Skip to the content
2 layers120 × 99 mmPCB 1 Multisheet Schematic, the printed circuit board in 3D

PCB 1 Multisheet Schematic

Naman-Bothra/Multisheet_Schematic_KiCAD

my first Multi sheet schematic in KiCAD

Size
120 × 99 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
33
Pads
51
Tracks, vias
79, 8
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
25 Jun 2026
Updated
25 Jun 2026

Overview

PCB 1 Multisheet Schematic is an open-source printed circuit board by Naman-Bothra, from the Naman-Bothra/Multisheet_Schematic_KiCAD repository on GitHub. It is a 2-layer board of 120 × 99 mm with 10 parts on 33 nets, routed with 79 tracks and 8 vias.

It is built around the ARDUINO UNO R3 and L7805. Its parts include 2 capacitors, 2 resistors, 2 diodes, 2 connectors and 1 IC. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

Multisheet_Schematic_KiCAD

my first Multi sheet schematic in KiCAD Custom Arduino Uno Shield with L7805 Voltage Regulation & Status Indications

A professional, multi-sheet hierarchical hardware project designed in KiCad E.D.A. 10.0.3. This project implements an Arduino Uno-compatible expansion board featuring robust linear voltage regulation (12V down to 5V), dedicated local power networks, and software-controlled LED diagnostic indicators.


🗺️ Project Architecture & Hierarchical Structure

The design follows a clean, modular multi-sheet schematic layout to maximize maintainability, isolate sub-circuits, and conform to industrial engineering standards.

text
Root (page 1)
 ├── J1 (12V Power Input Header)
 ├── J2 (5V Power Output Header)
 ├── Power (page 2)
 │    ├── Regulator (page 4): L7805 Linear Regulator Circuit
 │    └── Indications (page 5): Power & Diagnostic LED Array
 └── MCU (page 3): Arduino Uno R3 Footprint Interface

📄 Sheet Breakdown

  1. Root (Sheet 1): Serves as the top-level block design interconnecting external input/output headers (J1 for 12VIn and J2 for 5Vlocal) with sub-sheets.
  2. Power (Sheet 2): Intermediate bus routing layout connecting voltage processing directly with current-limiting diagnostic blocks.
  3. MCU Interface (Sheet 3): Bridges the system connections to the Arduino UNO R3 footprint. Features a clean, completely mapped pin configuration utilizing hierarchical labels.
  4. Regulator (Sheet 4): Houses the L7805 Linear Regulator (U1), input filtering capacitor (C1), and output smoothing capacitor (C2) alongside power-rail flags (PWR_FLAG).
  5. Indications (Sheet 5): Features current-limiting resistors (R1, R2) driving two system LEDs (D1 for constant 5V power confirmation, D2 for micro-controlled MCULed system heartbeat).

⚙️ Hardware Specifications & Net Mapping

🧩 Component Bill of Materials (BOM) Summary

DesignatorComponent NamePackage / FootprintFunctional Description
U1L7805TO-220+5V Linear Voltage Regulator
A1Arduino_UNO_R3Standard Arduino Uno R3 ShieldPrimary Processing Unit Interface
C1Capacitor (C)Surface-Mount / Through-HoleInput Decoupling & Stability Ripple Filter
C2Capacitor (C)Surface-Mount / Through-HoleOutput High-Frequency Noise Filter
R1, R2Resistor (R)SMD/SMTCurrent Limiting for Status Indicator LEDs
D1LEDStandard IndicatorConstant Power Indicator (5Vind)
D2LEDStandard IndicatorMicrocontroller Status Indicator Pin A0 (MCULed)
J1, J2Conn_01x02_Pin1x02 2.54mm Pin HeaderExternal Power & Signal Interconnect Junctions

⚡ Critical Net Rail Configurations

  • 12Vin: High-voltage input channel feeding directly into Pin 1 (IN) of the L7805 regulator.
  • 5Vop / 5Vlocal: Regulated quiet +5V output rail generated by Pin 3 (OUT) of the L7805, providing system power.
  • 5Vind: Dedicated status power bus running directly through current-limiting resistor R1 to confirm active voltage regulation.
  • MCULed: Targeted control net bound to Pin 9 (A0) of the Arduino Uno, enabling custom software-defined blink behaviors on LED D2.
  • GND: Unbroken global ground distribution network shared across all functional blocks via specialized copper planes.

🎨 PCB Layout & Manufacturing Details

The physical board layout incorporates industrial design rules configured for 2-layer fabrication layout efficiency.

  • Layer Stackup: 2-Layer Board (F.Cu Front Copper, B.Cu Bottom Copper).
  • Ground Strategy: Dual-sided solid Ground planes (GND) configured on both the top and bottom layers to drastically reduce EM noise loop areas, maximize heat dissipation for the TO-220 package, and streamline trace routing.
  • Thermal Relief Design: Set up with custom thermal relief connections (0.5mm gap clearances / 0.25mm minimum width) on all ground-plane-connected pads to prevent cold-solder structural failures during assembly.
  • Trace Optimization: Power routing features widened high-current traces to minimize impedance drops from the 12V input to the regulation circuit.

🚀 Key Implementation & KiCad Settings Verified

  • ERC Clean Workflow: Fully resolved initial reference designator conflicts (#PWR? duplicates) via programmatic schema annotations.
  • No-Net Island Prevention: Cleanly avoided floating copper traps by mapping both copper zones to the global GND net layer, stabilizing high-frequency characteristics.
  • No-Connect Cleanliness: All unused digital and analog pins on the A1 microcontroller header explicitly utilize individual No-Connect cross-markers (X) to ensure predictable system behaviors.

Parts

10
QtyValueFootprintReferences
2CCapacitor_SMD:C_1210_3225MetricC1, C2
2Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_HorizontalJ1, J2
2LEDLED_SMD:LED_0805_2012MetricD1, D2
2RResistor_SMD:R_1206_3216MetricR1, R2
1Arduino_UNO_R3Module:Arduino_UNO_R3A1
1L7805Package_TO_SOT_THT:TO-220-3_VerticalU1

Similar boards

  • 4 layers200 × 142.3 mmFRED Electrical Scheme KiCAD, the printed circuit board in 3D

    FRED Electrical Scheme KiCAD

    GiulianoAgostini04/FRED-Project

    Real-time concentration monitoring system based on frontal-lobe EEG signals. Features a custom PCB designed with TinkerCAD and KiCad, OpenBCI Ganglion and Arduino UNO for signal acquisition, display, and frequency-band…

    93 parts1MIT
  • 2 layersJONICA, the printed circuit board in 3D

    JONICA

    mhechavarria/color-caps-classifier

    A project made mostly in python to classifie color caps using OpenCV

    59 parts
  • 2 layers162.6 × 86.4 mmBms, the printed circuit board in 3D

    Bms

    akbar-q/Circuits-PCB-HardwareDesign

    The High Voltage Arc Detector is a non-contact RF-based sensing system that detects high-voltage electrical arcs.

    53 parts
  • 2 layers117.3 × 116.8 mmAssert, the printed circuit board in 3D

    Assert

    pedrodsk/pcb_cad

    Pcb projects

    24 parts
  • 2 layers68.8 × 53.6 mmRelatively Universal ROM Programmer, the printed circuit board in 3D

    Relatively Universal ROM Programmer

    AndersBNielsen/Relatively-Universal-ROM-Programmer

    Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

    149 parts257GPL-3.0
  • 2 layers69.1 × 53.8 mmMotor controller, the printed circuit board in 3D

    Motor controller

    AlanFord/self-balancing-stick

    Dual Axis Reaction Wheel Inverted Pendulum

    25 parts79MIT
  • 2 layers68.6 × 53.3 mmProtogasm Board V2, the printed circuit board in 3D

    Protogasm Board V2

    Edging-Machines/Edging-Machines

    This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.

    14 parts67MIT
  • 2 layers53.8 × 69.6 mmEVSE V2 2, the printed circuit board in 3D

    EVSE V2 2

    PedroCNeves/AC_ChargingStation

    A learning project to create an EV AC Charging station based on an Arduino Uno

    32 parts50

Questions

How big is the PCB 1 Multisheet Schematic PCB?

It measures 120 × 99 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PCB 1 Multisheet Schematic use?

10 parts, built around the ARDUINO UNO R3 and L7805. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PCB 1 Multisheet Schematic KiCad files?

From the Naman-Bothra/Multisheet_Schematic_KiCAD repository on GitHub, at the commit this page was made from: the board is PCB_1_Multisheet_Schematic.kicad_pcb and its schematic Indications.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PCB 1 Multisheet Schematic design in my own project?

Its repository states no licence, so its author keeps all rights: ask Naman-Bothra before reusing the design.