

HeaterControl
Multi node heater control on Nordic BTLE
- Size
- 32.8 × 24.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 17
- Nets
- 58
- Pads
- 132
- Tracks, vias
- 283, 35
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 24 Mar 2019
- Updated
- 31 Jan 2020
Overview
HeaterControl is an open-source printed circuit board by TheTosters, from the TheTosters/HeaterControl repository on GitHub, published under the BSD-3-Clause licence. It is a 2-layer board of 32.8 × 24.9 mm with 17 parts on 58 nets, routed with 283 tracks and 35 vias.
It is built around the DS18B20 and BL654. Its parts include 6 resistors, 4 connectors, 2 capacitors, 2 ICs and 1 diode.
Main components
2README
README.mdIMPORTANT
Toolchain:
- gcc-arm-none-eabi-8-2018-q4-major, or
- gcc-arm-none-eabi-8-2019-q3-update-linux
NRF SDK:
- nRF5_SDK_15.2.0_9412b96
You also need nrfprog tools and small patch for SDK from CMSIS. But this is handled by preapre_env.sh
To build & run tests...
This is super-glue solution, so your eyes will bleeed... It will use host compiler (not cross-compiler) to build host based tests. It is NOT ment to test all, only most complicated logic. So to have test build and run you have to:
cmake .. -DBUILD_TESTS=ON
make allthen you can call for example:
./test/time_schedule_tests
Manual patching SDK
If you set C++ to use C++17 dialect then compilation fails :P You have to manualy patch NordicSDK (15.2) and upgrade CMSIS to have things working go here Arm CMSIS 5 on Github and download following files which should be placed here:
| CMSIS file | Destination | |
|---|---|---|
| libarm_cortexM4lf_math.a, libarm_cortexM4l_math.a | > | nordic_SDK_15.2/components/toolchain/cmsis/dsp/GCC |
| arm_cortexM4lf_math.lib arm_cortexM4l_math.lib | > | nordic_SDK_15.2/components/toolchain/cmsis/dsp/ARM |
| CMSIS_5-develop/CMSIS/Core/Include | > | nordic_SDK_15.2/components/toolchain/cmsis/include |
clean & build all should work
Variants
This repository contains several firmware variants. It can be used by setting proper defines for CMake, most easy way to do it is to execute ccmake. Below is list of build variants and their descriptions:
| Variant | Entry point | Description |
|---|---|---|
| Indoor SHT_ADV | main_indoor_1.cpp | BT: Advertisement Sensor: SHT30 Buttons: None LED: None Display: None |
| Indoor SHT_GATT | main_indoor_1a.cpp | BT: GATT Sensor: SHT30 Buttons: None LED: None Display: None |
| Indoor DS_FULL | main_indoor_1.cpp | BT: Advertisement Sensor: DS18B20 Buttons: yes LED: None Display: Yes |
Origins
first instruction taken from: https://github.com/Polidea/cmake-nRF5x It is constantly changed and improved (or downproved :P)
Parts
17| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 4,7k | Resistor_SMD:R_0402_1005Metric | R1, R2, R4 |
| 2 | 10 | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-2012-12_Kemet-R | C2 |
| 1 | 22 | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | BL654 | Laird:BL654 | U2 |
| 1 | BTN | Resistor_SMD:R_1206_3216Metric | SW1 |
| 1 | Battery | CR2032_BatHolder:Cr2032-Holder | B1 |
| 1 | DEV_PORT | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | DS18B20 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical_SMD_Pin1Left | J1 |
| 1 | Ext | Connector_PinHeader_1.00mm:PinHeader_2x04_P1.00mm_Vertical_SMD | J4 |
| 1 | OSTB0603C1C-A | LED_RGB:LED_PACKAGE_1.6x1.5mm | D1 |
| 1 | SHT30-DIS-B | SHT30-DIS-B:DFN250X250X100-9N | U3 |
| 1 | TC2030-CTX | Tag-Connect:TC2030-NL_SMALL | P1 |
More from TheTosters/HeaterControl
4- 2 layers53.3 × 39.1 mm

- 2 layers48.5 × 36.8 mm

- 2 layers35.3 × 30.2 mm

- 2 layers31.5 × 27.2 mm

Similar boards
- 2 layers54 × 54 mm

- 2 layers33.7 × 97.8 mm

HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470 - 2 layers121 × 68 mm

Freeds sanchez
pablozg/freeds
Derivador de energía solar excedente creado por Pablo Zerón, Diseño PCB por Amcalo, Tester original por Aeizoon, Wiki por Zoilo Mora
42 parts108 - 2 layers80 × 54.9 mm

ESP32WifiAisTempVolt2
AK-Homberger/NMEA2000WifiGateway-with-ESP32
This repository shows how to build a NMEA2000 WiFi Gateway with voltage and temperature alarms.
18 parts94GPL-3.0 - 2 layers52 × 61 mm

Arduino motorfocus
fehlfarbe/arduino-motorfocus
Arduino motorfocus with moonlite protocol for telescopes
23 parts58MIT - 2 layers69 × 57 mm

- 2 layers26 × 34.8 mm

- 2 layers162 × 60 mm

Esp shield
felixwittwer/homeassistant_automaic_greenhouse
A cool Project to make your greenhouse smart. What about automaic irrigation and collecting enviromental data right from your garden.
20 parts27
Questions
How big is the HeaterControl PCB?
It measures 32.8 × 24.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the HeaterControl use?
17 parts, built around the DS18B20 and BL654. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the HeaterControl KiCad files?
From the TheTosters/HeaterControl repository on GitHub, at the commit this page was made from: the board is hardware/universalSensor/HeaterControl.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the HeaterControl design in my own project?
Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).