Skip to the content
2 layers28.8 × 10.5 mmWifiFlex connector, the printed circuit board in 3D

WifiFlex connector

Y2K-x/WiFiflex-JLC5

Fork of supertazon's Wii WiFi Relocation Flex PCB for JLCPCB

Size
28.8 × 10.5 mm
Copper layers
2
Thickness
0.13 mm
Parts
2
Nets
16
Pads
28
Tracks, vias
106, 25
Pours
3
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
1 Feb 2024
Updated
1 Feb 2024

Overview

WifiFlex connector is an open-source printed circuit board by Y2K-x, from the Y2K-x/WiFiflex-JLC repository on GitHub. It is a 2-layer board of 28.8 × 10.5 mm with 2 parts on 16 nets, routed with 106 tracks and 25 vias.

It belongs with the radio and wireless boards of this library.

README

README.md

WiFiflex

Wii WiFi relocation flex pcb

Wififlex front image IMG_3469

Note: This version is specifically tailored for production through JLCPCB, as the original design did not fit within their capabilities. If you are planning on having these manufactured through a service such as PCBWay or GoldPhoenix's pool, please consider using the original version instead!

A flex pcb to easily relocate the Wii WiFi chip for Wii portables (useless for stock Wii) by using the WiFi chip connector. The WiFi chip is notorious for being difficult to relocate by handwiring it due to wire length sensitivity. License is permissive, you are free to make, sell and distribute the flex pcb.

The flex pcb is compatible with a OMGWTF trim, it also does not overlap with the NAND relocation flex.

This version requires that you relocate RA20 from the Wii motherboard directly onto the flex, instead of the flex soldering directly to RA20. This was done since JLCPCB's castellation tolerances are not tight enough to support soldering to the 0402 resistor pack.

Repo contains the KiCad source files (needs KiCad 8.0RC2 minimum to work) and gerbers.

BOM

Molex connector 52991-0208: DigiKey or Mouser

How to order

As suggested by YveltalGriffin, the original design requires fabrication through a service that has tight tollerances with castellations, such as PCBWay. This modification allows fabrication through cheaper services such as JLCPCB.

This modification is untested and highly experimental. Things may not line up or it might not work at all. Try this at your own risk (and report your findings on the BitBuilt forums please!)

Through JLC, please make sure to select these settings:

  • FPC thickness: 0.11 mm
  • Surface finish: Immersion gold (ENIG) (1U")
  • Finished copper: 1/3 oz Cu (18μm) (Ideally you'd want 0.5oz copper here but JLC does not seem to support this yet)

How to install

  1. Populate the flex pcb, take note of the silkscreen to correctly position the connector. I highly recommend using solder paste and a hot plate or hot air, it's definitely easier than hand soldering it. Check continuity between the connector pins and the vias before moving on. - Also be sure to remove RA20 off the Wii motherboard and install it onto the designated spot on the flex. No need to worry about polarity here. - After removing RA20, remove any residual solder left on the RA20 footprint pads on the Wii motherboard with solder wick. This is to ensure the flex sits properly on the board and isn't damages by leftover solder.

  2. Scratch the two pairs of vias 3.3V and GND while making sure to scratch the space between both.

  3. Position the flex to locate where you will scratch the Wii's GND plane for the upper right via on the flex.

  4. Scratch the Wii's GND plane at the correct position. image Vias and GND spot scratched, could have done better but wanted to avoid scratching the surrounding traces

  5. Add flux and pre-tin the vias and GND spot. I noticed the 3.3V vias needed more heat to be properly tinned.

  6. Position the flex and secure it with a piece of kapton tape between the GND vias and the connector.

  7. Solder the GND vias with the Wii GND vias and the 3.3V vias with the Wii's 3.3V vias. Don't forget you might need to apply more heat on the 3.3V vias.

  8. Add flux and solder to the pads on the flex that align up directly with the left over pads on the RA20 footprint.

  9. Check continuity between the these points and the vias they connect to on the Wii motherboard (follow the traces).

  10. If everything is nominal then proceed with soldering the big GND via, otherwise reflow as needed.

Now that you are done you can try putting a WiFi chip on there and see if you get signal. Be careful to not short anything on the board, you might need to add kapton tape either on the chip or on the Wii motherboard.

Please handle the flex pcb with care! It is quite fragile, I inadvertently ripped it off the Wii while testing. Make sure you really solder that big GND via for better stability.

Contributors

  • supertazon: Initial design and routing
  • YveltalGriffin: Via stitching, large GND via addition, silkscreen and general tips on routing
  • Y2K: Modified design for JLCPCB specifications, with permission from supertazon.

Acknowledgements

Parts

2
QtyValueFootprintReferences
1Conn_01x20_PinConnector_Molex:Molex_SlimStack_52991-0208_2x10_P0.50mm_VerticalJ1
1R_Pack04Resistor_SMD:R_Array_Convex_4x0402RA20

Similar boards

  • 2 layers37 × 19 mmPassive rpi hub75-adapter, the printed circuit board in 3D

    Passive rpi hub75-adapter

    hzeller/rpi-rgb-led-matrix

    Controlling up to three chains of 64x64, 32x32, 16x32 or similar RGB LED displays using Raspberry Pi GPIO

    2 parts4.4kGPL-2.0
  • 2 layersDiode template, the printed circuit board in 3D

    Diode template

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    2 parts547GPL-3.0
  • 2 layers20.3 × 15.2 mmL0 button, the printed circuit board in 3D

    L0 button

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    2 parts546MIT
  • 2 layers35.1 × 46.8 mmSDEX2M2 Breakout Board, the printed circuit board in 3D

    SDEX2M2 Breakout Board

    NVNTLabs/switch2-SDEX2M2

    Micro SD Express to M.2 NVME Adapter for Nintendo Switch 2

    2 parts542GPL-3.0
  • 2 layers59.3 × 36.6 mmExpansionBoardTemplate, the printed circuit board in 3D

    ExpansionBoardTemplate

    BlueSCSI/BlueSCSI-v2

    BlueSCSI v2/Ultra - an open source, open hardware, SCSI emulator using the Pi Pico PR2040 and Pico 2 RP2350

    2 parts459GPL-3.0
  • 2 layersAlpha.9mm.wire, the printed circuit board in 3D

    Alpha.9mm.wire

    ohmtech-rdi/eurorack-blocks

    Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

    2 parts410
  • 2 layers26.7 × 64 mmGpu power, the printed circuit board in 3D

    Gpu power

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    2 parts397Apache-2.0

Questions

How big is the WifiFlex connector PCB?

It measures 28.8 × 10.5 mm and has 2 copper layers, 0.13 mm thick.

What parts does the WifiFlex connector use?

2 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the WifiFlex connector KiCad files?

From the Y2K-x/WiFiflex-JLC repository on GitHub, at the commit this page was made from: the board is KiCad/WifiFlex-connector.kicad_pcb and its schematic KiCad/WifiFlex-connector.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the WifiFlex connector design in my own project?

Its repository states no licence, so its author keeps all rights: ask Y2K-x before reusing the design.