

QASS PCB lowbar
QAZ-like for a BAE and 10u spacebar
- Size
- 219.1 × 110.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 104
- Nets
- 73
- Pads
- 722
- Tracks, vias
- 387, 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 21 Feb 2024
- Updated
- 29 Mar 2026
Overview
QASS PCB lowbar is an open-source printed circuit board by Technofrikus, from the Technofrikus/QASS repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 219.1 × 110.5 mm with 104 parts on 73 nets, routed with 387 tracks and 2 vias.
Its parts include 39 diodes, 8 switches, 5 connectors and 1 IC. It belongs with the keyboards and input boards and the RP2040 boards of this library.
README
README.mdQASS
QAZ-like for a BAE (Big Ass Enter) and 10u spacebar (7u+8u)

More pictures and infos at Moinboards. Buildguide.
There are three versions: normal, lowbar (Miao for FAK-Firmware) and lowbar (Gemini for QMK/Vial). The normal version has the spacebar on the normal PCB. The lowbar uses the PCB as a plate on the bottom row and adds a lower PCB.
- Only the lowbar version was tested and fully finished. Please check the normal version before ordering.
- Lowbar:
- v1.0 is tested and works with MIAO. XIAO would work as well but the pads on the underside I wanted to use are not GPIOs but only for a special serial protocol. So they cant be used.
- v1.1 is Untested, but I only made cosmetic changes, so should still work fine.
- Quark-Works made a fork and changed the MCU to a Gemini (rp2040 zero compatible). Thanks! You can find it here.
- v1.2 Used the fork by Quarks as a basis. Removed a little mistake and made some cosmetic changes.
- v1.3 the prvious version works, but the silkscreen of the diodes is not visible (orientation of diodes). Corrected this and changed the direction of one diode to be more consistent with the other ones around it.
The latest version has the lower spacebar. Break off the lower part of the PCB and put it under the bottom row. Add headers at the connection points.

Case
The 3D-printable case files are included now (March 2025). Can recommend making the plate from metal. Gives the build more weight and looks nice. Tested with brass and copper. Use the special version to make sure they will not warp during cutting (havent tested it without these, just a precaution). Print recommendations included, see txt file.
It is for the low-bar version only.
Firmware
- FAK config and info can be found on moinboards and here in the firmware folder.
- Vial/Qmk for the fork by Quark. Confirmed working.
BOM
Parts
104| Qty | Value | Footprint | References |
|---|---|---|---|
| 40 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1u | MX1, MX2, MX10, MX13, MX14, MX15, MX16, MX17, MX18, MX19, MX20, MX21, MX23, MX24, MX25, MX26 +24 |
| 39 | 1n4148 | TFL:Diode-dual | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +23 |
| 4 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J2, J3, J5, J6 |
| 4 | Val** | Silkscreen:starpattern | Ref**, Ref**, Ref**, Ref** |
| 2 | 5.5mm | PCM_marbastlib-various:mousebites_5p5mm_easysnap | MB5, MB5 |
| 2 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1.5u | MX11, MX44 |
| 2 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1.75u | MX22, MX31 |
| 2 | MX_stab | PCM_marbastlib-mx:STAB_MX_3u | S2, S3 |
| 2 | MX_stab | PCM_marbastlib-mx:STAB_MX_2u | S4, S5 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1.25u | MX12 |
| 1 | MX_stab | PCM_marbastlib-mx:STAB_MX_P_10u | S7 |
| 1 | MX_stab | PCM_marbastlib-mx:STAB_MX_2.75u | S8 |
| 1 | MX_stab | PCM_marbastlib-mx:STAB_MX_P_ISO | S9 |
| 1 | MX_stab | PCM_marbastlib-mx:STAB_MX_2.25u | S1 |
| 1 | RP2040-Matrix | PCM_marbastlib-xp-promicroish:RP2040-Matrix_AH | U2 |
More from Technofrikus/QASS
1- 2 layers219.1 × 80.4 mm

Similar boards
- 2 layers247.7 × 97.7 mm

Woagboard
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
104 parts915 - 2 layers141 × 90 mm

Chirp v2.4-pannel
Miceuz/PlantWateringAlarm
A soil humidity level sensor based on ATTINY44. Uses capacitive sensing.
104 parts367 - 2 layers25.7 × 25.7 mm

- 2 layers147 × 116 mm

- 2 layers60.5 × 110 mm

- 2 layers37 × 113.9 mm

- 2 layers127 × 221 mm

- 2 layers74 × 36 mm

Ch32v305-currentmonitor
cnlohr/cnhardware
My dumping grounds for all my kicad projects and random hardware bringup.
104 parts114
Questions
How big is the QASS PCB lowbar PCB?
It measures 219.1 × 110.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the QASS PCB lowbar use?
104 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the QASS PCB lowbar KiCad files?
From the Technofrikus/QASS repository on GitHub, at the commit this page was made from: the board is QASS_PCB_Zero_lowbar_Germini/QASS_PCB lowbar.kicad_pcb and its schematic QASS_PCB Lowbar/QASS_PCB lowbar.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the QASS PCB lowbar design in my own project?
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).