
LogicAnalyzer
gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

A shield for the D1 Mini bus (ESP8266, ESP32 and others) that connects dust, humidity and other sensors
D1 air quality is an open-source printed circuit board by accelerando-consulting, from the accelerando-consulting/aio-d1_air_quality repository on GitHub. It is a 2-layer board of 27.4 × 42.7 mm with 10 parts on 14 nets, routed with 113 tracks and 14 vias.
Its parts include 5 connectors, 1 capacitor, 1 resistor and 1 IC. It belongs with the sensors and measurement boards of this library.
This shield is designed to take one of two kinds of dust sensor

The shield also has I2C headers (note, using the Lolin VCDG pinout not the nowadays quasi standard QWIIC GVDC pinout!) which allow attaching a variety of temperature, humidity and other sensors (eg you might like volatile organic compounds, or CO2).
The semi-ubitquitous DHT12 or AM2302 temp/humidity sensors are cheap and cheerful. buy
The BMP180 temperature/pressure sensor likewise. buy
In the COVID era CO2 is of interest, you may like the MH-Z19 sensor for this. The Sensirion sensor is the gold standard but runs about $100.
If you're using Arduino, just search for the names of your sensors in the library manager.
If you want a leg up, check out our Stacx framework which provides a ready-to-use MQTT sensor runtime for ESP8266 and ESP32 (It's Arduino-based, too).

| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | 150R | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 220uF | Capacitor_SMD:CP_Elec_6.3x7.7 | C1 |
| 1 | Conn_01x07_Male | Connector_JST:JST_XH_B7B-XH-AM_1x07_P2.50mm_Vertical | J5 |
| 1 | GP2Y10 | Connector_JST:JST_ZE_BM06B-ZESS-TBT_1x06-1MP_P1.50mm_Vertical | J1 |
| 1 | I2C1 | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J2 |
| 1 | I2C2 | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J3 |
| 1 | I2C3 | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J4 |
| 1 | RX | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm | JP2 |
| 1 | TX | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm | JP1 |
| 1 | WeMos_mini | D1:wemos-d1-mini-with-pin-header | U1 |

gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch


OLIMEX/OLINUXINO
OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
It measures 27.4 × 42.7 mm and has 2 copper layers, 1.6 mm thick.
10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the accelerando-consulting/aio-d1_air_quality repository on GitHub, at the commit this page was made from: the board is d1_air_quality.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask accelerando-consulting before reusing the design.