Skip to the content
2 layers58 × 50 mmMagic Desk 64 512k reflashable Rev 3, the printed circuit board in 3D

Magic Desk 64 512k reflashable Rev 3

RetroNynjah/MD-SMD-reflashable1

Magic Desk 64 reflashable SMD version

Size
58 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
59
Pads
146
Tracks, vias
457, 72
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 Apr 2026
Updated
25 Apr 2026

Overview

Magic Desk 64 512k reflashable Rev 3 is an open-source printed circuit board by RetroNynjah, from the RetroNynjah/MD-SMD-reflashable repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 58 × 50 mm with 12 parts on 59 nets, routed with 457 tracks and 72 vias.

It is built around the 74AHCT244D, 74AHCT273D and 74HCT02D. Its parts include 4 capacitors, 4 ICs and 2 connectors.

Main components

3

README

readme.md

SMD version of Magic Desk cartridge

These cartridges are using SST39SF0x0 flash chips. Various sizes can be used, SST39SF010 (128 kB), SST39SF020 (256 kB) or SST39SF040 (512 kB). The chip can be flashed on board using a compatible EPROM programmer and the programming adapter that is included in this repository.

cartridge

Functional description

During normal use, the cartridge works as a regular Magic Desk cartridge.

I have added logic to make it possible to reprogram the chip without removing it from the cartridge PCB.
Reprogramming is done through a card edge adapter with an additional cable connected to a programming header for connecting the banked address pins and OE. The header for these banked address pins is connected directly to the flash chip but separated from the bank register using a 74244 buffer.
Since the cartridge is only operating in the ROML space, I have inverted the ROMH signal on the cartridge port and used that for enabling the buffer. The bank register is connected to the banked address pins whenever ROMH is HIGH (it is always HIGH when ROML is LOW). The programming adapter is disconnecting the bank register by permanently pulling ROMH to GND so that the address pins can be controlled by the programmer.

cartridge

The information on this page is for a Magic Desk cartridge for the C64 for the time being. A version for the C128 that works with the same programming adapter will be added at a later time.

Parts

12
QtyValueFootprintReferences
4100nCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1, C2, C3, C4
174AHCT244Package_SO:TSSOP-20_4.4x6.5mm_P0.65mmU4
174AHCT273Package_SO:TSSOP-20_4.4x6.5mm_P0.65mmU3
174HCT02Package_SO:TSSOP-14_4.4x5mm_P0.65mmU2
1C64 Expansion Portc64_expansion_port:C64 cartridge edge connectorJ1
1LOGOLOGOG***
1MountingHoleMountingHole:MountingHole_5mmH1
1SST39SF040Package_SO:TSOP-I-32_11.8x8mm_P0.5mmU1
1~Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalJ2

More from RetroNynjah/MD-SMD-reflashable

1

Similar boards

  • 4 layers133 × 93 mmProject GP8B, the printed circuit board in 3D

    Project GP8B

    JonathSpirit/GP8B

    G_Processor8Bits a homemade without any microcontroller 8bits processor

    110 parts
  • 4 layers170.1 × 170.1 mmOtterX, the printed circuit board in 3D

    OtterX

    RetroRemake/OtterX

    8-Bit computer compatible with Commander X16

    188 parts40CERN-OHL-W-2.0
  • 4 layers160 × 100 mmJ11HackPlus V2, the printed circuit board in 3D

    J11HackPlus V2

    TechPaula/DCJ11Hack-

    DCJ11 Hack+ related boards and code

    91 parts7
  • 4 layers304.8 × 330.2 mm2000ATX, the printed circuit board in 3D

    2000ATX

    jasonsbeer/Amiga-2000-EATX

    An Amiga 2000 PCB in the EATX form factor.

    614 parts200GPL-3.0
  • 6 layers304.8 × 243.8 mmAmigaPCI MainBoard, the printed circuit board in 3D

    AmigaPCI MainBoard

    AmigaPCI/AmigaPCI-MainBoard

    Amiga with Native PCI Bus

    748 parts135
  • 4 layers60 × 106.5 mmBeats, the printed circuit board in 3D

    Beats

    marangisto/Beats

    Programmable Clock Sequencer

    123 parts3MIT
  • 2 layers100 × 100 mmProtoCV, the printed circuit board in 3D

    ProtoCV

    marangisto/ProtoCV

    Prototype Precision CV

    142 parts2MIT
  • 4 layers100 × 70.8 mmKia Arm Ctrl, the printed circuit board in 3D

    Kia Arm Ctrl

    OLYPTEA/Kia

    Bras Robotique Open Source

    137 parts1MIT

Questions

How big is the Magic Desk 64 512k reflashable Rev 3 PCB?

It measures 58 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Magic Desk 64 512k reflashable Rev 3 use?

12 parts, built around the 74AHCT244D, 74AHCT273D and 74HCT02D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Magic Desk 64 512k reflashable Rev 3 KiCad files?

From the RetroNynjah/MD-SMD-reflashable repository on GitHub, at the commit this page was made from: the board is md64_smd_reflashable/rev3/kicad-schematics/Magic Desk 64 512k reflashable Rev 3.kicad_pcb and its schematic md64_smd_reflashable/rev3/kicad-schematics/Magic Desk 64 512k reflashable Rev 3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Magic Desk 64 512k reflashable Rev 3 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).