
Output.Panel R0.5.1 300x300 2layer step1 Modified
rusefi/hw_microRusEfi
microRusEfi board for rusEfi ECU

CAN module is an open-source printed circuit board by T00833, from the T00833/Anti-radar-PCB repository on GitHub. It is a 4-layer board of 100 × 75 mm with 52 parts on 81 nets, routed with 377 tracks and 78 vias.
It is built around the SN65HVD233QDRQ1, NEO-M9N-00B and LM5164QDDATQ1, with the L717SDE09PA4CH4F, NX2016SA-32MHZ-EXS00A-CS11336 and PESD1CAN-UX among its other parts. Its parts include 22 capacitors, 11 resistors, 4 ICs, 3 connectors and 2 diodes.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100nF | Capacitor_SMD:C_0805_2012Metric | C1, C4, C7, C8, C9, C12, C16, C17, C18, C19, C20, C21, C22, C23, C24 |
| 3 | 10kΩ | Resistor_SMD:R_0805_2012Metric | R2, R3, R4 |
| 2 | 2.2uF | SCK_Footprints:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3 |
| 2 | 56kΩ | Resistor_SMD:R_0805_2012Metric | R8, R10 |
| 1 | 0.5mA/40V/510mV (max) | Diode_SMD:D_SOD-123 | D3 |
| 1 | 100kΩ | Resistor_SMD:R_0805_2012Metric | R9 |
| 1 | 10Ω | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 1kΩ | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | 1nF | Capacitor_SMD:C_0201_0603Metric | C14 |
| 1 | 1uF | SCK_Footprints:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 22pF | Capacitor_SMD:C_01005_0402Metric | C11 |
| 1 | 240pF | Capacitor_SMD:C_01005_0402Metric | C15 |
| 1 | 27.4kΩ | Resistor_SMD:R_0805_2012Metric | R7 |
| 1 | 27nH | Inductor_SMD:L_0402_1005Metric | L3 |
| 1 | 30kΩ | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 330Ω | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 47uF | Antyradar_footprints:CAPC6153X670N | C13 |
| 1 | 47uH | Antyradar_footprints:NRS8040T470MJGK | L1 |
| 1 | Ant BT - 2450AT18D0100E | Antyradar_footprints:2450AT18D0100E_JOT | U3 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_CUI_PJ-036AH-SMT_Horizontal | J2 |
| 1 | Conn_Coaxial | Connector_Coaxial:SMA_Molex_73251-1153_EdgeMount_Horizontal | J4 |
| 1 | Jumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | JP1 |
| 1 | KW47B42ZB7AFTB | Antyradar_footprints:QFN50P700X700X90-49N-D | MCU1 |
| 1 | L717SDE09PA4CH4F | Antyradar_footprints:L717SDE09PA4CH4F | OBD-II_CONNECTOR1 |
| 1 | LED_Green | LED_SMD:LED_01005_0402Metric | GREEN1 |
| 1 | LM5164QDDATQ1 | Package_SO:HSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.1mm_ThermalVias | U2 |
| 1 | Maxell ML2032 | Battery:BatteryHolder_MYOUNG_BS-07-A1BJ001_CR2032 | BT2 |
| 1 | NEO-M9N | RF_GPS:ublox_NEO | GNSS_module1 |
| 1 | NX2016SA-32MHZ-EXS00A-CS11336 | Antyradar_footprints:NX2016SA_NDK | XTAL1 |
| 1 | PC817 | Package_DIP:DIP-4_W7.62mm | U1 |
| 1 | PESD1CAN-UX | Antyradar_footprints:PESD1CANUX | D2 |
| 1 | SN65HVD233QDRQ1 | Antyradar_footprints:SOIC127P600X175-8N | IC1 |
| 1 | Screw_Terminal_01x02 | Antyradar_footprints:CUI_TB002-500-02BE | J5 |
| 1 | TestPoint | TestPoint:TestPoint_Keystone_5000-5004_Miniature | TP2 |

rusefi/hw_microRusEfi
microRusEfi board for rusEfi ECU



v-cu/dpf-load-monitor-wide
ESP32-P4 diagnostic display for VAG diesels — live DPF and engine data over CAN (UDS) on a 3.19" ultra-wide AMOLED. Firmware, KiCad files, BOM and 3D enclosure.

romioRN/Dash6.8-hardware
wifi name "service", password 12345678, connect to 192.167.4.1

chrkir/hcv
Local Viessmann E3 CAN-bus to MQTT bridge for Vitocal heat pumps. Features Home Assistant Auto-Discovery, ESP32 firmware, and Open Hardware.

ksmola/PriusG2
Inverter control board for Toyota Prius Gen 2 (XW20) inverter. Some of the schematics are based on Johannes Huebner's work found here. Running openinverter firmware.

halbritt/fome-mc
FOME-MC integrated single-PCB motorcycle ECU (STM32H753 + 2x STM32F042 WBO)
It measures 100 × 75 mm and has 4 copper layers, 1.6 mm thick.
52 parts, built around the SN65HVD233QDRQ1, NEO-M9N-00B, LM5164QDDATQ1 and L717SDE09PA4CH4F. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the T00833/Anti-radar-PCB repository on GitHub, at the commit this page was made from: the board is CAN_module/CAN_module.kicad_pcb and its schematic CAN_module/CAN_module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask T00833 before reusing the design.