
Rgb to hdmi
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

It works by using a 4060 that triggers a 4020 on it's final output, since the 4020 is triggered on the falling edge it continues perfectly.
Resolution w3 is an open-source printed circuit board by Sushi-Mampfer, from the Sushi-Mampfer/resolution_hw_week_3 repository on GitHub. It is a 2-layer board of 92.4 × 61.3 mm with 33 parts on 44 nets, routed with 119 tracks and 0 vias.
Its parts include 13 resistors, 5 diodes, 5 transistors, 5 switches and 2 ICs.
A semi configurable alarm, you can set times from 1-15 hours. It's perfect, because it'll definitely make you wake up early.
It works by using a 4060 that triggers a 4020 on it's final output, since the 4020 is triggered on the falling edge it continues perfectly. And the last 4 outputs of the 4020 are 1/2/4/8 hour(s) (although an hour is a bit less than 58 minutes, because I couldn't use exact values). The buzzers signal is grounded by 4 different switches which are grounded by the 1/2/4/8 hour(s) pins. This allows you to put in any number from 1 to 15 hours. The reset switch grounds the buzzers input and powers the RESET pin on the 4060 and 4020.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R3, R4, R5, R6, R12 |
| 5 | 1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R7, R8, R9, R10, R13 |
| 5 | D | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2, D3, D4, D5 |
| 5 | NPN | Package_TO_SOT_THT:TO-92L_Inline_Wide | Q1, Q2, Q3, Q4, Q5 |
| 5 | SW_SPST | Button_Switch_THT:SW_PUSH_6mm | SW1, SW2, SW3, SW4, SW5 |
| 1 | 10u | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 125 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R11 |
| 1 | 4.7 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R2 |
| 1 | 4020 | Package_DIP:DIP-16_W7.62mm | U2 |
| 1 | 4060 | Package_DIP:DIP-16_W7.62mm | U1 |
| 1 | 47 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

mntmn/amiga2000-gfxcard
MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

Arrow-air/project-quiver
Project Quiver documentation, designs, and project artifacts.

ozel/DIY_particle_detector
A mobile low-cost spectrometer for measuring radioactivity and the energy of ionising radiation like alpha particles and electrons
BlueAndi/Pixelix
Full RGB LED matrix, based on an ESP32 and WS2812B LEDs or emulated LEDs on TFT.

jrsteensen/OpenHornet
OpenHornet 1:1 F/A-18C Simulator Repository

It measures 92.4 × 61.3 mm and has 2 copper layers, 1.6 mm thick.
33 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Sushi-Mampfer/resolution_hw_week_3 repository on GitHub, at the commit this page was made from: the board is src/kicad/resolution_w3.kicad_pcb and its schematic src/kicad/resolution_w3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Sushi-Mampfer before reusing the design.