Skip to the content
2 layers27.3 × 35.6 mmCatsquirter, the printed circuit board in 3D

A D1 mini shield for operating a low voltage pump or other motor

Size
27.3 × 35.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
15
Nets
21
Pads
53
Tracks, vias
75, 22
Pours
3
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
3 Dec 2022
Updated
4 Dec 2022

Overview

Catsquirter is an open-source printed circuit board by accelerando-consulting, from the accelerando-consulting/aio-catsquirter repository on GitHub. It is a 2-layer board of 27.3 × 35.6 mm with 15 parts on 21 nets, routed with 75 tracks and 22 vias.

Its parts include 3 resistors, 3 connectors, 2 diodes, 1 IC and 1 transistor.

README

README.md

CatSquirter - a mosfet switching shield for pumps or other small loads

This project is a circuit board that allows one to control a high current output using a Mostfet rather than a relay. It is intended to stack atop the Lolin D1 mini microcontroller board, or any other board that uses the D1 bus (such as Accelerando Redsoil (nRF52840) , Accelerano Bungan (nRF52833) or Accelerando Cowan (ESP32-C3).

It was originally created to drive a small submersible fountain pump in order to produce a brief spray of water (harmless but surprising) to discourage a pet from scratching an item of furniture.

How it works

Jumpers allow any of D0,D1,D5-D8 to be connected to the gate of the MOSFET. When the corresponding pin is HIGH, the MOSFET turns on and power flows to the PUMP socket.

Another jumper controls the source of the power to the pump. For a battery operated pump, fit a Lolin battery shield and connect the battery to the catsquirter shield, then connect the second battery connector to the Lolin shield. This arrangement uses the high current available direct from a lithium battery to run the pump.

Alternatively, if your project is not battery powered, a jumper allows connecting the 5v or 3v3 pins from the D1 stacking bus to the mosfet drain. (Be careful not to use more current than your regulator can handle!). In one instance I'm using the 5v from the USB connecter to run a small vacuum pump.

Finally, if you have a higher voltage load (say, 12v), you could connect power to one of the battery headers (in which case DO NOT connect the second header to a battery shield!).

A LED will light when the pump fet is enabled.

What can I do with it

  • Water your indoor pot-plants.
  • Control a low voltage cooling or ventilation fan
  • Make a small drinking fountain for people or pets.
  • Run a vacuum pump or fume extractor for soldering.
  • Stack several of these (with different jumper settings on each one) to control several devices.
  • Control low voltage LED lighting (up to 2A, for higher current lighting see Accelerando Jahlo).
  • Control a heavy duty relay for more signifiant loads

Parts

15
QtyValueFootprintReferences
2LOGOLOGOG***, G***
110kResistor_SMD:R_0805_2012MetricR1
11kResistor_SMD:R_0805_2012MetricR2
1220RResistor_SMD:R_0805_2012MetricR3
1BattConnectors_JST:JST_XH_S02B-XH-A_02x2.50mm_AngledJ2
1Batt OutConnectors_JST:JST_XH_S02B-XH-A_02x2.50mm_AngledJ3
1D1Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1
1LED_SmallLED_SMD:LED_0805_2012MetricD1
1LL014NPackage_TO_SOT_SMD:SOT-223Q1
1M4Diode_SMD:D_SMBD2
1PUMPAccelerando:SolderJumper-5_P1.3mm_Open_Pad1.0x1.5mmJP2
1PumpConnectors_JST:JST_XH_S02B-XH-A_02x2.50mm_AngledJ1
1WeMos_miniwemos:wemos-d1-mini-connectors-onlyU1
1vPUMPJumper:SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mmJP3

Similar boards

  • 2 layers19 × 76 mmSub, the printed circuit board in 3D

    Sub

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    15 parts3kApache-2.0
  • 2 layers26.7 × 62.2 mmDeniseadapter, the printed circuit board in 3D

    Deniseadapter

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    15 parts1kGPL-3.0
  • 2 layers100 × 44 mmVideoslot, the printed circuit board in 3D

    Videoslot

    mntmn/amiga2000-gfxcard

    MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

    15 parts1k
  • 2 layers91 × 51 mmBusinessCard, the printed circuit board in 3D

    BusinessCard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    15 parts915
  • 2 layers24.3 × 57.9 mmFlosspods pro flex, the printed circuit board in 3D

    Flosspods pro flex

    kenp-io/not-for-airpods-repairs

    The content of this repository is licensed under the WTFPL License. Please have a close look at the terms before using this material.

    15 parts609WTFPL
  • 2 layers20.3 × 15.2 mmL0 Load, the printed circuit board in 3D

    L0 Load

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    15 parts546MIT
  • 2 layers68 × 50 mmEleLab v2 PowerFeed, the printed circuit board in 3D

    EleLab v2 PowerFeed

    Chrismettal/EleLab_v2

    Cheap DIY lab system for hobbyists and the tinkering folk

    15 parts531GPL-3.0
  • 2 layers50.8 × 35.6 mmInterface, the printed circuit board in 3D

    Interface

    harbaum/I2C-Tiny-USB

    Cheap and simple I²C to USB interface

    15 parts454

Questions

How big is the Catsquirter PCB?

It measures 27.3 × 35.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Catsquirter use?

15 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Catsquirter KiCad files?

From the accelerando-consulting/aio-catsquirter repository on GitHub, at the commit this page was made from: the board is catsquirter.kicad_pcb and its schematic catsquirter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Catsquirter design in my own project?

Its repository states no licence, so its author keeps all rights: ask accelerando-consulting before reusing the design.