
OSO BOOK C1
joeycastillo/The-Open-Book
For details on how to build, test and use Open Book, I've made documentation available here.

Next generation hardware for the classic Osborne 1 computer. Virtual peripherals via interposer, helpful shim devices, and hopefully a faithful to history but modern recreation of the machine itself.
FloppyAdapter is an open-source printed circuit board by Myrcurial, from the Myrcurial/o1next repository on GitHub, published under the MIT licence. It is a 2-layer board of 37.3 × 45.6 mm with 38 parts on 31 nets, routed with 25 tracks and 29 vias.
The Osborne 1 uses a non-standard Shugart-like floppy interface where +12V and +5V for the drive are fed through the floppy cable. This KiCAD project accounts for that and creates a nice tidy interface to a GoTek floppy disk emulator. There is no need to modify the Osborne's floppy cable as is the case when using a generic floppy adapter.
+5V power for the GoTek is taken from the floppy cable.
Jumper only S1 on the GoTek.
GoTek part number is: SFR1M44-U100K
Connector on adapter to mate with GoTek is a Sullins PPPC172LJBN-RC
Program the GoTek with FlashFloppy firmware: https://github.com/keirf/FlashFloppy



References
Electrical Details:
3D printed 3.5" to 5.25" Floppy Case Adapter:
Richard Loxley has done a lot of good work on the Osborne 1. His site is a great resource for how to get CP/M-formatted floppy disk images working on the GoTek.
Just want the board?
Some people report that OSHPark may or may not cut the edge connector slot. So be prepared to dremmel out the slot yourself if they don't! Alternatively, it may be easier to remove the key from the floppy cable - just make sure you plug the cable into the adapter correctly or there will be smoke!
| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | GND | wayne_footprints:EdgeFinger | J1, J2, J3, J4, J5, J6, J7, J9, J19, J27, J29, J31, J33 |
| 4 | +12V | wayne_footprints:EdgeFinger | J11, J13, J15, J17 |
| 3 | +5V | wayne_footprints:EdgeFinger | J21, J23, J25 |
| 1 | 4MHz | wayne_footprints:EdgeFinger | J16 |
| 1 | Conn_01x03 | Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mm | DRV_SEL |
| 1 | Conn_02x01 | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | PWR1 |
| 1 | DIR | wayne_footprints:EdgeFinger | J18 |
| 1 | DS1 | wayne_footprints:EdgeFinger | J10 |
| 1 | DS2 | wayne_footprints:EdgeFinger | J12 |
| 1 | IDC 34 Pin | wayne_footprints:PPPC172LJBN-RC | FLOPPY |
| 1 | INDEX | wayne_footprints:EdgeFinger | J8 |
| 1 | LATE | wayne_footprints:EdgeFinger | J34 |
| 1 | NC | wayne_footprints:EdgeFinger | J14 |
| 1 | RD | wayne_footprints:EdgeFinger | J30 |
| 1 | SS | wayne_footprints:EdgeFinger | J32 |
| 1 | STEP | wayne_footprints:EdgeFinger | J20 |
| 1 | TRK00 | wayne_footprints:EdgeFinger | J26 |
| 1 | WD | wayne_footprints:EdgeFinger | J22 |
| 1 | WG | wayne_footprints:EdgeFinger | J24 |
| 1 | WP | wayne_footprints:EdgeFinger | J28 |
The 37 most common of 38 parts.

joeycastillo/The-Open-Book
For details on how to build, test and use Open Book, I've made documentation available here.


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!


Ardumower/ardumower
Develop an open source robotic lawn mower (HW+SW reference platform)

CRImier/MyKiCad
My KiCad boards. Can't be bothered uploading individually anymore, so here you go.


It measures 37.3 × 45.6 mm and has 2 copper layers, 1.6 mm thick.
38 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Myrcurial/o1next repository on GitHub, at the commit this page was made from: the board is research/osborne1/floppy-adapter/FloppyAdapter.kicad_pcb and its schematic hardware/floppy-adapter/floppy-adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).