
Type d
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

A breakout board to test GS+NO2 sensor
NO2 signal conditioner is an open-source printed circuit board by Muriukidavid, from the Muriukidavid/GS-NO2_sensor_breakout repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 50.8 × 27.9 mm with 14 parts on 11 nets, routed with 111 tracks and 5 vias.
It is built around the TLC2252AIP. Its parts include 5 resistors, 3 capacitors, 3 connectors, 2 ICs and 1 transistor. It belongs with the sensors and measurement boards of this library.
A breakout board to test GS+NO2 sensor
The sensor is a weak current source. This test circuit is a current to voltage converter with low power Opamps.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 1 | 0.022uF | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 12K | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 20 | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 50K | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | GS+4NO2 | Package_TO_SOT_THT:TO-8-3_Window | J1 |
| 1 | J117 | Package_TO_SOT_SMD:SOT-23_Handsoldering | Q1 |
| 1 | LM4120-AIM5-3.3/NOPB | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | TLC2252AIP | Package_DIP:DIP-8_W7.62mm | U1 |
| 1 | power | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | vout | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!



Twotoz/C5VRX
Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS


It measures 50.8 × 27.9 mm and has 2 copper layers, 1.6 mm thick.
14 parts, built around the TLC2252AIP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Muriukidavid/GS-NO2_sensor_breakout repository on GitHub, at the commit this page was made from: the board is NO2_signal_conditioner.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).