Skip to the content
2 layers35 × 33.5 mmNODE WATERING, the printed circuit board in 3D

A smart watering sytem built whit a master circuit and a node for every waterable plant.

Size
35 × 33.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
6
Nets
17
Pads
28
Tracks, vias
31, 0
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
4 Oct 2026
Updated
28 Oct 2026

Overview

NODE WATERING is an open-source printed circuit board by Vlebi, from the Vlebi/smart-watering repository on GitHub, published under the MIT licence. It is a 2-layer board of 35 × 33.5 mm with 6 parts on 17 nets, routed with 31 tracks and 0 vias.

Its parts include 2 connectors, 1 resistor, 1 IC, 1 diode and 1 transistor. It belongs with the ESP32 and RISC-V boards of this library.

README

README.md

DripLogic

A node based smart watering system using MAC addres based wireless communication between a main module and separate node modules with theoritically no limit for how many nodes it can use.

System Architecture

DripLogic uses two or more hardware units that communicate without a router, using ESP-NOW.

Master Unit

  • ESP32-C3 SuperMini
    • I2C header J1
    • LED D1 on GPIO3 with a 220 Ω resistor
    • button SW1 on GPIO2 to GND image

Watering Node

  • ESP32-C3 SuperMini
    • Capacitive soil moisture sensor J1 on GPIO0
    • 5V/12V solenoid valve J2
    • N-channel MOSFET Q1
    • 10 kΩ pull-down resistor R1
    • 1N4007 flyback diode D1 for inductive spike protection image

BOM and Costs

Total price for Master + a node is 28 usd + shipping,

PartDescriptionQTYUnit Price (USD)Total Price (USD)Vendor
ESP32-C3-SUPERMINIMain controllers for both main and node PCBs23.286.56HESTORE
SOILCAP-V20Capacitive soil moisture sensor12.152.15HESTORE
AO3400AN-channel MOSFET for valve control12.552.55HESTORE
WSV-12V1/2 inch NC 12V DC solenoid valve17.887.88HESTORE
1N4007Flyback diode for inductive spike suppression11.261.26HESTORE
10K 5%Pull-down resistor for MOSFET gate11.001.00HESTORE
MP1584EN-LF12V to 5V step-down buck converter module13.873.87HESTORE
AC142R-02P-5.085.08mm terminal blocks for power and valve20.661.32HESTORE
ZL201-08G (WWS8G)2.54mm 1x8 female headers for ESP32-C3 socketing40.251.00HESTORE
Tax & ShippingTax and shipping for the whole order13.853.85HESTORE
TOTAL1531.44

ESP32-C3 SuperMini 2 piece Capacitive Soil Sensor 1 piece Solenoid Valve 1 piece MOSFET 1 piece Resistor, Diode, led, button 1 piece

Hardware Design

  • Designed the pcb layouts in kicad
  • Fully checked with DRC and ERC

Software

  • Language: MicroPython
  • Wireless: ESP-NOW
  • Tools used: Flashed with esptool.py and managed using the VS Code MicroPico extension
  • Python code boot.py (initializes esp-NOW) and main.py (reads moisture, sends data, receives data, sends commands, receives commands.

Project Journal

Created as part of a Hack Club project documenting the journey:

journalling is in JOURNAL.md

Getting Started

  1. Clone the repo

    git clone https://github.com/Vlebi/smart-watering.git

    Flash MicroPython to your ESP32-C3 SuperMini boards using esptool.py.

  2. Transfer boot.py and main.py to the Master and Node units using MicroPico.

  3. Follow the KiCad schematics to solder your boards, mount the sensors, and connect the solenoid valves.

Parts

6
QtyValueFootprintReferences
110000Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
1Conn_01x02_PinConnector_PinHeader_1.00mm:PinHeader_1x02_P1.00mm_Vertical_SMD_Pin1LeftJ2
1Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1
1DDiode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD1
1ESP32-C3-SuperMinikicadplugnis:ESP32-C3-SuperMiniU1
1Q_NMOS_GDSPackage_TO_SOT_THT:TO-220-3_VerticalQ1

More from Vlebi/smart-watering

1
  • 2 layers35.5 × 37 mmMAIN WATERING, the printed circuit board in 3D

    MAIN WATERING

    Vlebi/smart-watering

    A smart watering sytem built whit a master circuit and a node for every waterable plant.

    5 parts1MIT

Similar boards

  • 2 layers18.5 × 11.1 mmSwitch, the printed circuit board in 3D

    Switch

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    6 parts4.3kMIT
  • 2 layers14.6 × 33 mmBrain board SD Card 1, the printed circuit board in 3D

    Brain board SD Card 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    6 parts1.2k
  • 2 layers9 × 9 mmDpoint, the printed circuit board in 3D

    Dpoint

    Jcparkyn/dpoint

    Open-source digital stylus using camera tracking and inertial measurements

    6 parts1.1kMIT
  • 2 layers51.5 × 16.6 mmMicroswitchXY Endstop, the printed circuit board in 3D

    MicroswitchXY Endstop

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    6 parts1.1kGPL-3.0
  • 2 layers21.9 × 76.7 mmAmiga External, the printed circuit board in 3D

    Amiga External

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    6 parts1kGPL-3.0
  • 2 layers88.9 × 50.8 mmBusinesscard, the printed circuit board in 3D

    Businesscard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    6 parts915
  • 2 layers20.3 × 15.2 mmL0 RGB led, the printed circuit board in 3D

    L0 RGB led

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    6 parts546MIT
  • 2 layers9 × 3.6 mmOpticalEncoder, the printed circuit board in 3D

    OpticalEncoder

    adamb314/ServoProject

    Getting the most out of your hobby servo

    6 parts545

Questions

How big is the NODE WATERING PCB?

It measures 35 × 33.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the NODE WATERING use?

6 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the NODE WATERING KiCad files?

From the Vlebi/smart-watering repository on GitHub, at the commit this page was made from: the board is .NODE_PCB/NODE_WATERING/NODE_WATERING.kicad_pcb and its schematic .MAIN_PCB/MAIN_WATERING/MAIN_WATERING.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the NODE WATERING design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).