
LibreVerter Controller
imendizabal/LibreVerter
Open Source Power Converter - Hardware Components

Modbus Protocol based Input/output board to control periphery
Modbus IO Board is an open-source printed circuit board by TAN-ASH, from the TAN-ASH/Modbus_I-O_Board_PCB repository on GitHub. It is a 2-layer board of 34.8 × 69.8 mm with 84 parts on 36 nets, routed with 424 tracks and 75 vias.
It is built around the ATMEGA328PB-AN, MAX3072EASA+ and LTV-206, with the PSM712-LF-T7, TPS7B6933QDCYRQ1 and B5819W-TP among its other parts. Its parts include 16 capacitors, 9 diodes, 8 resistors, 6 ICs and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Modbus Protocol based Input/output board to control periphery
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | TestPoint | TestPoint:TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | 12V, 12V, A, B, B, I1-1, I1-2, I2-1, I2-2, O1-1, O1-2, O2-1, O2-2, TP9, TP11, TP15 |
| 10 | CONN_01X01 | 1pin_niTin:1pin | , , , , , , e, e, e, e |
| 6 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | EN, GND, GND, GND, RX, TP18 |
| 5 | 100nF | Capacitor_SMD:C_0402_1005Metric | C4, C5, C11, C13, C14 |
| 4 | MountingHole | TestPoint:TestPoint_Plated_Hole_D3.0mm | H1, H2, H3, H4 |
| 3 | 4K7 | Resistor_SMD:R_0402_1005Metric | R1, R2, R14 |
| 3 | B5819W-TP | SamacSys_Parts:SOD3716X135N | D3, D6, D8 |
| 3 | D_TVS | Diode_SMD:D_SOD-323 | D5, D7, D9 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C1, C16 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C6, C7 |
| 2 | 330 | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | 4.7K | Resistor_SMD:R_0402_1005Metric | R6, R9 |
| 2 | 74279218 | SamacSys_Parts:BEADC3216X130N | FB1, FB2 |
| 2 | LOGO | logo:A1_logo | G***, G*** |
| 1 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 0.1uF35V | Capacitor_SMD:C_1206_3216Metric | C9 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | 10uF35V | SamacSys_Parts:CAPPM3528X210N | C8 |
| 1 | 10uH | Inductor_SMD:L_1206_3216Metric | L1 |
| 1 | 1uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C3 |
| 1 | 4.7uF | Capacitor_SMD:C_1206_3216Metric | C12 |
| 1 | 4.7uF10V | Capacitor_SMD:C_1206_3216Metric | C10 |
| 1 | 7.37MHz | SamacSys_Parts:ABLS373728MHZD4YT | Y1 |
| 1 | ATMEGA328PB-AN | SamacSys_Parts:QFP80P900X900X120-32N | IC1 |
| 1 | Conn_01x06_Male | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J1 |
| 1 | D | SamacSys_Parts:FDLL4448 | D1 |
| 1 | D_TVS | Diode_SMD:D_SMA | D4 |
| 1 | D_Zener | SamacSys_Parts:SOD3716X145N | D2 |
| 1 | LTV-206 | SamacSys_Parts:SOIC127P610X363-8N | IC5 |
| 1 | MAX3072EASA+ | SamacSys_Parts:SOIC127P600X175-8N | IC3 |
| 1 | PRG21BC4R7MM1RA | Snapeda:THRMC2012X110N | RT1 |
| 1 | PSM712-LF-T7 | SamacSys_Parts:PSM712LFT7 | U1 |
| 1 | SN74LVC2G14DBVRG4 | SamacSys_Parts:SOT95P280X145-6N | IC4 |
| 1 | TPS7B6933QDCYRQ1 | SamacSys_Parts:SOT230P700X180-4N | IC2 |
| 1 | Varistor | SamacSys_Parts:VARC3216X145N | RV1 |

imendizabal/LibreVerter
Open Source Power Converter - Hardware Components



greghulette/Wireless_Communication_Board-WCB
Repository for the Wireless Commuincation Board (WCB)


slemanz/chronolog
STM32-based temperature data logger with RTC, NOR flash storage, LCD and Wi-Fi. Hardware and firmware.

shorlee/TeleSTERN
The TeleSTERN Project is an Open Source Rocketry Flight Computer based on the TeleMega by Altus Metrum.

SurajSonawane2415/PCB-Design-STM32-Dev-Board
Custom STM32 Development (PCB) Board with an on-board SPI sensor (TC72).
It measures 34.8 × 69.8 mm and has 2 copper layers, 1.6 mm thick.
84 parts, built around the ATMEGA328PB-AN, MAX3072EASA+, LTV-206 and PSM712-LF-T7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the TAN-ASH/Modbus_I-O_Board_PCB repository on GitHub, at the commit this page was made from: the board is Modbus_IO_Board/Modbus_IO_Board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask TAN-ASH before reusing the design.