Skip to the content
6 layers66.4 × 66.5 mmNU180, the printed circuit board in 3D

A reverse-engineered replacement for the U180 hybrid in the HPAK 3458A DVM.

Size
66.4 × 66.5 mm
Copper layers
6
Thickness
2.22 mm
Parts
115
Nets
113
Pads
457
Tracks, vias
969, 291
Pours
6
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
24 Sep 2025
Updated
27 Aug 2026

Overview

NU180 is an open-source printed circuit board by NuZondar, from the NuZondar/NU180 repository on GitHub. It is a 6-layer board of 66.4 × 66.5 mm with 115 parts on 113 nets, routed with 969 tracks and 291 vias.

It is built around the ADG734BRU and SN74LVC1GU04DBV. Its parts include 61 resistors, 31 capacitors, 10 ICs and 1 connector. It belongs with the FPGA and CPLD boards of this library.

Main components

2

README

README.md

NU180

A reverse-engineered replacement for the U180 hybrid in the Hewlett-Packard / Agilent / Keysight 3458A DVM.

Briefly, the custom "U180" hybrid in the 3458A is infamously prone to excessive drifting or outright failure, but is absolutely unavailable. NU180 is a drop-in replacement for that hybrid. Still under development, its performance falls slightly short of an original U180, e.g. noise performance is ~20-30% higher than spec, but it thus provides at least 8 digits conversion (within 2x of 8.5 digits), which is infinitely better than a dead or dying machine!

Some notes:

The new Version 1.1 files are denoted "v11" in their names.

The layout requires 6 layers. Choose a thin stack-up - that is, thinner core layers - if available.

Choose the best resistors you can find, especially for their TCR (temperature coefficient of resistance). In particular, the use of low TCR bulk-foil resistors for at least the 50k and most-critical 80k's are recommended for best temperature stability.

The footprints for the critical 80k's allow choosing either large 2512 surface-mount resistors, or else through-hole resistors (same for the 50k). These are intended for builders who are using bulk-foil resistors (80k's only come in 2512 size). You can edit the files to delete the unused footprints or else leave them in place. Another option for the 50k and 80k resistors is to edit the files to substitute a small array of series or parallel resistors. There's room for up to 4 each, e.g. 4x 20k in series for the 80k's, etc.

You also have the option of using voltage regulation on the flip-flop and inverter (recommended), or else using unregulated 5V, chosen via jumpers. The schematic shows parts suitable for 3.3V operation, but other parts may allow operation down to 2.5V. The lower-voltage regulation should help keep noise down.

The 100k resistors to ground are optional and need not be included unless some problem is seen.

Debugging: The 3458A is a very sensitive instrument that can be quite fussy about error codes. At least in earlier versions, builders have sometimes found that changing the value of the series resistors (the 100 Ohm ones) up or down, e.g. to 33 or 220 Ohms, can help. Usually, only the four switch control lines associated with the 80k resistors (S5, S7, S9, S11) might need tuning. Another hack that has sometimes helped is adding a small capacitor (5-10 pF) in parallel with the R140 resistor on the A3 board.

There is extensive discussion of this project in the metrology section of EEVblog. Many people contributed their knowledge and experience towards its success, including MiDi, DB4UCH, wanghar, Kleinstein and others.

Good luck!

Parts

115
QtyValueFootprintReferences
21100Resistor_SMD:R_0603_1608MetricR27, R28, R29, R30, R31, R37, R38, R39, R40, R41, R42, R43, R44, R46, R47, R48 +5
1610uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3, C4, C6, C7, C8, C9, C10, C11, C12, C15, C21, C23, C25, C26, C30, C31
140.1uCapacitor_SMD:C_0603_1608MetricC1, C2, C13, C14, C16, C17, C18, C19, C20, C22, C24, C27, C28, C29
13100kResistor_SMD:R_0603_1608MetricR32, R33, R34, R35, R36, R62, R63, R64, R65, R66, R67, R68, R69
5TestPointConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalGND, GND, GND, GND4, VDD
420kResistor_SMD:R_0805_2012MetricR7, R11, R22, R26
480kResistor_SMD:R_0805_2012MetricR5, R10, R21, R25
480kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_VerticalR4, R8, R19, R23
480kResistor_SMD:R_2512_6332MetricR6, R9, R20, R24
4ADG734Package_SO:TSSOP-20_4.4x6.5mm_P0.65mmU2, U3, U5, U8
337.5kResistor_SMD:R_0805_2012MetricR12, R15, R16
3Ferrite Bead or ShortCapacitor_SMD:C_0603_1608MetricFB1, FB2, FB3
216.7kResistor_SMD:R_0805_2012MetricR13, R14
2Jumper_3_OpenJumper:SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mmJP1, JP2
2TLV70033_SOT23-5Package_TO_SOT_SMD:SOT-23-5U4, U9
110kResistor_SMD:R_0805_2012MetricR18
124kResistor_SMD:R_0805_2012MetricR17
133Resistor_SMD:R_0603_1608MetricR45
147uCapacitor_SMD:C_1206_3216MetricC5
150kResistor_SMD:R_2512_6332MetricR1
150kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_VerticalR2
150kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR3
1ATF1502ASPackage_QFP:TQFP-44_10x10mm_P0.8mmU6
1Conn_01x06_PinConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ1
1LT5400-1Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.68x1.88mmRN2
1LT5400-6Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.68x1.88mmRN1
1SN54LVTH574Package_SO:TSSOP-20_4.4x6.5mm_P0.65mmU10
1SN74LVC1GU04Package_TO_SOT_SMD:SOT-353_SC-70-5U7
1~AAALIB:U180PINSU1

More from NuZondar/NU180

1
  • 6 layers69.8 × 66.2 mmNU180v11, the printed circuit board in 3D

    NU180v11

    NuZondar/NU180

    A reverse-engineered replacement for the U180 hybrid in the HPAK 3458A DVM.

    105 parts10

Similar boards

  • 2 layers66 × 41.9 mmVideo timing board, the printed circuit board in 3D

    Video timing board

    Batperson/video_timing_board

    Development board to extract timing and subcarrier signals from a PAL or NTSC video source.

    45 parts6MIT
  • 2 layers29 × 14 mmNOTGATE, the printed circuit board in 3D

    NOTGATE

    Jetsama/DigitalLogicProject

    Physical representation of digital logic gates using PCBs

    11 parts2
  • 2 layers230.4 × 233.5 mmBkm-68x simple, the printed circuit board in 3D

    Bkm-68x simple

    skumlos/bkm-68x-simple

    Simplified BKM-68X

    216 parts7
  • 2 layers87 × 45 mmTau v2, the printed circuit board in 3D

    Tau v2

    decency131/tau

    tau is a pitch-to-MIDI instrument pedal

    69 parts2WTFPL
  • 2 layers50 × 58 mmHS2026-1D curvature, the printed circuit board in 3D

    HS2026-1D curvature

    cornell-happi-lab/HS2026-1D-curvature

    Surface curvature affects tactile sensor's reading but is often not considered in the calibration process. We propose a curvature-aware calibration pipeline, with full resources (STL, schematics, code, and guides) for…

    27 parts1MIT
  • 2 layers23.5 × 23.5 mmMeasure board v3, the printed circuit board in 3D

    Measure board v3

    aechoi/smart-suction

    Repository for evaluating data collected for the smart suction cup project.

    19 parts
  • 4 layers88.9 × 97 mmVideo thingy, the printed circuit board in 3D

    Video thingy

    C0DE-Z/LOUD

    A open source Analog video Destructor and Dirty mixer

    56 parts

Questions

How big is the NU180 PCB?

It measures 66.4 × 66.5 mm and has 6 copper layers, 2.22 mm thick.

What parts does the NU180 use?

115 parts, built around the ADG734BRU and SN74LVC1GU04DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the NU180 KiCad files?

From the NuZondar/NU180 repository on GitHub, at the commit this page was made from: the board is NU180.kicad_pcb and its schematic NU180.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the NU180 design in my own project?

Its repository states no licence, so its author keeps all rights: ask NuZondar before reusing the design.