
BPC PRP microcontroller
Robotics-BUT/fenrir-project
https://robotics-but.github.io/fenrir-project/

https://robotics-but.github.io/fenrir-project/
BPC PRP rpi hat is an open-source printed circuit board by Robotics-BUT, from the Robotics-BUT/fenrir-project repository on GitHub, published under the MIT licence. It is a 2-layer board of 56 × 65 mm with 46 parts on 46 nets, routed with 383 tracks and 16 vias.
It is built around the DS3231MZ+ and WS2812B. Its parts include 16 resistors, 9 diodes, 6 connectors, 4 capacitors and 3 ICs. It belongs with the robots and motor control boards of this library.
The Fenrir Project is an open source of a multi purpose education robot dedicated for wide range of applications and usage in high-schools and universities.
The robot is based on Raspberry Pi 4 and Arduino Nano. The Raspberry Pi provides computational power, ROS2 support, WiFi connection and USB support. The Arduino Nano extends the PRi IOs and handles peripherals.
The development is currently still under development




Note: The sensors numbering goes from left to right
| Module A | Pin | Module B | Pin | Type | Length | Note |
|---|---|---|---|---|---|---|
| Battery 1 | - | PD Module | - | USB-C - USB-C | 15cm | - |
| Battery 2 | - | Raspberry Pi | - | USB-C - USB-C | 15cm | - |
| Raspberry Pi | - | Camera | - | CSI Cable | 10cm | - |
| Raspberry Pi | 3v3 | GPS | VCC | wire (blue) | 10cm | 3V3 |
| Raspberry Pi | GND | GPS | GND | wire (black) | 10cm | GND |
| Raspberry Pi | Rx | GPS | TxD | wire (purple) | 10cm | UART |
| Raspberry Pi | 5V | I2C Board | 5V | wire (red) | 8cm | 5V |
| Raspberry Pi | GND | I2C Board | GND | wire (black) | 8cm | GND |
| Raspberry Pi | SCL | I2C Board | SCL | wire (yellow) | 8cm | SCL |
| Raspberry Pi | SDA | I2C Board | SDA | wire (green) | 8cm | SDA |
| Raspberry Pi | - | LIDAR | - | USB-A - microUSB | 10cm | - |
| I2C Board | 5V | LCD | VCC | wire (red) | 8cm | 5V |
| I2C Board | GND | LCD | GND | wire (black) | 8cm | GND |
| I2C Board | SCL | LCD | SCL | wire (yellow) | 8cm | SCL |
| I2C Board | SDA | LCD | SDA | wire (green) | 8cm | SDA |
| I2C Board | 5V | Arduino | VCC | wire (red) | 15cm | 5V |
| I2C Board | GND | Arduino | GND | wire (black) | 15cm | GND |
| I2C Board | SCL | Arduino | SCL | wire (yellow) | 15cm | SCL |
| I2C Board | SDA | Arduino | SDA | wire (green) | 15cm | SDA |
| Arduino | US1 | Ultrasound 1 | Vcc | wire (red) | 10cm | 5V |
| Arduino | US1 | Ultrasound 1 | GND | wire (black) | 10cm | GND |
| Arduino | US1 | Ultrasound 1 | Echo/Trig | wire (blue) | 10cm | signal |
| Arduino | US2 | Ultrasound 2 | Vcc | wire (red) | 10cm | 5V |
| Arduino | US2 | Ultrasound 2 | GND | wire (black) | 10cm | GND |
| Arduino | US2 | Ultrasound 2 | Echo/Trig | wire (blue) | 10cm | signal |
| Arduino | US3 | Ultrasound 3 | Vcc | wire (red) | 15cm | 5V |
| Arduino | US3 | Ultrasound 3 | GND | wire (black) | 15cm | GND |
| Arduino | US3 | Ultrasound 3 | Echo/Trig | wire (blue) | 15cm | signal |
| Arduino | Line1 | Line Sens. 1 | VCC | wire (red) | 15cm | 5V |
| Arduino | Line1 | Line Sens. 1 | GND | wire (black) | 15cm | GND |
| Arduino | Line1 | Line Sens. 1 | A0 | wire (blue) | 15cm | signal |
| Arduino | Line2 | Line Sens. 2 | VCC | wire (red) | 15cm | 5V |
| Arduino | Line2 | Line Sens. 2 | GND | wire (black) | 15cm | GND |
| Arduino | Line2 | Line Sens. 2 | A0 | wire (blue) | 15cm | signal |
| Arduino | 5V | Encoder 1 | - | wire (yellow) | 20cm | 5V |
| Arduino | GND | Encoder 1 | - | wire (brown) | 20cm | GND |
| Arduino | EN1A | Encoder 1 | - | wire (red) | 20cm | A |
| Arduino | EN1B | Encoder 1 | - | wire (orange) | 20cm | B |
| Arduino | 5V | Encoder 2 | - | wire (yellow) | 20cm | 5V |
| Arduino | GND | Encoder 2 | - | wire (brown) | 20cm | GND |
| Arduino | EN2A | Encoder 2 | - | wire (red) | 20cm | A |
| Arduino | EN2B | Encoder 2 | - | wire (orange) | 20cm | B |
| Arduino | GND | PD Module | OUT- | wire (black) | - | - |
| Arduino | M1A | H-Bridge | IN3 | wire (yellow) | 20cm | PWM A+ |
| Arduino | M1B | H-Bridge | IN4 | wire (green) | 20cm | PWM A- |
| Arduino | M2A | H-Bridge | IN1 | wire (yellow) | 20cm | PWM B+ |
| Arduino | M2B | H-Bridge | IN2 | wire (green) | 20cm | PWM B- |
| PD Module | + | H-Bridge | +12V | wire (orange) | 15cm | 12V |
| PD Module | - | H-Bridge | GND | wire (black) | 15cm | GND |
| H-Bridge | OUT1+ | Motor 1 | - | wire (green) | 20cm | + |
| H-Bridge | OUT1- | Motor 1 | - | wire (blue) | 20cm | - |
| H-Bridge | OUT2+ | Motor 2 | - | wire (green) | 20cm | + |
| H-Bridge | OUT2- | Motor 2 | - | wire (blue) | 20cm | - |
| Role | Component | URL |
|---|---|---|
| Main Computer | RPi | link |
| Helper Microcontroller | Arduino Nano | link |
| 2x Battery | Powerbank 10000 mAh | link |
| Camera | RPi Camera v2 | link |
| GPS | NEO-7M module | link |
| 2D LiDAR | RPLiDAR A1M8 | link |
| LCD | HD44780 20x4 I2C | link |
| 3x Ultrasound | SRF-05 | link |
| 2x Line Sensor | TCRT5000 module | link |
| H Bridge | L298N module | link |
| Motor with Encoder | DG01D‐E | link |
| IMU | MPU6050 | link |
| Barometer | BME280 | link |
| Real Time Clock | DS3231 | link |
| ADC | ADS1115 | link |
| UWB (not yet) | DWM1000 | link |
| DC/DC Step Up | XL6009 | link |
| Power Delivery | USB-C PD module | link |
| Switch | link |
This work was created with the support of project RP182401001 under the PPSŘ 2025 program.
Adam Ligocki - adam.ligocki@vut.cz
Petr Šopák - petr.sopak@vut.cz
Jakum Minařík
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_SMD:R_1206_3216Metric | R1, R2, R3, R12, R13, R14 |
| 5 | 4k7 | Resistor_SMD:R_1206_3216Metric | R4, R5, R6, R7, R8 |
| 5 | ~ | LED_SMD:LED_1206_3216Metric | LED1, LED2, LED3, LED4, LED5 |
| 4 | 100n | Capacitor_SMD:C_1206_3216Metric | C1, C2, C3, C4 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 4 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4 |
| 3 | SW_DIP_x01 | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW1, SW2, SW3 |
| 2 | 1k8 | Resistor_SMD:R_1206_3216Metric | R10, R11 |
| 2 | 2k2 | Resistor_SMD:R_1206_3216Metric | R15, R16 |
| 1 | 220R | Resistor_SMD:R_1206_3216Metric | R9 |
| 1 | DS3231M | Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm | U3 |
| 1 | Fan_power | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-3_1x03_P2.54mm_Horizontal | J3 |
| 1 | I2C | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J4 |
| 1 | Power | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-3_1x03_P2.54mm_Horizontal | J2 |
| 1 | Power | TerminalBlock_RND:TerminalBlock_RND_205-00001_1x02_P5.00mm_Horizontal | J1 |
| 1 | RTC_BATT | Battery:BatteryHolder_Keystone_3000_1x12mm | BT1 |
| 1 | SPI | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-4_1x04_P2.54mm_Horizontal | J6 |
| 1 | UART | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J5 |
| 1 | ~ | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | U1 |
| 1 | ~ | my_footprint_lib:FAN_30 | U2 |

Robotics-BUT/fenrir-project
https://robotics-but.github.io/fenrir-project/

Robotics-BUT/fenrir-project
https://robotics-but.github.io/fenrir-project/

dhruv1859/CARVantaBAC
🧬 CARVanta Next-Generation Precision Oncology & AI CAR-T Cell Platform Interactive 3D Biological Digital Twin • 3D Neural Bridge • Sentinel HYDRA Biosensor

atireksd11/Astra-Companion
This repo holds the carrier PCB, the voice stack on the laptop, and notes for building Astra. Week 1 was the KiCad board.



mbelanger0/nixie-tube-clock
A nixie tube clock as a final PCB design project for ENGR3430: Eclectronics at Olin College of Engineering

nikolai2111/Multilayout-ESP-Wordclock_HW
Hardware (PCB) for an ESP32-C3 based word clock with support of different layouts and languages.
.kicad_pcb.jpg?size=s&soon)

zynthian/zynthian-hw
Zynthian hardware stuff: PCBs, schemes, parts specifications, pin assignment, ...
It measures 56 × 65 mm and has 2 copper layers, 1.6 mm thick.
46 parts, built around the DS3231MZ+ and WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Robotics-BUT/fenrir-project repository on GitHub, at the commit this page was made from: the board is pcbs/rpi_hat/BPC-PRP-rpi-hat.kicad_pcb and its schematic pcbs/i2c_board/BPC-PRP-i2c-board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).