Skip to the content
4 layers157.5 × 132 mmCREWLINE PRIM PCB-001, the printed circuit board in 3D

CREWLINE PRIM PCB-001

VSangtani/crewline-roller-pcb

This folder holds the live KiCad 10 project. The revision label on the board is still V3.1-H1. The previous revision and its reports are in ../history/.

Size
157.5 × 132 mm
Copper layers
4
Thickness
1.67 mm
Parts
101
Nets
78
Pads
288
Tracks, vias
611, 44
Pours
3
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
28 Sep 2026
Updated
1 Oct 2026

Overview

CREWLINE PRIM PCB-001 is an open-source printed circuit board by VSangtani, from the VSangtani/crewline-roller-pcb repository on GitHub. It is a 4-layer board of 157.5 × 132 mm with 101 parts on 78 nets, routed with 611 tracks and 44 vias.

It is built around the 1N4148WS, 204-10SDRD/S530-A3-L and XT60PW-M, with the DMN3404L, IRF4905STRL(UMW) and SLA-12VDC-SL-A among its other parts. Its parts include 10 connectors, 1 capacitor and 1 transistor.

Main components

7

README

new/README.md

Crewline primary board, brake and E-stop revision

This folder holds the live KiCad 10 project. The revision label on the board is still V3.1-H1. The previous revision and its reports are in ../history/.

What changed since the previous revision

  • J7 grows from 4 to 7 positions and carries the brake lines.
  • J10 is new, 7 positions, and carries the E-stop lines.
  • J8 is removed. Its arming loop now sits on J3 pins 2 to 5, beside MODE_SEL on pin 1.
  • J6 is now the seat sensor connector, 3 positions with one spare.
  • J2 and all test points are removed.
  • J3, J5, J6, J7 and J10 are Molex Micro-Fit 3.0 single-row vertical through-hole headers. J1 (XT60) and J4 (Phoenix MKDS screw terminal block) are unchanged.
  • Four relays are new: K_BRAKE_CAT1, K_BRAKE_CAT2, ESTOP_COM_RELAY1 and ESTOP_COM_RELAY2. The existing brake relay is now K_BRAKE_SEAT_BOMAG1.
  • All relay logic for brake and E-stop sits on the child sheet brake-estop.kicad_sch.
  • D1, the flyback diode across the POWER1 coil, is turned round so its cathode is on ARMED_HOT. The original drawing had it forward-biased across the coil.
  • R_ARMED_PD1 is removed. The POWER1 coil already ties ARMED_HOT to ground.
  • The six red LEDs use the standard LED symbol, pin 1 cathode, so they match the footprint mark and the assembler's library convention.
  • The six DNP flags on C1, J1, J9 and the three DPDT relays are cleared. All are fitted.
  • Every part number was checked against the JLCPCB parts library. See the BOM section.
  • The custom symbols and footprints live in lib/ and are registered in the project library tables.
  • The board is 136 by 132 mm. It grew 56.5 mm to the right for the Phoenix headers, then shrank 21.5 mm after the Molex swap.

Files

  • CREWLINE-PRIM-PCB-001.kicad_pro, .kicad_sch, .kicad_pcb are the project, root sheet and board.
  • brake-estop.kicad_sch is the child sheet with the relay logic.
  • schematic.pdf is the two-page schematic export.
  • pcb-top.png and pcb-bottom.png are the native renders.
  • pcb.step is the native solid model.
  • bom.csv is the bill of materials, grouped by value, footprint and part number.
  • netlist.xml is the schematic netlist.
  • erc.json and drc.json are the rule check reports.
  • lib/ holds the project symbol and footprint libraries. V31_H1.pretty holds the Phoenix headers of the previous revision, kept for reference.
  • models/ holds the 3D models.
  • tools/ holds the grid router and its helpers. See tools/README.md.
  • manufacturing/ holds the Gerber set, the drill files and the JLCPCB assembly files. See manufacturing/README.md.

Connectors

RefFunctionPartMating housingFitted by
J1BatteryAmass XT60PW-MXT60 plugJLCPCB
J3Mode select and arming loop, 5 wayMolex 43650-051543645-0500JLCPCB
J4Power outputs, 10 way screw terminalPhoenix MKDS 1,5/10-5,08, 1715802none, screwCustomer
J5CAN cables, 10 wayMolex 43650-101543645-1000JLCPCB
J6Seat sensor, 3 wayMolex 43650-031543645-0300JLCPCB
J7Brake, 7 wayMolex 43650-071543645-0700JLCPCB
J9Converter shield, 2 by 6 pin header2.54 mm headershieldJLCPCB
J10E-stop, 7 wayMolex 43650-071543645-0700JLCPCB

J7 and J10 take the same plug. Label both ends of each harness. Harness contacts are the Molex 43030 series, in the 18 to 20 AWG and 20 to 24 AWG versions, crimped with the Molex tool.

Pin tables

PinJ3J6J7J10
1MODE_SELECU_SEATBRAKE_JETESTOP_JOY_NG
2+12V_GATEDSEATBRAKE_JOYESTOP_JOY
3loop, joined to 4spareBRAKE_ECUESTOP_ECU
4loop, joined to 3BRAKE_JOY_NFESTOP_REMOTE
5ARMED_HOTBRAKE_JOY_NGESTOP_ECU_NF
6BRAKE_ECU_NFESTOP_ECU_NF
7BRAKE_ECU_NGESTOP_ECU_NG

J10 pins 5 and 6 are the same net because ESTOP_JOY_NF is wired directly to ESTOP_ECU_NF.

PinJ5J4
1ECU_CANLSTARLINK_PWR_P
2JET2_CANLGND
3JET2_CANHJET_DIO_PWR_P
4ECU_CANHGND
5JOY_CANHLED_PWR_P
6JET1_CANHGND
7JET1_CANHJETSON_PWR_P
8JET1_CANLGND
9JET1_CANLSTEER_PWR_P
10JOY_CANLGND

J5 pins 6 and 7, and 8 and 9, are doubled so two cables can land on the JET1 bus without a splice.

Relay coils

Every coil returns through MODE_SEL_DRV, which Q_MODE1 pulls low when MODE_SEL is high.

RelayCoil supplySeries diode
K_BRAKE_SEAT_BOMAG1+12V_KITnone
K_BRAKE_CAT1+12V_KITnone
K_BRAKE_CAT2BRAKE_JETD_BRAKEJET_SER1
ESTOP_COM_RELAY1+12V_KITnone
ESTOP_COM_RELAY2ESTOP_REMOTED_ESTOPREMOTE_SER1

BRAKE_JET and ESTOP_REMOTE come from the Syslogic carrier outputs, which are isolated high-side switches at 12 V maximum. The series diode blocks any reverse path into them. With MODE_SEL_DRV floating near 12 V in manual mode, the two coils fed from those outputs see no useful voltage and stay released. If a later carrier ever drives these lines from 24 V, or from a supply that is live while the kit is disarmed, return those two coils through a relay contact instead of MODE_SEL_DRV. Each coil draws about 17 mA and each indicator LED about 5 mA.

Brake behaviour

ModeBRAKE_JETBRAKE_ECUBRAKE_ECU_NGBRAKE_ECU_NF
manualanyBRAKE_JOYBRAKE_JOY_NGBRAKE_JOY_NF
autonomy12 V, releasedBRAKE_JETGNDopen
autonomy0 V, applied, or Jetson deadBRAKE_JETopenGND

E-stop behaviour

ESTOP_ECU_NF is wired directly to ESTOP_JOY_NF.

ModeESTOP_REMOTEESTOP_ECUESTOP_ECU_NGESTOP_ECU_NF
manualanyESTOP_JOYESTOP_JOY_NGESTOP_JOY_NF
autonomy12 VESTOP_JOYESTOP_JOY_NGESTOP_JOY_NF
autonomy0 V, or Jetson deadGNDopenESTOP_JOY_NF and ESTOP_JOY_NG, tied together

In the E-stop stop state the NF line takes whatever the joystick NG line carries. It is not grounded from the board. Confirm that the Bomag input accepts this before the first vehicle test.

Board layout

  • J5, J7 and J10 sit on the bottom edge between the mounting holes. J3 and J6 sit on the left edge.
  • The seven DPDT relays sit in one row at Y 143.22 mm. Each has its flyback diode 3 mm above the coil pads and its LED and resistor above that.
  • The inner layers are the ground plane (In1.Cu) and the +12V_KIT plane (In2.Cu). The front layer carries a ground fill in the gaps. Every pad on those nets joins its fill with thermal spokes.
  • Track and via sizes follow the net classes: 2.5 mm tracks with 1.0/0.5 mm vias for +12V_GATED, 1.0 mm tracks with 0.8/0.4 mm vias for +12V_KIT and the power outputs, 0.4 to 0.6 mm tracks with 0.6/0.3 mm vias for signals.
  • No track runs inside a mounting hole washer area or closer than 1.8 mm to the board edge.
  • The mounting holes are H1 to H4 on a 120 by 115 mm rectangle: (60, 58), (180, 58), (60, 173) and (180, 173) in board coordinates. They are board-only footprints with no schematic symbol.
  • The connector swap and the final relay routing were done by hand in the editor. The first routing pass used tools/router.py.

BOM

bom.csv carries a manufacturer part number, an LCSC number and, where JLCPCB does not fit the part, an Assembly field reading "Customer fitted". Every LCSC number was opened on the JLCPCB parts page and checked for package, value, rating, stock and assembly type. Parts fitted by the customer after assembly:

  • J4, Phoenix 1715802, screw terminal block.
  • F_MAIN1, F_STEER1, F_JET1, F_CONV1, F_DIO1 and F_LED1, Keystone 3568 blade fuse holders. The fuses themselves are not on the BOM: 30 A main, 15 A steering, 10 A Jetson, 10 A converter, 5 A DIO and 3 A LED.

Verification

  • ERC reports one warning. ESTOP_ECU_NF and ESTOP_JOY_NF name the same net by design.
  • DRC reports zero errors, zero warnings and zero unconnected items.
  • Every pad net on the board was compared with the schematic netlist. All 245 match.
  • The netlist was compared before and after every scripted schematic edit. Only the intended nets changed each time.
  • An independent review of the schematic, the board and the BOM was run after the first routing.
  • These checks are switched off in the project settings and were confirmed clean when switched on: ERC single_global_label, four_way_junction and footprint_filter; DRC missing_courtyard and footprint_type_mismatch. The track_not_centered_on_via check is switched on.

Open items before manufacture

  • Run Update PCB from Schematic once more so the footprint fields take the audited part numbers. Until then the parity check lists 52 field differences.
  • Decide whether the six fuse holders stay customer fitted or move to a JLCPCB-stocked holder. A replacement must match the Keystone 3568 footprint: two 1.78 mm holes per terminal, 3.4 mm apart, with the terminals 9.92 mm apart.
  • Bump the revision label before the order and add a revision text on the silkscreen. The schematic title blocks are empty.
  • Confirm the harness contact and crimp tool part numbers from the Molex site before ordering.
  • KiCad's 3D model library has no model for the Micro-Fit 43650 headers, so pcb.step and the renders show the five headers as bare pads. Molex offers STEP files for them on the part pages; drop one into models/ and point the footprint at it if the enclosure fit needs them.

Open questions for the original board designer

  • JOY_TERM_R1 and STEER_TERM_R1 are both 120 ohm across JET1_CANH and JET1_CANL, which puts 60 ohm on that bus from this board alone. Both are fitted on the boards in service. A CAN bus normally has one 120 ohm terminator at each end and none in the middle. Was this intended, for example because the board sits at the end of two separate cable runs?
  • D1 on the boards in service: the original drawing had it forward-biased across the POWER1 coil, so the fitted part is either reversed relative to the drawing or has failed open.

Tools

The first routing pass was made with tools/router.py under the KiCad Python interpreter. Run the rule check after every change. The router is not a substitute for it.

Parts

101
QtyValueFootprintReferences
132.2kResistor_SMD:R_0805_2012MetricBRK-Relay-RES1, BRKCAT1-Relay-RES1, BRKCAT2-Relay-RES1, CONV_RES1, DIO_RES1, ECU-Relay-RES1, ESTOPCOM1-Relay-RES1, ESTOPCOM2-Relay-RES1, JET_RES1, Joy-Relay-RES1, LED_RES1, STR_RES1, STR-Relay-RES1
121N4148WS1N4148WS:SOD-323_L1.8-W1.3-LS2.5-RDD_BRAKEJET_SER1, D_ESTOPCOM1, D_ESTOPCOM2, D_ESTOPREMOTE_SER1, D_KBRAKE1, D_KBRAKECAT1, D_KBRAKECAT2, D_KECUCAN1, D_KJOYCAN1, D_KSTEER1, D1, D2
11TestPointTestPoint_Black:TEST-TH_BD2.54-P1.4_BLACKARM_TP1, BATT_GND_TP1, BRK_ECU_NF_TP1, BRK_ECU_NG_TP1, BRK_ECU_TP1, CAN1H_TP1, CAN1L_TP1, ESTP_ECU_NF_TP1, ESTP_ECU_NG_TP1, ESTP_ECU_TP1, MODE_TP1
9TestPointTestPoint_Red:TEST-TH_BD2.54-P1.4_RED12V_GATE_TP1, BATT_TP1, CONV_TP1, DIO_TP1, JET_TP3, KIT_TP1, LED_TP1, STAR_TP1, STR_TP1
8GreenLED_SMD:LED_0805_2012MetricBRK-Relay-LED1, BRKCAT1-Relay-LED1, BRKCAT2-Relay-LED1, ECU-Relay-LED4, ESTOPCOM1-Relay-LED1, ESTOPCOM2-Relay-LED1, Joy-Relay-LED1, STR-Relay-LED1
7Relay_DPDTRelay_THT:Relay_DPDT_Omron_G6AESTOP_COM_RELAY1, ESTOP_COM_RELAY2, K_BRAKE_BOMAG1, K_BRAKE_CAT1, K_BRAKE_CAT2, K_ECUCAN1, K_JOYCAN1
6REDLED_SMD:LED_0805_2012MetricCONV_LED1, DIO_LED1, JET_LED1, LED_LED1, PWR_LIGHT1, STR_LED1
4MountingHole_4.3mm_M4MountingHole:MountingHole_4.3mm_M4H1, H2, H3, H4
210Fuse:Fuseholder_Blade_Mini_Keystone_3568F_CONV1, F_JET1
2100nCapacitor_SMD:C_0805_2012MetricC_STEER2, C2
210kResistor_SMD:R_0805_2012MetricR_MODE_PD1, R1
2120Resistor_SMD:R_0805_2012MetricJOY_TERM_R1, STEER_TERM_R1
1100Resistor_SMD:R_0805_2012MetricR_MODE_GATE1
11000uFCap_1000uF:ECA1EM102C1
115Fuse:Fuseholder_Blade_Mini_Keystone_3568F_STEER1
13Fuse:Fuseholder_Blade_Mini_Keystone_3568F_LED1
130Fuse:Fuseholder_Blade_Mini_Keystone_3568F_MAIN1
1470uFCapacitor_THT:C_Radial_D8.0mm_H11.5mm_P3.50mmC_STEER1
15Fuse:Fuseholder_Blade_Mini_Keystone_3568F_DIO1
15.6kResistor_SMD:R_0805_2012MetricR_ARMED1
1BATTERYXT60PW-M:CONN-TH_XT60PW-MJ1
1BRAKE INPUTSV31_H1:MCV_1.5_7_5.08_Pad2.6J7
1CAN CABLESV31_H1:MCV_1.5_10_5.08_Pad2.6J5
1CHARGE SHIELD HEADERConnector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_VerticalJ2
1Conn_02x06_Counter_ClockwiseConnector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_VerticalJ9
1DIOV31_H1:MCV_1.5_5_5.08_Pad2.6J3
1DMN3404LPackage_TO_SOT_SMD:SOT-23Q_MODE1
1ESTOP INPUTSV31_H1:MCV_1.5_7_5.08_Pad2.6J10
1IRF4905STRLIRF4905:TO-252-2_L6.6-W6.1-P4.57-LS10.1-BR-CWQ1
1K_GATESongle_SLA:RELAY-TH_SLA-XXVDC-XL-APOWER1
1PWR INPUTSTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-10-5.08_1x10_P5.08mm_HorizontalJ4
1SAFETY_CONNECTORV31_H1:MCV_1.5_5_5.08_Pad2.6J8
1SEAT_CONNECTORWAGO_2604:WAGO_2604-1102J6
1SLA-12VDC-SL-ASongle_SLA:RELAY-TH_SLA-XXVDC-XL-AK_STEER1
1SMBJ24CADiode_SMD:D_SMBTVS1

More from VSangtani/crewline-roller-pcb

3
  • 4 layers136 × 132 mmCREWLINE PRIM PCB-001, the printed circuit board in 3D

    CREWLINE PRIM PCB-001

    VSangtani/crewline-roller-pcb

    This folder holds the live KiCad 10 project. The revision label on the board is still V3.1-H1. The previous revision and its reports are in ../history/.

    79 parts
  • 4 layers101 × 132 mmCREWLINE PRIM PCB-001, the printed circuit board in 3D

    CREWLINE PRIM PCB-001

    VSangtani/crewline-roller-pcb

    This folder holds the live KiCad 10 project. The revision label on the board is still V3.1-H1. The previous revision and its reports are in ../history/.

    78 parts
  • 4 layers157.5 × 132 mmCREWLINE PRIM PCB-001, the printed circuit board in 3D

    CREWLINE PRIM PCB-001

    VSangtani/crewline-roller-pcb

    This folder holds the live KiCad 10 project. The revision label on the board is still V3.1-H1. The previous revision and its reports are in ../history/.

    78 parts

Similar boards

  • 4 layers70 × 60 mmCAN Logger V2.0, the printed circuit board in 3D

    CAN Logger V2.0

    deep-th/CAN_Logger

    This is a compact and reliable CAN logger board built for automotive and industrial applications. It features the ESP32-S3 microcontroller and MCP25625 CAN controller with integrated transceiver, supporting two…

    138 parts3
  • 4 layers246.8 × 154.7 mmAc psu, the printed circuit board in 3D

    Ac psu

    johonkanen/ac_psu_kicad

    test full kicad conversion of latest ac_psu hardware files done by claude. originally drawn in proteus

    377 partsMIT
  • 4 layers50.8 × 22.9 mmBench stim wing, the printed circuit board in 3D

    Bench stim wing

    ThatguyCplus/throttleECU

    STM32F411CE Throttle ECU — PID position control with AS5048A encoder, H-bridge motor, safety module

    114 parts1
  • 4 layers110 × 90 mmUsb hub 3s, the printed circuit board in 3D

    Usb hub 3s

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    116 parts3MIT
  • 4 layersIONPAK2, the printed circuit board in 3D

    IONPAK2

    m-labs/ionpak

    A modern, low-cost universal controller for hot-cathode ionization vacuum gauges. (WIP)

    259 parts23
  • 4 layers135.8 × 149.3 mmTapBadgeV2, the printed circuit board in 3D

    TapBadgeV2

    Xasin/TapBadgeV2

    The second, far more ambitious version of the TapBadge wearable

    110 parts6GPL-3.0
  • 2 layers96.8 × 56.4 mmOOK48 PICO, the printed circuit board in 3D

    OOK48 PICO

    g4eml/RP2040_OOK48_LCD

    Experimental Synchronous On Off Keying Encoder and Decoder with LCD Touch Display

    26 parts3GPL-3.0
  • 4 layers50 × 100 mmStDevboard, the printed circuit board in 3D

    StDevboard

    teletype7/IRIS

    166 parts3MIT

Questions

How big is the CREWLINE PRIM PCB-001 PCB?

It measures 157.5 × 132 mm and has 4 copper layers, 1.67 mm thick.

What parts does the CREWLINE PRIM PCB-001 use?

101 parts, built around the 1N4148WS, 204-10SDRD/S530-A3-L, XT60PW-M and DMN3404L. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CREWLINE PRIM PCB-001 KiCad files?

From the VSangtani/crewline-roller-pcb repository on GitHub, at the commit this page was made from: the board is new/_restore_backup_2026-09-30T12-59-34-863/CREWLINE-PRIM-PCB-001.kicad_pcb and its schematic history/original-design/CREWLINE-PRIM-PCB-001.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CREWLINE PRIM PCB-001 design in my own project?

Its repository states no licence, so its author keeps all rights: ask VSangtani before reusing the design.