

Esp jtag
A JTAG programmer for esp targets based on esp-prog redone in KiCad
- Size
- 50.8 × 25.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 72
- Nets
- 47
- Pads
- 253
- Tracks, vias
- 731, 75
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 22 Oct 2019
- Updated
- 23 Jul 2020
Overview
Esp jtag is an open-source printed circuit board by Muriukidavid, from the Muriukidavid/esp-jtag repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 50.8 × 25.4 mm with 72 parts on 47 nets, routed with 731 tracks and 75 vias.
It is built around the SN74AHC125RGY, 74AHC1GU04SE and AMS1117-3.3, with the FT2232HL, LESD5D5.0CT1G and LRB520S-30T1G among its other parts. Its parts include 24 capacitors, 19 resistors, 9 diodes, 5 ICs and 3 transistors. It belongs with the interfaces and adapters boards of this library.
Main components
8SN74AHC125RGY
VQFN-14-EP(3.5x3.5)-40℃~+125℃ 1 2V~5.5V 4 40uA 5.3ns@5V,50pF 74AHC 8mA 8mA Output enable Schmitt trigger Tri-State Unidirectional VQFN-14-EP(3.5x3.5) Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers74AHC1GU04SE
SOT-353-40℃~+85℃ 1 1 1.7V~4.4V 1.8V、2.7V、4V 1uA 200mV、300mV、500mV 2V~5.5V 300mV~1.1V 6mA 6mA 74AHC 7ns@5V,50pF SOT-353 Inverters ROHSDiodes IncorporatedInvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsFT2232HL
QFP64Dual High Speed USB to Multipurpose UART/FIFO ICFTDIUncategorisedLESD5D5.0CT1G
SOD-523-55℃~+150℃ 100W 12pF 16V 1uA 5V 7A 7V Bidirectional ESD IEC 61000-4-2 SOD-523 ESD and Surge Protection (TVS/ESD) ROHSGOODWORKUncategorisedLRB520S-30T1G
SOD-5231 Independent 1A 1uA@10V 200mA 30V 600mV@200mA SOD-523 Schottky Diodes ROHSLeshan Radio (LRC)Schottky DiodesS8050
SOT-23-55℃~+150℃ 1 NPN 100MHz 100nA 120 25V 300mW 500mA 5V 600mV NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)WST03P06
SOT-23-3L-55℃~+150℃ 1 P-Channel 110mΩ@10V 12pF 1W 3.5A 364pF 3V 41pF 6.3nC@4.5V 60V P-Channel SOT-23-3L MOSFETs ROHSWinsok SemiconMOSFETs
README
README.mdThis is a JTAG programmer for esp targets based on esp-prog redone in Kicad.
The goal of this repo is to enable customization by adding or removing features. Feel welcome to fork the repo and share back your customizations through a pull request.
Features:
- FT2232H based
- Esp Jtag programming
- A separate serial port for debug
- SN74AH buffers for JTAG IO pins(5V/3V torelant)
- Rx/Tx status LEDs
- Autoprogram using RTS and DTS signals
TODO
Layout the PCB and route
Add LCSC.com BOM column
- Add digikey BOM column
Schematic

Board 3D Top View
A preview of the on-going PCB layout design

3D TOP view

3D ISO view

BOM
Parts
72| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100nF/25V/10%/0402 | Capacitor_SMD:C_0402_1005Metric | C1, C3, C4, C15, C17, C18, C19, C20, C21, C22, C23, C24 |
| 9 | 10K/1%/0402 | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R5, R6, R7, R8, R10, R12 |
| 4 | 2.2K/1%/0402 | Resistor_SMD:R_0402_1005Metric | R9, R11, R18, R19 |
| 4 | 4.7uF/25V/10%/0603 | Capacitor_SMD:C_0603_1608Metric | C10, C12, C14, C16 |
| 3 | 33R/1%/0402 | Resistor_SMD:R_0402_1005Metric | R13, R14, R15 |
| 3 | LED | LED_SMD:LED_0402_1005Metric | D7, D8, D9 |
| 3 | LESD5D5.0CT1G | Diode_SMD:D_SOD-523 | D1, D2, D5 |
| 3 | bead | Inductor_SMD:L_0805_2012Metric | FB1, FB2, FB3 |
| 2 | 12pF/25V/5%/0402 | Capacitor_SMD:C_0402_1005Metric | C11, C13 |
| 2 | 1nF/25V/10%/0402 | Capacitor_SMD:C_0402_1005Metric | C6, C9 |
| 2 | 1uF/25V/10%/0402 | Capacitor_SMD:C_0402_1005Metric | C2, C7 |
| 2 | LRB520S-30T1G | Diode_SMD:D_SOD-523 | D3, D6 |
| 2 | S8050 | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 2 | SW_SPST | Button_Switch_SMD:SW_SPST_PTS810 | SW1, SW2 |
| 1 | 0/1%/0402 | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 10uF/25V/20%/0603 | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 12K/1% | Resistor_SMD:R_0402_1005Metric | R16 |
| 1 | 1K/1% | Resistor_SMD:R_0402_1005Metric | R17 |
| 1 | 22uF/10V/20%/0603 | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 3V3 | TestPoint:TestPoint_Loop_D1.80mm_Drill1.0mm_Beaded | TP2 |
| 1 | 74AHC1GU04 | Package_TO_SOT_SMD:SOT-353_SC-70-5 | U1 |
| 1 | 7M12000044 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 93CxxC | RF:SOIC-8_150mil | U4 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | BAT760-7/30V/1A/SOD-323 | Diode_SMD:D_SOD-323 | D4 |
| 1 | FT2232H | Package_QFP:LQFP-64_10x10mm_P0.5mm | U5 |
| 1 | JTAG | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J2 |
| 1 | SN74AHC125RGY | esp-jtag:VQFN-14_3.6x3.6x05P | U2 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex_47346-0001 | J1 |
| 1 | VBUS | TestPoint:TestPoint_Loop_D1.80mm_Drill1.0mm_Beaded | TP1 |
| 1 | WST03P06 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | karibe_logo | artwork:karibe_logo | L1 |
The 71 most common of 72 parts.
Similar boards
- 4 layers140 × 140 mm

- 4 layers116 × 55 mm

- 4 layers78 × 59 mm

- 4 layers74.5 × 70.3 mm

Nest mini v2-drop in pcb
iMike78/nest-mini-drop-in-pcb
Drop-in PCB replacement for the Google Nest Mini v2 with ESP32-S3, ESP32-P4 and optional ESP32-C6. Inspired by Onju Voice and Home Assistant Voice PE.
229 parts628CERN-OHL-S-2.0 - 12 layers86.4 × 54.6 mm

- 2 layers105.2 × 71.1 mm

Onyx PCB
CuriousMotor/Onyx-Stepper-Motherboard
The successor of the iconic Arduino-CNC-shield
96 parts56MIT - 4 layers145.5 × 89.6 mm

- 4 layers80.9 × 100.6 mm

Questions
How big is the Esp jtag PCB?
It measures 50.8 × 25.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp jtag use?
72 parts, built around the SN74AHC125RGY, 74AHC1GU04SE, AMS1117-3.3 and FT2232HL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp jtag KiCad files?
From the Muriukidavid/esp-jtag repository on GitHub, at the commit this page was made from: the board is esp-jtag.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp jtag design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
