I am making a PCB which allows you to connect to any device that doesn't have Bluetooth like a old TV or a car and connect an external Bluetooth device like you headphones or a speaker.
Bluetooth Audio Transmiter is an open-source printed circuit board by Shashvat1333, from the Shashvat1333/Bluetooth-Audio-Transmiter repository on GitHub. It is a 2-layer board of 107 × 29 mm with 20 parts on 61 nets, routed with 257 tracks and 16 vias.
It is built around the CH340C, ESP32-WROOM-32UE-N4 and AP2112K-3.3, with the BC817, SJ-3523-SMT-TR and UJ20-C-H-G-SMT-1-P16-TR among its other parts. Its parts include 7 capacitors, 5 resistors, 4 ICs, 2 transistors and 2 connectors. It belongs with the audio and music and radio and wireless boards and the ESP32 boards of this library.
A custom PCB I designed in KiCad that adds Bluetooth to anything with a headphone jack. Plug in an AUX cable, power it over USB-C, and stream to your wireless headphones.
Lots of good gear has no Bluetooth: an old TV, a record player, a treadmill, a car stereo with an AUX port. I wanted one small board that fixes that, so I designed it myself, from the schematic to the PCB layout.
What it does
Wired to wireless: Takes analog audio from a standard 3.5 mm AUX cable.
Clean conversion: A 24-bit stereo ADC turns the sound into digital audio.
Bluetooth streaming: An ESP32 sends the audio to your headphones or speaker.
Long range: An RP-SMA connector lets you attach an external antenna.
Real-world examples
Old TV: Watch late at night with AirPods, no cable across the room.
Record player: Listen to vinyl on wireless headphones.
Gym treadmill: No cable in your way while you run.
Schematic & PCB
Audio goes in through the AUX jack, gets digitized, and is sent out over Bluetooth:
text
AUX jack → PCM1808 (ADC) → ESP32 (Bluetooth) → your headphones
Part
What it does
ESP32-WROOM-32UE-N4
The brain: Bluetooth pairing and streaming
PCM1808PWR
Turns analog sound into digital (I2S) audio
AP2112K-3.3
Steps USB 5 V down to a steady 3.3 V
CH340C
USB-to-serial chip so you can upload code over USB-C
SJ-3523-SMT-TR
3.5 mm stereo input jack
Firmware
The ESP32 needs code before the board will do anything. You upload it once with the Arduino IDE.
Ceramic capacitors are tiny passive electronic components used here to filter out electrical noise on power rails and block DC voltage while letting audio signals pass through.
The AP2112K-3.3TRG1 is a low-dropout (LDO) voltage regulator used here to step down your incoming 5V power supply to a steady, clean 3.3V to power the ESP32 microcontroller and digital logic pins.
The ESP32 is a microcontroller used here to run firmware that receives the digital I2S audio stream from the PCM1808 and handles Wi-Fi or Bluetooth connectivity.
The CH340C is a USB-to-UART bridge IC used here to let your computer communicate with the ESP32 for programming and debugging via a standard USB-C cable.
That antenna and pigtail cable are used here to connect an external 2.4GHz antenna to the ESP32 module's IPEX connector for reliable Wi-Fi and Bluetooth signal reception.
The PCM1808PWR is a 24-bit stereo analog-to-digital converter (ADC) used here to convert your analog audio signals into digital I2S data for the ESP32.
The BC817 is a general-purpose NPN transistor used here to act as a switch—typically for driving indicator LEDs, controlling power lines, or handling USB reset signals in your circuit.
A resistor kit is a collection of various resistors with different resistance values used across your circuit for setting up pull-up/pull-down lines, limiting current to LEDs, and biasing transistors.
The culmination of all of my learning during the Spring '26 semester. All the way from making a simple dev board for the TAD5212 DAC, to making a RP2350 board, and now this. Everything combined on one 6-layer board.
A custom ESP32-based clock platform driving WS2812B/NeoPixel LED displays. Firmware and PCB are display-agnostic, supporting any addressable LED clock with minimal adjustments.
Neste repositório temos os principais arquivos que usamos para os 3 capítulos, Eletrônica, Mecânica e Software. Segue abaixo uma lista do que temos em cada uma das pastas:
45 parts2
Questions
How big is the Bluetooth Audio Transmiter PCB?
It measures 107 × 29 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Bluetooth Audio Transmiter use?
20 parts, built around the CH340C, ESP32-WROOM-32UE-N4, AP2112K-3.3 and BC817. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bluetooth Audio Transmiter KiCad files?
From the Shashvat1333/Bluetooth-Audio-Transmiter repository on GitHub, at the commit this page was made from: the board is hardware/Bluetooth-Audio-Transmiter.kicad_pcb and its schematic hardware/Bluetooth-Audio-Transmiter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bluetooth Audio Transmiter design in my own project?
Its repository states no licence, so its author keeps all rights: ask Shashvat1333 before reusing the design.