

Vacuum Former
- Size
- 100 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 47
- Nets
- 51
- Pads
- 183
- Tracks, vias
- 233, 37
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 5 Jan 2025
- Updated
- 3 Nov 2025
Overview
Vacuum Former is an open-source printed circuit board by XCR1793, from the XCR1793/Vacuum-Former repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 100 × 50 mm with 47 parts on 51 nets, routed with 233 tracks and 37 vias.
It is built around the ESP32-S3-WROOM-1-N8, LTV-816S and SRV05-4, with the 1N5819HW-7-F-01 and PT01-D115D-B103 among its other parts. Its parts include 14 resistors, 10 capacitors, 6 ICs, 3 connectors and 2 diodes. It belongs with the ESP32 boards of this library.
Main components
5ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesLTV-816S
SMD-4P-50℃~+110℃ 1 1.2V 100mV@20mA,1mA 3us 4us 50% 50mA 5kV 600% 6V 80V DC Phototransistor SMD-4P Transistor, Photovoltaic Output Optoisolators ROHSLite-OnTransistor, Photovoltaic Output OptoisolatorsSRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)1N5819HW-7-F-01
SOD-123Schottky DiodesDiodes IncorporatedPT01-D115D-B103
插件Potentiometers & Variable ResistorsCUI
README
README.mdVacuum Former
An affordable vacuum former capable of forming medium to large bucks and molds. The system must also be safe for anyone to use in both hardware and electronics (as this requires mains).

Features
- Hybrid Frame - Rigid aluminium combined with cheap cement fiber boards results in a fireproof frame.
- RCBO - Short, fault and overcurrent protection.
- SSR - PWM based temperature control.
Hardware
The frame is designed to be collapsible so it is easily stored. The heater box, material frame and base plattern uses the same 440mm x 640mm aluminium 2020 frames which makes it easy to fabricate and assemble. All components that get close to the heatsource is fireproof and areas that are not subject to heat are 3D printed to both save cost and time to construct.
Embedded
Although dangerous, many safety features were implemented to reduce the risk of injury. This includes breakers and rcbos to detect shorts, faults and if the user accidentally touches the live wires. All electronics are rated to and beyond what is required to run the system of 240VAC at 20A, this does mean however, that the user must have a port which can supply 15A and beyond if you want to run the heater box. The average house hold outlet should provide 10A at 240VAC, however if your in the Americas you'll use 110VAC. This means in both senarios, you will have to find a high current compatible port or else you will trip a breaker. If you dont have one, then you must remove 2 of the heating elements as each of them uses 1KW. This will however reduce the total amount of heat you can provided and may not be able to rais the temperature enough to heat difficult to form materials such as polycarbonate which requires around 240C to form properly.
Roadmap
- Milestones: Hardware Assembly Complete
- Milestones: Electrical Wiring
- Milestones: Electrical Box
- Milestones: Controller Box
- Work In Progress: V5.1
- Work In Progress: Extended version for V5.1 (Vacuum charge upgrade)
To Do List
- V5.1: Proper heating element power control
- V5.1: Heating area extended to the entire material frame
- V5.1: More even heating spread
- V5.1: Temperature control
- V5.1: Proper platen sealing
- V5.1: Fully sealed plumbing
- V5.1: Figure out a slightly faster clamping mechanism
- V5.1: Figure out a way to more reliably measure sag/prestretching
- Extended: Floor standing
- Extended: Vacuum tank
- Extended: Vacuum pump
- Extended: Upgraded plumbing
Parts
47| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | BootSW1, SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8, SW9 |
| 5 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7, R8, R12, R14 |
| 4 | 1uF | Resistor_SMD:R_0603_1608Metric | C2, C3, C4, C5 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C6, C7 |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric | R11, R13 |
| 2 | 1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R10 |
| 2 | Conn_01x04_Socket | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | OLED_5V-G1, OLED_G-5V1 |
| 2 | SMD-PHOTOCOUPLER-5KV-LTV-816S_4P-4.6X6.5MM_ | Optocoupler_LTV-816S:SMD4-2.54-4.6X6.5MM | U4, U5 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | 11K | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 12K | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 1N4007 | Diode_1N4007:DIOAD1060W80L520D270 | D2 |
| 1 | 1N5819HW-7-F | Schottky_Diode_1N5819HW-7-F:SOD3715X145N | D1 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 22uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C9 |
| 1 | 63K | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 640 | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 691137710002 | Terminal_Block_691137710002:691137710002 | J1 |
| 1 | AP7366-33W5-7 | AP7366-SOT25:AP7366 | U3 |
| 1 | AP7366-W5-7 | AP7366-SOT25:AP7366 | U2 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | ESP32-S3-WROOM-1 | PCM_Espressif:ESP32-S3-WROOM-1U | U6 |
| 1 | PT01-D115D-B103 | PT01-D115D-B103:TRIM_PT01-D115D-B103 | R2 |
| 1 | SRV05-4 | PCM_marbastlib-various:SOT-23-6-routable | U1 |
Similar boards
- 2 layers78 × 622 mm

- 2 layers87 × 66 mm

- 2 layers130.6 × 138.2 mm

- 4 layers165.1 × 63.5 mm

- 4 layers100 × 100 mm

- 2 layers79.5 × 79.5 mm

Esp32-energymeter V2
ElektorLabs/esp32-energymeter
The Elektor ESP32 Energy Meter project, featuring schematics, PCB designs, and ESPHome integration for advanced energy monitoring
116 parts48MIT - 4 layers115 × 55 mm

Roamr motors
uw-roamr/roamr
turn your phone into a robot running SLAM with two motors, two control boards, and a bluetooth chip
110 parts6 - 2 layers82.6 × 74.3 mm

Questions
How big is the Vacuum Former PCB?
It measures 100 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Vacuum Former use?
47 parts, built around the ESP32-S3-WROOM-1-N8, LTV-816S, SRV05-4 and 1N5819HW-7-F-01. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Vacuum Former KiCad files?
From the XCR1793/Vacuum-Former repository on GitHub, at the commit this page was made from: the board is Older Versions/V5/Embedded/Vacuum Former V5 Circuit/Vacuum Former.kicad_pcb and its schematic Older Versions/V5/Embedded/Vacuum Former V5 Circuit/Vacuum Former.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Vacuum Former design in my own project?
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).