
ESP32-PoE Rev M
OLIMEX/ESP32-POE
ESP32 IoT development board with 100Mb Ethernet and 802.3 Power Over Ethernet (POE)

Desktop Pomodoro Timer based on ESP32 with LCD1602 (I2C), tactile buttons, buzzer, and KiCad hardware design
ESP32-Pomodoro Timer is an open-source printed circuit board by TamarHoory, from the TamarHoory/ESP32-Pomodoro-Timer repository on GitHub, published under the MIT licence. It is a 2-layer board with 6 parts on 48 nets.
It is built around the ESP32-WROVER-E(4MB). Its parts include 3 switches and 2 ICs. It belongs with the ESP32 and RISC-V boards of this library.
A standalone, tactile desktop Pomodoro productivity timer powered by an ESP32 microcontroller and a 16x2 I2C LCD (LCD1602) display. Complete with custom KiCad hardware schematics, (PCB layout currently in progress), and robust, non-blocking Arduino/PlatformIO firmware.
0x27 / 0x3F) and real-time visual progress bar.IDLE, RUNNING, PAUSED, and COMPLETED.millis().INPUT_PULLUP)..kicad_sch) and printed circuit board design (.kicad_pcb).ESP32-Pomodoro-Timer/
├── Hardware/ # KiCad electronics design files
│ ├── ESP32 Pomodoro Timer.kicad_sch # Schematic diagram
│ ├── ESP32 Pomodoro Timer.kicad_pcb # PCB routing and layout
│ └── ESP32 Pomodoro Timer.kicad_pro # KiCad project configuration
│
├── ESP32 Pomodoro Timer/ # PlatformIO embedded firmware
│ ├── include/ # Header declarations
│ ├── lib/ # Third-party libraries
│ │ └── LiquidCrystal_I2C/ # I2C LCD control library
│ ├── src/
│ │ └── main.cpp # Core application logic & state machine
│ ├── test/ # Unit tests
│ └── platformio.ini # PlatformIO environment configuration
│
├── .gitignore # Build and temporary files exclusion
├── diagram.json # Wokwi simulation diagram
├── wokwi.toml # Wokwi simulation configuration
└── README.md # Project documentation| Component | Pin / Terminal | ESP32 GPIO | Description |
|---|---|---|---|
| LCD1602 (I2C Backpack) | SDA | GPIO 21 | I2C Data Line (50 kHz clock rate) |
SCL | GPIO 22 | I2C Clock Line | |
VCC | VIN / 5V | Module power supply & backlight | |
GND | GND | Common ground | |
| Start / Pause Button | Pin 1 / Switch | GPIO 18 | Active-LOW (Internal INPUT_PULLUP) |
| Pin 2 / Switch | GND | Ground connection | |
| Reset Button | Pin 1 / Switch | GPIO 19 | Active-LOW (Internal INPUT_PULLUP) |
| Pin 2 / Switch | GND | Ground connection | |
| Set Time Button | Pin 1 / Switch | GPIO 23 | Active-LOW (Internal INPUT_PULLUP) |
| Pin 2 / Switch | GND | Ground connection | |
| Piezo Buzzer | Positive (+) | GPIO 25 | PWM tone signal |
| Negative (-) | GND | Ground connection |
Note on LCD Power: Most LCD1602 I2C backpacks require 5V (
VIN) for bright backlight and optimal character contrast. The I2C data lines (SDA/SCL) operate smoothly at 3.3V logic levels on the ESP32.
The firmware implements a responsive, non-blocking finite state machine displayed across 2 rows of 16 characters:
STATE_IDLE)Allows setting the session duration using the Set Time button:
+----------------+
|[READY] Set:25m|
|Time: 25:00 |
+----------------+STATE_RUNNING)Active countdown with elapsed ratio visual progress bar:
+----------------+
|FOCUS TIME... |
|24:12 [=== ] |
+----------------+STATE_PAUSED)Temporarily pauses countdown without losing elapsed progress:
+----------------+
|[PAUSED] |
|Time: 18:45 |
+----------------+STATE_COMPLETED)Fires when the timer reaches zero, accompanied by a triple-beep audio chime:
+----------------+
|*** TIME'S UP **|
|GREAT JOB! :D |
+----------------+Clone the repository:
git clone https://github.com/TamarHoory/ESP32-Pomodoro-Timer.git
cd ESP32-Pomodoro-TimerOpen in VS Code:
ESP32 Pomodoro Timer folder (or the root workspace).Build & Upload:
pio runpio run --target uploadMonitor Serial Output:
pio device monitorYou can test and run this project without physical hardware using the Wokwi simulator:
1. Make sure you have the **Wokwi Simulator** extension installed in VS Code.
2. Open the project folder in VS Code.
3. Open the `diagram.json` file, and click the **Play** button (or use the command palette `Wokwi: Start Simulator`) to run the interactive simulation with the virtual ESP32, LCD, and buttons.The Hardware/ folder contains native KiCad files:
ESP32 Pomodoro Timer.kicad_sch: Electrical schematic connecting the ESP32 Dev board, tactile buttons, buzzer, and I2C connector header.ESP32 Pomodoro Timer.kicad_pcb: 2-layer PCB layout with traces, component placements, and mounting holes.To export Gerber files for PCB manufacturing (JLCPCB, PCBWay, etc.):
ESP32 Pomodoro Timer.kicad_pro in KiCad..zip archive for ordering.Tamar Hoory
This project is open-source and available under the MIT License.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | ESP32-WROVER-E | PCM_Espressif:ESP32-DevKitC | U1 |
| 1 | RC1602A | Display:LCD-016N002L | U2 |
| 1 | RESET | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW2 |
| 1 | Set Time | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW3 |
| 1 | Start/Stop | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW1 |

OLIMEX/ESP32-POE
ESP32 IoT development board with 100Mb Ethernet and 802.3 Power Over Ethernet (POE)



Circuit-Digest/MLX90640-Thermal-Camera
An Open Source Thermal Imaging IR camera that you can build yourserlf

espena/broadcast-clock
Digital precision studio/broadcast masterclock with WiFi configuration, acts as local NTP server with accurate GPS time sync.

martinroger/ipodesp32
An iPod emulator for 2006-2013 BMW Mini Coopers that need Bluetooth


6 parts, built around the ESP32-WROVER-E(4MB). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the TamarHoory/ESP32-Pomodoro-Timer repository on GitHub, at the commit this page was made from: the board is Hardware/ESP32 Pomodoro Timer.kicad_pcb and its schematic Hardware/ESP32 Pomodoro Timer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).