Skip to the content
2 layers120 × 85 mmDriverPad, the printed circuit board in 3D

A custom PCB-based button controller project for FRC 5719. The controller uses a Seeed Studio XIAO ESP32-C3, eight Cherry MX-style mechanical switches, and a small OLED display.

Size
120 × 85 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
22
Pads
87
Tracks, vias
151, 8
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
10 Oct 2026
Updated
12 Oct 2026

Overview

DriverPad is an open-source printed circuit board by AamirKPathan, from the AamirKPathan/Titan-Driver-Pad repository on GitHub. It is a 2-layer board of 120 × 85 mm with 19 parts on 22 nets, routed with 151 tracks and 8 vias.

Its parts include 8 diodes, 8 switches and 2 ICs.

README

README.md

FRC 5719 Titan Driver Pad

Final Product

A custom PCB-based button controller project for FRC 5719. The controller uses a Seeed Studio XIAO ESP32-C3, eight Cherry MX-style mechanical switches, and a small OLED display.

Enclosure: Bottom case only. There is no top case or cover.

Project Images

Final productPCB render
Final productFull PCB render
Design and development views

Schematic

Finished schematic

PCB outline

Final PCB outline

Firmware project

PlatformIO project structure

Electrical rules check

ERC report

Project Status

  • Firmware builds successfully with PlatformIO.
  • OLED and graphics libraries installed.
  • Assemble and test physical hardware.
  • Verify all eight switches and OLED.
  • Develop the PC-side virtual gamepad bridge.
  • Test compatibility with the intended FRC Driver Station setup.

Hardware

ComponentDetails
MicrocontrollerSeeed Studio XIAO ESP32-C3
Switches8 Cherry MX-style mechanical switches
Display0.91-inch SSD1306 OLED, 128 × 32, I2C
PCB design softwareKiCad
Firmware environmentVS Code + PlatformIO
EnclosureBottom case only; no top case

Controls

SwitchIntended Input
SW1Left stick up (W / 1)
SW2Left stick left (A / 2)
SW3Left stick down (S / 3)
SW4Left stick right (D / 4)
SW5L2
SW6R2
SW7R1
SW8L1

Controls are intended to remain active while a switch is held and deactivate when released. Opposite directions cancel each other out.

Pin Assignments

Switch Matrix

SignalXIAO Pin LabelGPIO
Row 1D0 / A02
Row 2D1 / A13
Row 3D2 / A24
Row 4D3 / A35
Column 1D6 / TX8
Column 2D7 / RX9

Matrix Layout

Column 1 (GPIO 8)Column 2 (GPIO 9)
Row 1 (GPIO 2)SW1SW5
Row 2 (GPIO 3)SW2SW6
Row 3 (GPIO 4)SW3SW7
Row 4 (GPIO 5)SW4SW8

Note: The physical matrix wiring and diode orientation have not yet been verified. Confirm them against the final KiCad schematic and PCB when the hardware arrives.

OLED Display

OLED SignalXIAO Pin LabelGPIO
SDAD4 / A4 / SDA6
SCLD5 / A5 / SCL7

The firmware currently uses I2C address 0x3C. Some OLED modules use 0x3D.

Firmware

The firmware is developed using VS Code and PlatformIO with the Arduino framework for ESP32-C3.

Build Firmware

Open a terminal in the Firmware directory and run:

bash
pio run

Upload Firmware

Once the hardware arrives, connect the XIAO ESP32-C3 through USB and run:

bash
pio run --target upload

Open Serial Monitor

bash
pio device monitor

The firmware is intended to output controller states in the following format:

text
STATE,UP,LEFT,DOWN,RIGHT,L1,L2,R1,R2

Each state is represented by 0 (inactive) or 1 (active).

Software Dependencies

  • VS Code
  • PlatformIO
  • Arduino framework for ESP32-C3
  • Adafruit GFX Library
  • Adafruit SSD1306 Library

Current Limitations

  • Firmware compilation has succeeded, but the firmware has not yet been tested on physical hardware.
  • Switch scanning, debounce behavior, diode orientation, and matrix wiring still require verification.
  • OLED operation must be confirmed on the assembled PCB.
  • The PC-side virtual gamepad bridge is still to be developed and tested.
  • Compatibility with the intended FRC Driver Station setup has not yet been confirmed.

Hardware Testing Checklist

Once the hardware arrives:

  • Inspect the PCB and verify component orientation.
  • Check power, ground, and possible shorts before connecting USB.
  • Upload the firmware.
  • Confirm that the OLED initializes.
  • Test each switch individually.
  • Verify that every switch activates the correct control.
  • Confirm opposite directions cancel each other.
  • Confirm controls deactivate when switches are released.
  • Test the PC-side virtual gamepad bridge.
  • Verify the intended FRC Driver Station workflow.

Project Structure

The project may be organized as follows:

text
Titan Driver Pad/
├── Firmware/
│   ├── platformio.ini
│   └── src/
│       └── main.cpp
├── Hardware/
│   └── KiCad project files
└── README.md

Adjust the folder names in this section to match the actual project structure.

Credits

Developed for FRC Team 5719 — Pink Titans.

Parts

19
QtyValueFootprintReferences
81N914Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D2, D3, D4, D5, D6, D7, D8
8SW_PushButton_Switch_Keyboard:SW_Cherry_MX_1.00u_PCBSW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8
1ER_OLEDM0.91_1x-I2CDisplay:ER_OLEDM0.91_1x-I2CU2
1LOGOPCB:logoG***
1MOUDLE-SEEEDUINO-XIAORF_Module:MCU_Seeed_ESP32C3U1

Similar boards

  • 2 layers43.9 × 27.7 mmTcd1304-4v, the printed circuit board in 3D

    Tcd1304-4v

    OpnTec/open-spectrometer-hardware

    Open source VIS spectrometer

    19 parts1.5k
  • 2 layers50 × 60 mmDebate Device, the printed circuit board in 3D

    Debate Device

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    19 parts915
  • 2 layers102.9 × 96.7 mmISA adapter, the printed circuit board in 3D

    ISA adapter

    polpo/picogus

    Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support

    19 parts805
  • 2 layers60 × 39 mmPs2usb, the printed circuit board in 3D

    Ps2usb

    rasteri/HIDman

    Adapting USB devices to work on old computers

    19 parts432
  • 2 layers70.1 × 43.2 mmIaq device, the printed circuit board in 3D

    Iaq device

    nkitanov/iaq_board

    IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

    19 parts396
  • 2 layers80 × 80 mmGB BRK CPU G1, the printed circuit board in 3D

    GB BRK CPU G1

    Gekkio/gb-hardware

    Game Boy -related custom hardware by gekkio

    19 parts379CC-BY-4.0
  • 2 layers25.4 × 25.4 mmIna169, the printed circuit board in 3D

    Ina169

    Ardumower/ardumower

    Develop an open source robotic lawn mower (HW+SW reference platform)

    19 parts282
  • 2 layers58.4 × 28.6 mmNew rele, the printed circuit board in 3D

    New rele

    zmaker/arduino_cookbook

    gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

    19 parts269

Questions

How big is the DriverPad PCB?

It measures 120 × 85 mm and has 2 copper layers, 1.6 mm thick.

What parts does the DriverPad use?

19 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the DriverPad KiCad files?

From the AamirKPathan/Titan-Driver-Pad repository on GitHub, at the commit this page was made from: the board is Driver/Production/PCB/DriverPad.kicad_pcb and its schematic Driver/Production/PCB/DriverPad.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the DriverPad design in my own project?

Its repository states no licence, so its author keeps all rights: ask AamirKPathan before reusing the design.