Skip to the content
2 layers94.7 × 98.7 mmLaser slot, the printed circuit board in 3D

128 Laser Extender card

Size
94.7 × 98.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
25
Nets
78
Pads
255
Tracks, vias
661, 12
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
15 Jul 2026
Updated
15 Jul 2026

Overview

Laser slot is an open-source printed circuit board by MrCrusty, from the MrCrusty/128-Laser-Extender repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 94.7 × 98.7 mm with 25 parts on 78 nets, routed with 661 tracks and 12 vias.

Its parts include 6 resistors, 6 connectors and 4 diodes.

README

README.md

FOLDER LASER_SLOT IS THE KICAD 9 VERSION OF THE PCB THAT SHOULD BE USED sorry about the other stuff not so good with using GitHub

128 Laser Extender

128 Laser Extender card

Apple_laser_extender

Screenshot 2026-07-11 135927

So here is PROBABLY ABOUT THE HUNDRETH REWORK for the 50-pin card edge connectors adapted for a 128 Laser Apple clone

My Design is provided as a Kicad 9.0 project. In the folder "extender"

The design will follow the orignal extender as far as possible. The original on line Reference Manual deals with the extender mainly as a circuit diagram and I have adopted the pinout names for my schematic and PCB design as used in the manuals schematic.

As the enclosure used for the extender will probably be 3D printed in a thermoplastic the power supply will deviate from the 10volt AC supply and linier 5V power regulator.

1. There will be the external power connector with a set of jumpers able to select both card slot supplies from either external or the Laser voltage supply or a mixture of both supplies. The original design uses +/-12V supplies from the Laser supply, +5V from an external generated source and -5V from a switch mode supply generated on the extender board from the 12V supply and +5V supply. (The orignal extender does not provide -5V from the card edge, when the extender is used, this is because the -5V line becomes a card select signal.) I recomend following the original design voltage selections or making all supplies external. I have made an option to keep the Laser +5V isolated as it would have been, link this isolator only if you are sure that Laser 5v has enough current and won't corrupt the operation of the Laser." Old style Cards are very +5V power hungry".

2.If you wish to have the original power configuration there is provision on he board for a SIP +5V isolated -5V power block, if the block is not used then if -5V is required on a plug in board then the external -5V option is required, please note the the jumper for -5V is only active when connected between card and external pins

First of all I do not own a 128 Laser clone but a member at "Applefritter" asked me if the card slot extender I had designed for the Apple ][e could be made to emulate the 128 Laser card extender made by the original designers of the 128 Laser clone.

Please note as such I will not be making a PCB, as I have no Laser clone to test it on.

The design has basicaly been a thought experiment during siesta time in the UK heatwave.

If you take the risk and get a prototype board made, I will update schematics and PCB when advised of errors.

A Design Rules (schematic) check shows errors on the card edge I have reused, as I have not changed the card edge design to suit the new outputs used by the Laser extender.

However my global circuit ID's work in the PCB and as far as I can see on a design rules check (PCB) has no errors.

More words of warning

if you stick a card in the exstension slot of the 128 Laser then you have the same pinout as any card slot of the Apple ][e and can decide if the slot is for slot 5 or slot 7 card use.

Things change when you configure the 128 laser for external card extender mode.

BEWARE the 128 Laser slot changes its pin configurations to that of a stand apple ][e slot. Almost certainly two heavy current vintage style cards pluged into an extender without isolating the 128 Laser +5V power (isolator at right of card edge connector) will probably very quickly overload the 128 Laser power supply resulting in dreaded magic grey smoke escaping from the 128 Laser.

Power is the first thing to consider in this design the orignal 128 Laser extension box was made of steel and thus could act as a heat sink for the heavy duty power draw. Also the 128 extender used an AC mains transformer to provide the raw DC supplt to the linear +5V regulator power chip.

If as it seems a 3D printed plastic box will be used for encasing the new extender pcb and cards. I do not intend to push hot power control and mains onto the card for safety reasons so power supplies will be plugable to the card. A power bank of some kind providing the correct voltages and current draw to the extender will have to be provided.

Design research with Google AI and other contributors

Google AI is helping me research the issues regarding building the extender

Google answers to my questions are in italics.

Building a custom multi-slot adapter for the Laser 128 is an excellent vintage hardware project. Because the Laser 128 routes its expansion port differently than a standard Apple IIe, you are essentially building a two-slot backplane that breaks the single 50-pin edge connector out into two physical standard Apple II slots (Slot 5 and Slot 7). 1. Configure the Laser 128 Trapdoor Switches Before designing the hardware, the Laser 128 must be configured to output both slot signals across the edge connector. Open the small plastic ROM/trapdoor hatch on the bottom of the Laser 128. Locate the physical slide configuration switches. Move the switches for Slot 5 and Slot 7 from "Internal" to "External". This instructs the internal Gate Array (U6) to stop intercepting these addresses internally and pipe the activation signals out to the side edge connector.

2. Understand Signal Routing & Device Select A standard Apple II peripheral slot expects a generic (Device Select) signal on Pin 41. Because you are driving two independent slots (5 and 7) from one ribbon cable or edge connector, you cannot blindly pass Pin 41 straight through to both slots. You must isolate them using the custom SC5XX and SC7XX lines. On your custom PCB or protoboard, route the signals according to this logic:

Laser 128 Edge ConnectorDestination on Custom Slot 5 CardDestination on Custom Slot 7 Card
Pin 27 ($\overline{DEVSEL}$)Do not connectDo not connect
SC5XX LineRoute to Pin 41 DEVSELDo not connect
SC7XX LineDo not connectRoute to Pin 41 DEVSEL
All Other Pins (1–26, 28–50)
Route directly to Slot 5 (Parallel)
Route directly to Slot 7 (Parallel)

Note: Data lines (D₀–D₇), Address lines (A₀–A₁₅), Clocks (Φ₀, 7MHz), and control lines (R/W, $\overline{RESET} are shared completely in parallel across both slots.

The Reference Manual Circuit diagram shows other change of lines but these map to card edge and sockets.

3. Account for Signal Integrity (Bus Buffering) The 65C02 CPU inside the Laser 128 is relatively low-power, and its internal address/data buffers are designed to drive the internal machine plus one external load. If you connect two modern or vintage expansion cards simultaneously, the total capacitance will degrade the digital signals, causing system crashes or graphical corruption. Buffer the Address Bus: Pass lines A₀–A₁₅ through two 74HCT244 (or 74LS244) octal buffer ICs before splitting them to the two slots. Buffer the Data Bus: Pass lines D₀–D₇ through a 74HCT245 (or 74LS245) bidirectional transceiver. Connect the direction pin (DIR) of the 74HCT245 to the R/W (Read/Write) line (Pin 18) of the Laser 128 bus to coordinate reading from or writing to the cards safely.

If the extender got away without these then they are likley only to bring in timing issues

4. Provide Isolate External Power Vintage Apple II cards (such as SCSI controllers or serial cards) pull a significant amount of current from the +5V, +12V, -5V, and -12V rails. Powering two external cards entirely off the Laser 128's internal power supply risks overheating the computer's regulator. Isolate Power Lines: Do not link the power pins (+5V, +12V) directly from the computer to the expansion slots. Add an External Power Jack: Place a standard Molex or DC barrel jack on your custom board. Use a modern, small regulated power switching module (or an old ATX supply) to supply dedicated +5V and +12V rails directly to the expansion slots. Tie Grounds Together: Ensure the Ground (GND) pins from the Laser 128 connector are securely connected to the Ground of your external power supply to keep a unified reference voltage.

5. Physical PCB Layout Tips Use a 50-pin female slot connector (or a 50-pin dual-row ribbon cable interface) to mate with the left side of the Laser 128. Source two standard 50-pin (.100" / 2.54mm pitch) card-edge connectors for the daughter slots. Keep the traces running from the Laser 128 input connector to the slots as short as possible (ideally under 15 cm / 6 inches) to prevent clock timing skew.

*Would you like me to draw up a schematic wiring diagram for the 74HCT245 data transceiver logic, or do you need help sourcing the exact part numbers

Parts

25
QtyValueFootprintReferences
4470Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR1, R2, R3, R4
4Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1, J2, J4, J5
4LEDLED_THT:LED_D3.0mmD1, D2, D3, D4
4MountingHoleMountingHole:MountingHole_2.5mm_Pad_TopBottomH1, H2, H3, H4
2150Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR5, R6
26502V3_Library:BUS_6502_v1SLOT5, SLOT7
16502V3_Library:AppleIIBus_Edge_65.70BUS1
1Jumper_2_OpenConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJP1
1Screw_Terminal_01x05TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-05P_1x05_P5.00mmJ6
1TESTConnector_PinSocket_2.54mm:PinSocket_2x25_P2.54mm_VerticalJ3
1isolated 5VDC in 5DC outConverter_DCDC:Converter_DCDC_Murata_MEE1SxxxxSC_THTPS1

More from MrCrusty/128-Laser-Extender

1
  • 2 layers94.7 × 83.2 mmBus Extender V3, the printed circuit board in 3D

    Bus Extender V3

    MrCrusty/128-Laser-Extender

    128 Laser Extender card

    12 partsCC0-1.0

Similar boards

  • 2 layers159.5 × 30 mmType f, the printed circuit board in 3D

    Type f

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    25 parts3kApache-2.0
  • 2 layers113.5 × 95.1 mmSweep high, the printed circuit board in 3D

    Sweep high

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    25 parts2.1k
  • 2 layers58.4 × 114.3 mmPicoPedal, the printed circuit board in 3D

    PicoPedal

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    25 parts915
  • 2 layers54 × 15 mmXyp gpib, the printed circuit board in 3D

    Xyp gpib

    xyphro/UsbGpib

    Versatile, cheap and portable USB to GPIB converter (USBTMC class based)

    25 parts690MIT
  • 2 layers50 × 76 mmVoron 0, the printed circuit board in 3D

    Voron 0

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    25 parts397Apache-2.0
  • 2 layers237.5 × 102.9 mmStorage, the printed circuit board in 3D

    Storage

    jes/scamp-cpu

    A homebrew 16-bit CPU with a homebrew Unix-like-ish operating system.

    25 parts301Unlicense
  • 2 layers43.3 × 21 mmNanoS3 Carrier, the printed circuit board in 3D

    NanoS3 Carrier

    UnexpectedMaker/esp32s3

    Assorted files for my ESP32-S3 development boards

    25 parts296

Questions

How big is the Laser slot PCB?

It measures 94.7 × 98.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Laser slot use?

25 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Laser slot KiCad files?

From the MrCrusty/128-Laser-Extender repository on GitHub, at the commit this page was made from: the board is Lazer/Laser_slot/Laser_slot.kicad_pcb and its schematic Lazer/Laser_slot/Laser_slot.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Laser slot design in my own project?

Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).