2 layers38.2 × 39.6 mm
Fallhaub quicc nousbc
acamilo/Maxxon-DC-Motor-Controller-QWIIC
Board to control 1 maxon motor over i2c. With USB-PD
28 parts1
2 layers25 × 56 mm
Fallhaub quicc
acamilo/Maxxon-DC-Motor-Controller-QWIIC1Board to control 1 maxon motor over i2c. With USB-PD
- Size
- 25 × 56 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 29
- Nets
- 54
- Pads
- 164
- Tracks, vias
- 619, 90
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 30 Apr 2020
- Updated
- 7 May 2020
Overview
Fallhaub quicc is an open-source printed circuit board by acamilo, from the acamilo/Maxxon-DC-Motor-Controller-QWIIC repository on GitHub. It is a 2-layer board of 25 × 56 mm with 29 parts on 54 nets, routed with 619 tracks and 90 vias.
It is built around the ATSAMD21E18A-MU, DRV8838DSG and PTN5110DHQ, with the AP2112K-3.3 among its other parts. Its parts include 9 connectors, 6 capacitors, 4 ICs, 2 resistors and 2 diodes. It belongs with the power boards and the SAM D and SAM boards of this library.
Main components
4
ATSAMD21E18A-MU
QFN-32-EP(5x5)-40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 26 32 Bit 32KB 48MHz ARM Cortex-M0+ Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、Built-in general-purpose timer、Hardware CRC、Programmable watchdog、Calendar function、Touch function QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
DRV8838DSG
WSON-8-EP(2x2)-40℃~+85℃ 1.8A 1.8A 1.8V~7V 280mΩ 5nA Current sensing/regulation function、Active braking function Yes WSON-8-EP(2x2) Brushed DC Motor Drivers ROHSTexas InstrumentsMotor Driver ICsPTN5110DHQ
--40℃~+85℃ 2.7V~5.5V 300Kbps I2C、USB - Interface - Specialized ROHSNXP SemiconductorsInterface - Specialized
AP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorised
README
README.mdOSH Park-compatible 2 Layer KiCad Template
This is a KiCad template to simplify making printed circuit boards.
It comes with all the design rules to meet the 2-layer OSH Park specs and stackup.
Instructions
- Open KiCad.
- Open Preferences > Configure Paths and note the value of 'KICAD_PTEMPLATES'.
- Download the template zip and extract into the location of 'KICAD_PTEMPLATES'.
- In KiCad, open File > New Project > New Project from Template.
- Select the location of your new project. The name of the folder will be the name of your project.
- The templates with folders in the 'KICAD_PTEMPLATES' are listed under 'Portable Templates" tab.
- Select the template and click 'OK'.
- Your project now exists, so you can open EESchema and PCBNew and design as usual.
Maxxon-DC-Motor-Controller-QWIIC
Parts
29| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 1u | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5, C6 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 2 | 1.5k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | Conn_01x02_Female | Connector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_Vertical | J3, J6 |
| 2 | Conn_01x04_Female | Connector_JST:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | J4, J7 |
| 2 | Conn_01x04_Female | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J5, J9 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | APA102 | LED_SMD:LED_RGB_PLCC-6 | D1 |
| 1 | ATSAMD21E18A-MU | fallhaub-quicc:QFN50P500X500X100-33N | U1 |
| 1 | Conn_01x02_Female | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J8 |
| 1 | Conn_02x03_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_Vertical | J2 |
| 1 | DRV8838 | Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm | U3 |
| 1 | Fuse | fallhaub-quicc:NANO-0154-OMNI-BLOK-Fuse-Holder | F2 |
| 1 | LED | Capacitor_SMD:C_0603_1608Metric | D2 |
| 1 | PTN5110 | fallhaub-quicc:HX2QFN16 | U2 |
| 1 | SW_SPST | Button_Switch_SMD:SW_SPST_CK_KXT3 | SW1 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_Amphenol_12401610E4-2A | J1 |
More from acamilo/Maxxon-DC-Motor-Controller-QWIIC
1Similar boards
- 2 layers37 × 76.5 mm
Temp ref
acamilo/Cheap-Feaver-Screener-PID-Control-PCB
PCB to control two heating elements with i2c or dallas temp sensors.
51 parts1 - 2 layers25 × 25 mm
CircuitBrains Basic v1 2
neubauek/CircuitBrains
Small form-factor 48-pin castellated pad module. Designed to allow an easy implementation of CircuitPython in maker/hacker projects without the bulk of a large breakout board.
23 parts50MIT - 2 layers41.3 × 35 mm
- 2 layers51.8 × 53.6 mm
CatWAN Farmer
ElectronicCats/CatWAN_Farmer
CatWAN Farmer, a grower's water saving open source project with LoRa
53 parts7 - 2 layers48 × 26 mm
- 2 layers52 × 80 mm
- 2 layers90 × 118 mm
Roverbase
stephendade/roverbase
A PCB design for Power and Motor control for small robots
61 parts3GPL-3.0 - 4 layers111.8 × 69.8 mm
Questions
How big is the Fallhaub quicc PCB?
It measures 25 × 56 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Fallhaub quicc use?
29 parts, built around the ATSAMD21E18A-MU, DRV8838DSG, PTN5110DHQ and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Fallhaub quicc KiCad files?
From the acamilo/Maxxon-DC-Motor-Controller-QWIIC repository on GitHub, at the commit this page was made from: the board is fallhaub-quicc.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Fallhaub quicc design in my own project?
Its repository states no licence, so its author keeps all rights: ask acamilo before reusing the design.