

D Class Amp
ECEN405 Class-D amplifier group project
- Size
- 180 × 65 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 99
- Nets
- 55
- Pads
- 339
- Tracks, vias
- 289, 456
- Pours
- 244
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 21 Jul 2021
- Updated
- 20 Nov 2021
Overview
D Class Amp is an open-source printed circuit board by Niels-Clayton, from the Niels-Clayton/D-Class_Amplifier repository on GitHub. It is a 2-layer board of 180 × 65 mm with 99 parts on 55 nets, routed with 289 tracks and 456 vias.
It is built around the IR21834PBF, LM324 and LMV393, with the PHP23NQ11T and SMD1150PL-TP among its other parts. Its parts include 24 capacitors, 20 resistors, 7 ICs, 4 transistors and 2 diodes. It belongs with the audio and music boards of this library.
Main components
5IR21834PBF
DIP-14-40℃~+150℃ 1.4A 1.8A 10V~20V 1mA 2 20ns 40ns Half-Bridge IGBT、MOSFET Interleaved conduction protection、Dead-time control DIP-14 Gate Drivers ROHSInfineon TechnologiesGate Drive ICsLM324
SOP-14-1.5V~10V 0℃~+70℃ 24V 250nA 3V~20V 4 40mA 50nA 700uA 7mV 80dB SOP-14 Operational Amplifier ROHSHXY MOSFETOperational AmplifierLMV393
SOP-8-55℃~+125℃ 0.8uV/℃ 1.8V~5.5V 1pA 2 2pA 50uA 7V 800uV 850ns CMOS Open-drain SOP-8 Comparators ROHSTECH PUBLICComparatorsPHP23NQ11T
TO-220AB1 N-channel 100W 110V 140pF 22nC 23A 3V 49mΩ@10V 830pF 85pF N-Channel ±20V TO-220AB MOSFETs ROHSNexperiaMOSFETsSMD1150PL-TP
SOD-123FL1 Independent 150V 1A 30A 500uA@150V 850mV@1A SOD-123FL Schottky Diodes ROHSMicro Commercial ComponentsSchottky Diodes
README
README.mdD-Class Amplifier
ECEN405 Class-D amplifier group project
Team members:
- Daniel Eisen
- Nickolai Wolfe
- Niels Clayton
Input Filter Stage
- The input stage will use two active filters, a 10Hz corner frequency high pass filter, and a 200Hz corner frequency low pass filter. This will provide an overall filter passband of 10Hz - 200Hz.
S-PWM Generation
-
It is important to be able to effectively filter out the switching frequency of the sinusoidal pulse width modulated (SPWM) signal output. because of this, we want to ensure that the switching frequency is at least two decades above the maximum output frequency. This will ensure an attenuation of at least 40dB of the switching noise by the output filter.
-
Our output frequency range is 10Hz - 200Hz. To achieve the required attenuation of the switching frequency, it will nee to be 20kHz.
Power Stage
- 2x IR21834PBF drivers
- V_offset: 600V max
- I_o+-: 1.4A/1.8A
- T_on/off: 180ns/220ns
- MT: 35ns
- V_cc: 10-20V (single)
- V_in: Vss+5V
- 4x PHP23NQ11T,127 Fets
- minimum BV_dss of 45V
- Actual: 110V
- Gate Charge Qg: 10nC
- Rdson: 49m
https://www.infineon.com/dgdl/Infineon-Using_Monolithic_Voltage_Gate_Drivers-AN-v01_00-EN.pdf?fileId=5546d462584d1d4a01585242c11947b1
Output filter
Signal freq max of 200Hz, Switching frequency of ~25kHz Place corner frequency of filter at 2kHz (decade centred) mes
https://datasheets.maximintegrated.com/en/ds/MAX4295.pdf
Figure 4c. Alternate Balanced 2-Pole Filter
Balanced 2-Pole (Figure 4b): A balanced 2-pole filter does not have the common- mode swing problem of the single-ended filter. C = 2 / (√2 ✕ RL ✕ ωo), L = (√2 ✕ RL)/(2 ✕ ωo); choosing fo = 30kHz and RL = 4Ω, C1a = C1b = 2.0μF, L1a = L1b = 15μH. A single capacitor connected across RL, with a value of CL = 1/(√2 ✕ RL ✕ ωo), can be used in place of C1a and C1b. However, the configuration as shown gives an improved rejection to common-mode signal compo- nents of OUT+_ and OUT-_. If the single capacitor scheme is used, additional capacitors (Ca and Cb) can be added from each side of RL, providing a high-fre- quency short to ground (Figure 4c). These capacitors should be approximately 0.2 ✕ CL.
Parts
99| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R101, R102, R201, R204, R301, R501, R506 |
| 5 | 100n 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C201, C204, C208, C301, C303 |
| 4 | 10 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R502, R503, R504, R505 |
| 4 | 10u 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C101, C102, C501, C504 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_ISO14580_Pad | H105, H106, H107, H108 |
| 4 | PHP23NQ11T | PHP23NQ11T:PHP23NQ11T | Q501, Q502, Q503, Q504 |
| 3 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R302, R303, R304 |
| 2 | 0.47u 50V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C502, C503 |
| 2 | 100u 6.3V | Capacitor_SMD:CP_Elec_4x5.4 | C106, C202 |
| 2 | 150u | IND_HCTI-150-5.0:IND_HCTI-150-5.0 | L401, L402 |
| 2 | 1u 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C103, C105 |
| 2 | 1u 50V | Capacitor_SMD:CP_Elec_4x5.4 | C401, C402 |
| 2 | IR21834 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U501, U502 |
| 2 | SMD1150PL-TP | Diode_SMD:D_SOD-123F | D501, D502 |
| 1 | 1.2u 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C207 |
| 1 | 1.5k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R205 |
| 1 | 1000u 50V | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C104 |
| 1 | 10u 700V | C4AQJLU5100M19J:C4AQJLU5100M19J_film_capacitor | C403 |
| 1 | 150n 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C203 |
| 1 | 15k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R208 |
| 1 | 15n 16V | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | C302 |
| 1 | 1k | Potentiometer_THT:Potentiometer_Vishay_T73YP_Vertical | RV302 |
| 1 | 2.2u 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C205 |
| 1 | 2.4k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R206 |
| 1 | 20k | Potentiometer_THT:Potentiometer_Vishay_T73YP_Vertical | RV201 |
| 1 | 4.3k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R202 |
| 1 | 5.6k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R203 |
| 1 | 5k | Potentiometer_THT:Potentiometer_Vishay_T73YP_Vertical | RV301 |
| 1 | 680n 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C206 |
| 1 | 8.2k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R207 |
| 1 | Audio In | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP103 |
| 1 | AudioJack2 | CUI_MJ-63022A:CUI_MJ-63022A | J102 |
| 1 | DC_Offset | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP201 |
| 1 | Filter_bypass | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP201 |
| 1 | GND | MountingHole:MountingHole_3mm_Pad_Via | H102 |
| 1 | GNDS | MountingHole:MountingHole_3mm_Pad_Via | H104 |
| 1 | Gain_Stage | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP202 |
| 1 | HO | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP501 |
| 1 | Input Filter | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP104 |
| 1 | Input Signal | silk_art:sine | G101 |
| 1 | LM324 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U201 |
| 1 | LMV393 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U302 |
| 1 | LO | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP502 |
| 1 | MCP1799T-5002H_TT | Package_TO_SOT_SMD:SOT-23_Handsoldering | U102 |
| 1 | NCP1117-12_TO252 | Package_TO_SOT_SMD:TO-252-2 | U101 |
| 1 | Net-Tie_2 | NetTie:NetTie-2_SMD_Pad2.0mm | NT101 |
| 1 | Output Signal | silk_art:sine | G103 |
| 1 | P_IN | Connector_BarrelJack:BarrelJack_Horizontal | J101 |
| 1 | P_Out | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP107 |
| 1 | Power GND | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP101 |
| 1 | S-PWM | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP105 |
| 1 | SIG | MountingHole:MountingHole_3mm_Pad_Via | H103 |
| 1 | SPWM | silk_art:SPWM | G102 |
| 1 | Signal GND | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP102 |
| 1 | Speaker | Speaker:Speaker | LS101 |
| 1 | Speaker_Out | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP109 |
| 1 | Square | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP301 |
| 1 | Square Wave | silk_art:square | G105 |
| 1 | TL972 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U301 |
| 1 | Thumb | silk_art:thumb | G104 |
| 1 | Triangle | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP302 |
| 1 | Triangle Wave | silk_art:triangle | G106 |
| 1 | VDD | MountingHole:MountingHole_3mm_Pad_Via | H101 |
| 1 | ~HO | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP503 |
| 1 | ~LO | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP504 |
| 1 | ~P_Out | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP108 |
| 1 | ~S-PWM | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP106 |
| 1 | ~Speaker_Out | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP110 |
Similar boards
- 2 layers

- 2 layers43.2 × 47 mm

Current sink or swim
ALeggeUp/current-sink-or-swim
Project work from The Online Electronics Aprenticeship program at Contextual Electronics
29 partsCC-BY-SA-4.0 - 2 layers113 × 86 mm

- 2 layers89 × 55.5 mm

Mintypcb
jackw01/pi-tin
Open source raspberry pi handheld retro gaming console
129 parts75CERN-OHL-W-2.0 - 2 layers89 × 55.5 mm

Mintypcb
SophBG/pi-tin-mod
Personal build of jackw01's Pi Tin (3D-printed clamshell version, KiCad 10). It adds 10 RGB LEDs under the buttons, a centred speaker, a USB-drive mode for the ROMs, and ESD protection on USB, and runs on an Orange Pi…
158 parts1 - 2 layers103 × 95 mm

DSO
Aryan-Kodan/Two_Channel_DSO
A custom Multi-Channel Digital Storage Oscilloscope (DSO) designed using the STM32F103C8T6 microcontroller. This project combines a custom analog front-end, trigger circuitry, anti-alias filtering, multi-channel…
94 parts - 4 layers187 × 352.1 mm

- 2 layers95 × 75 mm

Smart Cabinet Fan
ginomcfino/smart-fan-controller
Dual-fan controller with temperature sensing, tachometer monitoring, overtemperature alarm, and manual override. Designed in KiCad.
61 parts
Questions
How big is the D Class Amp PCB?
It measures 180 × 65 mm and has 2 copper layers, 1.6 mm thick.
What parts does the D Class Amp use?
99 parts, built around the IR21834PBF, LM324, LMV393 and PHP23NQ11T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the D Class Amp KiCad files?
From the Niels-Clayton/D-Class_Amplifier repository on GitHub, at the commit this page was made from: the board is hardware/D-Class_Amp/D-Class_Amp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the D Class Amp design in my own project?
Its repository states no licence, so its author keeps all rights: ask Niels-Clayton before reusing the design.