

Esp32 vtx
- Size
- 20.1 × 39.6 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 46
- Nets
- 50
- Pads
- 193
- Tracks, vias
- 444, 134
- Pours
- 120
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 25 Feb 2023
- Updated
- 18 Nov 2024
Overview
Esp32 vtx is an open-source printed circuit board by Ncerzzk, from the Ncerzzk/esp-vtx-hardware repository on GitHub. It is a 4-layer board of 20.1 × 39.6 mm with 46 parts on 50 nets, routed with 444 tracks and 134 vias.
It is built around the ESP32-PICO-D4, MKDV4GCL-AB and AMS1117-3.3, with the XC6206-1.2V, XC6206-2.8V and BWIPX-1-001E among its other parts. Its parts include 19 capacitors, 10 resistors, 6 ICs, 2 connectors and 2 switches. It belongs with the ESP32 and RISC-V boards of this library.
Main components
6ESP32-PICO-D4
QFN-48-EP(7x7)-40℃~+85℃ -97dBm 150Mbps 2.412GHz~2.484GHz 2.4GHz 2.7V~3.6V 20dBm Bluetooth、WiFi SPI、I2C transceiver QFN-48-EP(7x7) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICsMKDV4GCL-AB
LGA-8(6x8)-25℃~+85℃ 2.7V~3.6V 4Gbit 50MHz ECC error correction function、Bad block management function SPI、SD interface Yes LGA-8(6x8) NAND FLASH ROHSMKNAND FLASHAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsXC6206-1.2V
SOT-23-3L-40℃~+125℃ 1 1.2V 400mA 6.5V Fixed Over Current Protection、Short Circuit Protection Positive SOT-23-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIUncategorisedXC6206-2.8V
SOT-23-3L-40℃~+85℃@(Ta) 1 1uA 2.8V 250mA 350mV@(30mA) 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBWIPX-1-001E
SMD-40℃~+85℃ 1 1.25mm 2mm 50Ω 6GHz Board Side IPEX Inner pin SMD Coaxial Connectors (RF) ROHSBAT WIRELESSCoaxial Connectors (RF)
README
README.mdESP VTX
基于WIFI-Broadcast原理的ESP32图传。
使用说明
天空端
地面站
- 需要一张能运行monitor模式的2.4G网卡,典型如ar9271 和 Pi(树莓派或各种国产派)
- 将ar9271插入地面站,通过ifconfig 可以看到此时多了一个网络接口
- 使用
sudo tcpdump --monitor-mode -i wlan1来测试当前系统和网卡是否支持monitor 模式,如果没有报错,且能正常dump数据,那么即为正常。注意将wlan1 换成你自己的接口名 - 编译地面站
- 编辑gs/src/main.cpp,将rx_descriptor.interfaces 和 tx_descriptor.interface 更改为你自己的接口名
- 安装依赖
sudo apt install libdrm-dev libgbm-dev libgles2-mesa-dev libpcap-dev libturbojpeg0-dev libts-dev libsdl2-dev libfreetype6-dev cd gs; make- 运行
sudo DISPLAY=:0 ./gs, 注意DISPLAY有可能是:0.0
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10K | Resistor_SMD:R_0603_1608Metric | R1, R11, R13, R15, R16, R17, R18 |
| 6 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C5, C7, C8, C12, C13 |
| 5 | 10u | Capacitor_SMD:C_0603_1608Metric | C4, C6, C17, C18, C19 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 2 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C10, C15 |
| 2 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C14, C16 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C9, C11 |
| 2 | 4K7 | Resistor_SMD:R_0603_1608Metric | R9, R14 |
| 2 | SW_SPST | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | |||
| 1 | 100uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C3 |
| 1 | 15pF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | BWIPX-1-001E | kicad_lceda:IPEX-SMD_BWIPX-1-001E | RF1 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | Conn_01x24_MountingPin | Connector_FFC-FPC:Hirose_FH12-24S-0.5SH_1x24-1MP_P0.50mm_Horizontal_larger | J1 |
| 1 | ESP32-PICO-D4 | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.3x5.3mm | U3 |
| 1 | IS25WP032 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | MKDV4GCL-AB | ic_footprint:LGA-8_L8.0-W6.0-BL_MKDV4GIL-AS | U4 |
| 1 | XC6206-1.2V | Package_TO_SOT_SMD:SOT-23 | U6 |
| 1 | XC6206-2.8V | Package_TO_SOT_SMD:SOT-23 | U5 |
Similar boards
- 4 layers48.5 × 25 mm

- 2 layers125 × 55 mm

- 4 layers80 × 40 mm

- 4 layers66 × 71 mm

- 4 layers75 × 65 mm

- 4 layers254.5 × 153.1 mm

- 4 layers29 × 52 mm

AutopilotPi AutoPilotPi Hardware AutoPilotPi
punkfab/pcb-corpus
235 real KiCad boards from open-source hardware repositories, prepared as a placement and routing benchmark
99 parts1 - 4 layers80.5 × 50 mm

Questions
How big is the Esp32 vtx PCB?
It measures 20.1 × 39.6 mm and has 4 copper layers, 4.69 mm thick.
What parts does the Esp32 vtx use?
46 parts, built around the ESP32-PICO-D4, MKDV4GCL-AB, AMS1117-3.3 and XC6206-1.2V. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32 vtx KiCad files?
From the Ncerzzk/esp-vtx-hardware repository on GitHub, at the commit this page was made from: the board is esp32_vtx.kicad_pcb and its schematic esp32_vtx.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32 vtx design in my own project?
Its repository states no licence, so its author keeps all rights: ask Ncerzzk before reusing the design.