif:ESP32-C3-MINI-1U2
1LOGOAcea:ae_5mmG***
1PMEG6020ERDiode_SMD:Nexperia_CFP3_SOD-123WD1
1TestPointTestPoint:TestPoint_Loop_D3.80mm_Drill2.5mmTP3
1USB_C_Receptacle_USB2.0Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J6
1WS2812-2020LED_SMD:LED_WS2812B-2020_PLCC4_2.0x2.0mmD2

Similar boards

  • 2 layers28.6 × 30 mmEsp daikin r1p1, the printed circuit board in 3D

    Esp daikin r1p1

    gregdavill/daikin-esp

    ESP32-C3 hardware to connect to a Daikin ducted A/C system. enabling WiFi control in Home Assistant.

    37 parts29
  • 6 layers90 × 153 mmBlackpants, the printed circuit board in 3D

    Blackpants

    o7-machinehum/Blackpants

    Open blackpants.kicadpro for the active A523 schematic and PCB. It replaces the A33 hierarchy and uses AXP717C + AXP323 with 2GB LPDDR4.

    300 parts189MIT
  • 4 layers106 × 63.5 mmBrineomatic, the printed circuit board in 3D

    Brineomatic

    hoeken/brineomatic

    Open Source Watermaker Controller.

    323 parts47LGPL-2.1
  • 4 layers154.5 × 112.9 mmLibrePLC32, the printed circuit board in 3D

    LibrePLC32

    AndreiVladescu/LibrePLC32

    The goal of the project is to create a compact, hackable, and well-documented PLC platform for industrial automation experiments, prototyping, education, and open hardware development.

    295 parts14CERN-OHL-P-2.0
  • 2 layers40 × 50 mmEFUSE2024, the printed circuit board in 3D

    EFUSE2024

    brianz123/EFUSE

    32 parts
  • 2 layers43.1 × 32.4 mmBuck, the printed circuit board in 3D

    Buck

    d0n13/boatv4

    2024 version of electric boat

    38 partsMIT
  • 4 layers90 × 100 mmPCB Cuarto, the printed circuit board in 3D

    PCB Cuarto

    Jose-WaitNRest/PCB-Cuarto

    79 parts
  • 4 layers90 × 100 mmPCB Madre, the printed circuit board in 3D

    PCB Madre

    Jose-WaitNRest/PCB-Madre

    64 parts

Questions

How big is the JonoBro PCB?

It measures 44.7 × 85.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the JonoBro use?

65 parts, built around the ESP32-C3-MINI-1, AOZ1280CI, CSD19537Q3 and 1N5819WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the JonoBro KiCad files?

From the Aces-Electronics/ae-landy-heater-controller repository on GitHub, at the commit this page was made from: the board is hardware/v0_2/JonoBro.kicad_pcb and its schematic hardware/v0_2/JonoBro.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the JonoBro design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).