4 layers30 × 32 mm
Driver dual tmc2160
calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers
145 parts25
2 layers83.2 × 48.3 mm
Dronelight
ReclaimerLabs/Dronelight2A 100 W LED spotlight for your drone
- Size
- 83.2 × 48.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 81
- Nets
- 94
- Pads
- 361
- Tracks, vias
- 1,263, 357
- Pours
- 15
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 10 May 2016
- Updated
- 29 Nov 2017
Overview
Dronelight is an open-source printed circuit board by ReclaimerLabs, from the ReclaimerLabs/Dronelight repository on GitHub. It is a 2-layer board of 83.2 × 48.3 mm with 81 parts on 94 nets, routed with 1,263 tracks and 357 vias.
It is built around the LPS22HB, SPK0415HM4H-B-7 and DMT6016LSS, with the FSV8100V among its other parts. Its parts include 31 capacitors, 20 resistors, 8 crystals, 7 connectors and 5 ICs. It belongs with the nRF52 and nRF5x boards of this library.
Main components
4
LPS22HB
HLGA-10(2x2)-40℃~+85℃ 0.1hpa 0.1hpa 1.7V~3.6V 1uA 26Kpa~1.26bar I2C、SPI On-chip temperature compensation、Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Integrated signal amplifier、On-chip temperature output HLGA-10(2x2) Pressure Sensors ROHSSTMicroelectronicsPressure Sensors
SPK0415HM4H-B-7
--26dB 1.6V~3.6V 61dB 650uA Omnidirectional - MEMS Microphones ROHSKnowlesMEMS Microphones
DMT6016LSS
SO-81 N-channel 17nC@10V 2.1W 2.5V 27pF 282pF 28mΩ@4.5V 60V 864pF 9.2A N-Channel SO-8 MOSFETs ROHSDiodes IncorporatedMOSFETs
FSV8100V
TO-277-3-55℃~+150℃ 1 Independent 100V 150A 50uA@100V 670mV@8A 8A TO-277-3 Schottky Diodes ROHSonsemiSchottky Diodes
Parts
81| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0.1uF | Capacitors_SMD:C_0402 | C16, C17, C18, C19, C23, C30, C31 |
| 6 | 100k | Resistors_SMD:R_0603 | R6, R7, R11, R17, RT1, RT2 |
| 5 | 4.7uF | Capacitors_SMD:C_0805 | C7, C14, C21, C22, C29 |
| 4 | MTHOLE | Reclaimer_Labs:MountingHole_3.5mm_Pad_Via | X1, X2, X3, X4 |
| 3 | 10uF | Capacitors_SMD:C_1206 | C1, C2, C3 |
| 3 | 1k | Resistors_SMD:R_0603 | R12, R13, R14 |
| 3 | 1uF | Capacitors_SMD:C_0603 | C15, C20, C27 |
| 3 | HEATSINK | Reclaimer_Labs:573100D00010G | X5, X6, X7 |
| 2 | 10k | Resistors_SMD:R_0603 | R10, R18 |
| 2 | 18k | Resistors_SMD:R_0603 | R3, R15 |
| 2 | 3.3nH | Capacitors_SMD:C_0402 | L2, L3 |
| 2 | 4.7uF | Capacitors_SMD:C_1206 | C4, C5 |
| 2 | 8.2pF | Capacitors_SMD:C_0402 | C12, C13 |
| 2 | DMT6016 | Reclaimer_Labs:POWERDI5060-8 | Q1, Q2 |
| 2 | DNP | Capacitors_SMD:C_0402 | C24, C25 |
| 1 | 0.0005R | Reclaimer_Labs:CST0612 | R8 |
| 1 | 0.01uF | Capacitors_SMD:C_0603 | C6 |
| 1 | 0.5pF | Capacitors_SMD:C_0402 | C11 |
| 1 | 0.8pF | Capacitors_SMD:C_0402 | C10 |
| 1 | 1.2pF | Capacitors_SMD:C_0402 | C9 |
| 1 | 1000pF | Capacitors_SMD:C_0603 | C8 |
| 1 | 100pF | Capacitors_SMD:C_0402 | C26 |
| 1 | 15k | Resistors_SMD:R_0603 | R5 |
| 1 | 1N4148 | Diodes_SMD:D_SOD-123 | D2 |
| 1 | 22uH | Reclaimer_Labs:Inductor_DR127 | L1 |
| 1 | 28.7k | Resistors_SMD:R_0603 | R9 |
| 1 | 32MHz | Reclaimer_Labs:Crystal_SMD_2016-4pin_2.0x1.6mm | Y1 |
| 1 | 39mR | Resistors_SMD:R_0603 | R4 |
| 1 | 680k | Resistors_SMD:R_0603 | R1 |
| 1 | 750k | Resistors_SMD:R_0603 | R16 |
| 1 | 825k | Resistors_SMD:R_0603 | R2 |
| 1 | AP2204 | Reclaimer_Labs:SOT89-3 | U3 |
| 1 | ARM_Debug | Reclaimer_Labs:HEADER_SMT_02x05_1.27MM_POL | J3 |
| 1 | CONN_01X04 | Reclaimer_Labs:Header_04x01_2.5mm_RA | J1 |
| 1 | CONN_01X06 | Socket_Strips:Socket_Strip_Straight_1x06_Pitch2.54mm | J6 |
| 1 | CONN_02X06 | Socket_Strips:Socket_Strip_Straight_2x06_Pitch2.54mm | J7 |
| 1 | DNP | Capacitors_SMD:C_0603 | C28 |
| 1 | FSV8100V | Reclaimer_Labs:TO-277_3L_Diode | D1 |
| 1 | LPS22HB | Reclaimer_Labs:LGA10R50P2X3_200X200X80 | U5 |
| 1 | LT3755-2-MSE | Housings_SSOP:MSOP-16-1EP_3x4mm_Pitch0.5mm | U1 |
| 1 | Photo_Trans | Reclaimer_Labs:Photo_Trans_ALS-PT19-315C | Q3 |
| 1 | RGB LED 3228 SMD PLCC-4 | Reclaimer_Labs:PLCC4 | D3 |
| 1 | SAFETY | Socket_Strips:Socket_Strip_Straight_1x02_Pitch2.54mm | J2 |
| 1 | SB-NC | Reclaimer_Labs:SB-NC | SB1 |
| 1 | SPK0415HM4H-B | Reclaimer_Labs:SPK0415HM4H-8 | U4 |
| 1 | USB_OTG | Reclaimer_Labs:USB_Micro-B_10118194-0001LF | J5 |
| 1 | XT30 | Reclaimer_Labs:XT30 | J4 |
| 1 | nrf52840 | Reclaimer_Labs:AQFN73 | U2 |
Similar boards
- 6 layers39.5 × 39.5 mm
P4eregrine
anticitizn/p4eregrine
All-in-one ESP32 P4-based drone ESC, flight controller, and video processor
359 parts21 - 4 layers68.8 × 90.3 mm
Horizon
Horizon-Avionics/Horizon-H1
Building a fully open-source flight computer for amateur rocketry!
173 parts17 - 8 layers38 × 38 mm
Kolibri v0.5
bastian2001/Kolibri-FC-Hardware
Hardware for the Kolibri Flight Controller. 30mm/20mm FC with RP2350 + ELRS onboard
221 parts8GPL-3.0 - 2 layers100 × 70 mm
- 4 layers23.4 × 25.4 mm
Low Power LoRa
SorenGilkeyJohnson/LowLoRa
A solar powered, batteryless LoRa (expandable) sensor node powered from a supercapacitor charged by a small solar cell using an energy harvester.
70 parts3CERN-OHL-S-2.0 - 4 layers40 × 75 mm
CUR flight computer 25-26
CU-Rocketry/flight_computer
Competition Flight Computer Module 25-26
169 parts1 - 2 layers75 × 40.5 mm
Questions
How big is the Dronelight PCB?
It measures 83.2 × 48.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Dronelight use?
81 parts, built around the LPS22HB, SPK0415HM4H-B-7, DMT6016LSS and FSV8100V. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dronelight KiCad files?
From the ReclaimerLabs/Dronelight repository on GitHub, at the commit this page was made from: the board is electrical/dronelight.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dronelight design in my own project?
Its repository states no licence, so its author keeps all rights: ask ReclaimerLabs before reusing the design.