Skip to the content
2 layers34.5 × 35.3 mm24v-12v buck @ 3A, the printed circuit board in 3D

Independently developed a 24V-12V buck converter using the TPS563300 IC designed to operate at 3A. Performed calculations to find ideal component values for best performance while refering to the IC datasheet. Designed schematics and PCBs on KiCAD iterating through prototypes as I learned from mistakes.

Size
34.5 × 35.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
8
Pads
28
Tracks, vias
36, 3
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
5 Apr 2026
Updated
8 Apr 2026

Overview

24v-12v buck @ 3A is an open-source printed circuit board by SydneyDith, from the SydneyDith/Buck-Converter---TrickFire-Robotics repository on GitHub. It is a 2-layer board of 34.5 × 35.3 mm with 11 parts on 8 nets, routed with 36 tracks and 3 vias.

It is built around the TPS563300DRL. Its parts include 5 capacitors, 2 resistors, 2 connectors, 1 IC and 1 inductor. It belongs with the power boards of this library.

Main components

1

README

README.md

Buck Converter - Power Distribution (12V-24V @3A) - TrickFire Robotics

Independently developed a 24V-12V buck converter using the TPS563300 IC designed to operate at 3A for use in TrickFire Robotics power distribution system. Performed calculations to find ideal component values for best performance while referring to the IC datasheet. Designed schematics and PCBs on KiCAD iterating and refining prototypes as I learned from previous mistakes.

ParameterValue
Input Voltage24V
Output Voltage12V
Max Current3A

Schematic And PCB Design

Schematic Screenshot

To develop the buck converter schematic I frequently referred to the main operating IC's datasheet: datasheet

It provides formulas and specifications of the buck IC I used to develop this schematic. When selecting footprints for my components, I opted for the 0603 package when possible. For the resistors and capacitors, selecting the handsolder footprint made handsoldering my PCB much easier later on. In my first iteration of schematic design, I made the mistake of choosing an inductor footprint that was only rated for a current of ~250mA. When double checking my work, however, I found this mistake and quickly sought another component that could support my desired specifications of 3A. Luckily this fix was easy at this stage in the project, but if left overlooked, my final design wouldn't have worked as intended and cost the project time and money to fix. I quickly found a replacement and ensured my other components were rated for this current and voltage.

PCB Layout Prototype V1

Based on the datasheet, the following layout/placement strategies were employed:

  • Placed IC, inductor, and caps on the same side of the board.
  • Positioned input/output caps as close to the IC as possible.
  • Placed 0.1µF decoupling caps directly next to the power pins.
  • Kept the switching trace small and current loop small to minimize noise.
  • Positioned the FB divider near the pin and away from noisy power traces.

In my initial design, I emphasized the placement strategies listed above but once again failed to account for the 3A of current flowing through the buck. I used the default trace size of 0.2mm for my 24V input line when I should've used around 1.2mm to support the current. With the 0.2mm trace, my buck could only provide less than an amp of current. I stumbled upon this issue when doing research about PCB design and learned that when dealing with power distribution systems, trace width and trace size really matters. Initially, this wasn't something that I emphasized enough. Below is my revised pcb where I increased the trace size, adjusted placements, and created a ground plane:

Final PCB Layout

The followng image shows the 3D render of the PCB design above:

PCB Layout 3D Render

Results

Soldered Buck

When soldering the pcb, I found the greatest challenge was handsoldering the TPS563300 IC. It was about the size of two grains of rice side by side, and it was an 8 pin IC. However, with patience and some flux, I was able to solder the IC, esuring no shorts between legs. When soldering the big inductor, I found success in swapping my soldering iron's tip to a large chisel that transfered heat easily. The 0603 package parts were pretty straight forward. Using a fine gauge leaded solder made soldering these components easy.

Output of Buck Converter (24V Input)

Finally I was able to test my 24V-12V buck converter. As to not immediately damage the buck converter, I used a lab bench multimeter which has a very large internal resistance. When measuring the output voltage, I could ensure there would be a very small amount of current and could specifically measure the output voltage without the risk of damaging anything. I found 12.9V at the output, which seemed to be a good sign. This error could very well be attributed to component tolerances, inaccuracy in the IC, or filtering issues. If I desired a cleaner output, I would switch to more (expensive) tolerant resistors and improve input and output filtering.


Conclusion

My previous experience in pcb design had been in communication systems using the ATmega328p microcontroller and several sensors through I2C communication in my Heartrate Monitor Smartwatch. However, this project introduced me to basic power electronics and pcb deign strategies to employ when dealing with higher voltages and currents. In communication, I was dealing with digital electronics and the goal was signal integrity to ensure data reached the sensors. In power electronics, however, traces will burn if they aren't wide enough for the current, components must be strictly rated for the voltage and current, and component placements can have a large impact on the electromagnetic interference.

This project has served as a great introduction to one of the many subfields of Electrical Engineering where I have been able to apply and expand upon class concepts. I can't wait to dive deeper into the world of power electronics for future projects.

Parts

11
QtyValueFootprintReferences
310uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC3, C4, C5
20.1uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1, C2
2282837-2282837-2:TE_282837-2P1, P2
110kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR2
112uHInductor_SMD:L_Bourns_SRR1208_12.7x12.7mmL1
1140kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1
1TPS563300Package_TO_SOT_SMD:SOT-583-8U1

Similar boards

  • 4 layers104.2 × 59.7 mmCustom BMS, the printed circuit board in 3D

    Custom BMS

    SCFormulaElectric/USC-Electrical-Systems

    246 parts9
  • 4 layers51.5 × 89 mmIbScaleFeederLite, the printed circuit board in 3D

    IbScaleFeederLite

    ibScale/ibScaleFeederLite

    ibScale Lite Feeder for the LumenPNP

    89 partsCERN-OHL-S-2.0
  • 2 layers35 × 34.4 mmDrone power 2 screws, the printed circuit board in 3D

    Drone power 2 screws

    ISSUIUC/ISS-PCB

    Building custom flight computers

    38 parts33
  • 4 layers55 × 70 mmPcb 2 ninja, the printed circuit board in 3D

    Pcb 2 ninja

    AresEnsea/2526_Projet2A_AresCFR

    Ce repository GitHub regroupe l'ensemble des projets et documents réalisés par l'équipe Ares pour la Coupe de France de Robotique 2026.

    109 parts5
  • 2 layers89 × 113 mmVirgil Power, the printed circuit board in 3D

    Virgil Power

    da-penguin-guy/Proteus

    The Proteus is a modular collection of PCBs that will be used to develop the Virgil sound Protocol

    71 parts3
  • 2 layers45 × 85 mmPSU, the printed circuit board in 3D

    PSU

    velvia-fifty/AudioThings

    DIY audio-related projects of questionable quality and dubious utility; delivered in 30 minutes or less or the next one is free

    67 parts1
  • 2 layers60 × 30 mmController, the printed circuit board in 3D

    Controller

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    11 parts3kApache-2.0
  • 2 layers103 × 30.5 mmTS Front Endcap, the printed circuit board in 3D

    TS Front Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    11 parts1.3kMIT

Questions

How big is the 24v-12v buck @ 3A PCB?

It measures 34.5 × 35.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the 24v-12v buck @ 3A use?

11 parts, built around the TPS563300DRL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the 24v-12v buck @ 3A KiCad files?

From the SydneyDith/Buck-Converter---TrickFire-Robotics repository on GitHub, at the commit this page was made from: the board is KiCAD files/24v-12v buck @ 3A.kicad_pcb and its schematic KiCAD files/24v-12v buck @ 3A.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the 24v-12v buck @ 3A design in my own project?

Its repository states no licence, so its author keeps all rights: ask SydneyDith before reusing the design.