

BallBalancer
- Size
- 64.5 × 77 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 128
- Nets
- 79
- Pads
- 381
- Tracks, vias
- 1,002, 189
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 22 Dec 2023
- Updated
- 24 Jul 2024
Overview
BallBalancer is an open-source printed circuit board by MarcelKleiner, from the MarcelKleiner/BallBalncer repository on GitHub. It is a 2-layer board of 64.5 × 77 mm with 128 parts on 79 nets, routed with 1,002 tracks and 189 vias.
It is built around the DGD0506AFN, AP63203WU and LM2937IMP-5.0, with the USBLC6-2SC6, DMN10H220L and MM5Z3V3 among its other parts. Its parts include 36 capacitors, 26 resistors, 9 connectors, 8 ICs and 8 diodes. It belongs with the STM32 boards of this library.
Main components
6DGD0506AFN
DFN3030-10-EP-40℃~+125℃ 1.5A 12ns 17ns 2 280uA 2A 8V~14V Half-Bridge MOSFET Under Voltage Protection DFN3030-10-EP Gate Drivers ROHSDiodes IncorporatedGate DriversAP63203WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.3V 3.8V~32V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC ConvertersLM2937IMP-5.0
SOT-223-4-40℃~+85℃@(Ta) 1 10mA 150uVrms 1V@(500mA) 26V 500mA 5V Fixed Over Temperature Protection、Reverse connection protection、Short Circuit Protection Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)DMN10H220L
SOT-23-55℃~+150℃ 1 N-channel 1.3W 1.6A 100V 17pF 2.5V 250mΩ@4.5V 401pF 8.3nC@10V N-Channel SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETsMM5Z3V3
SOD-523-65℃~+150℃ 1 Independent 200mW 20uA@1V 3.1V~3.5V 3.3V 95Ω SOD-523 Zener Diodes ROHSSlkorZener Diodes
Parts
128| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C7, C10, C13, C14, C16, C18, C21, C22, C31, C32 |
| 9 | 10k | Resistor_SMD:R_0603_1608Metric | R5, R8, R11, R12, R15, R16, R17, R26, R27 |
| 8 | 22 | Resistor_SMD:R_0603_1608Metric | R18, R19, R20, R21, R22, R23, R24, R25 |
| 8 | DMN10H220L | Package_TO_SOT_SMD:TO-252-2 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 8 | IN_CH2R | TestPoint:TestPoint_Pad_D1.0mm | TP20, TP21, TP22, TP23, TP24, TP25, TP26, TP27 |
| 4 | 1000p | Capacitor_SMD:C_0805_2012Metric | C19, C20, C29, C30 |
| 4 | 10u | Capacitor_SMD:C_1210_3225Metric | C24, C25, C27, C28 |
| 4 | 1n | Capacitor_SMD:C_0603_1608Metric | C5, C6, C8, C9 |
| 4 | 1u | Capacitor_SMD:C_0603_1608Metric | C11, C12, C33, C34 |
| 4 | DGD0506A | Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm | U3, U4, U7, U8 |
| 4 | MM5Z3V3 | Diode_SMD:D_SOD-523 | D3, D4, D5, D6 |
| 3 | 330u | Capacitor_SMD:CP_Elec_8x10 | C15, C35, C36 |
| 3 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R10, R14 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric | C23, C26 |
| 2 | 240 | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 3.3k | Resistor_SMD:R_0603_1608Metric | R9, R13 |
| 2 | Motor_DC | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M1, M2 |
| 2 | SD0603 | Diode_SMD:D_0603_1608Metric | D7, D8 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C17 |
| 1 | 12V | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | 15k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 3.3V | TestPoint:TestPoint_Pad_D1.0mm | TP15 |
| 1 | 3.3u | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 5V | TestPoint:TestPoint_Pad_D1.0mm | TP14 |
| 1 | AP63203WU | Package_TO_SOT_SMD:TSOT-23-6 | U6 |
| 1 | ENCODER 1 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | ENCODER 2 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J6 |
| 1 | ENCODER1_A | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | ENCODER1_B | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | ENCODER2_A | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | ENCODER2_B | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | GH_CH1L | TestPoint:TestPoint_Pad_D1.0mm | TP10 |
| 1 | GH_CH1R | TestPoint:TestPoint_Pad_D1.0mm | TP16 |
| 1 | GH_CH2L | TestPoint:TestPoint_Pad_D1.0mm | TP12 |
| 1 | GH_CH2R | TestPoint:TestPoint_Pad_D1.0mm | TP18 |
| 1 | GL_CH1L | TestPoint:TestPoint_Pad_D1.0mm | TP11 |
| 1 | GL_CH1R | TestPoint:TestPoint_Pad_D1.0mm | TP17 |
| 1 | GL_CH2L | TestPoint:TestPoint_Pad_D1.0mm | TP13 |
| 1 | GL_CH2R | TestPoint:TestPoint_Pad_D1.0mm | TP19 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | Jack-DC | Connector_BarrelJack:BarrelJack_CUI_PJ-063AH_Horizontal | J8 |
| 1 | LED_G | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | LED_R | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LM2937IMP5 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | REF_MOT1 | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | REF_MOT2 | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | Raspberry PI UART | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Reference switch 1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | Reference switch 2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | STM32G431K8Tx | Package_QFP:LQFP-32_7x7mm_P0.8mm | U9 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J3 |
| 1 | UART_RX | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | UART_TX | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_B_Micro | Connector_USB:USB_Mini-B_Lumberg_2486_01_Horizontal | J1 |
Similar boards
- 4 layers77.6 × 30.1 mm

- 2 layers42.7 × 64 mm

DisplayController
bwilkins/DisplayControllerPCB
Controller for multiple 7-segment displays attached via shift registers
32 parts - 2 layers

- 4 layers77.6 × 30.1 mm

- 2 layers100 × 100 mm

- 4 layers140 × 90 mm

TPA3255PBTL
EliMattingly22/TPA3255_ClassD_PBTL
A KiCAD project for the TPA3255 amplifier in PBTL mode
140 parts15MIT - 2 layers65 × 68 mm

FolkraceCar2020
CASE-Association/FolkraceCar
Project for the Folkrace robot that CASE Board used in the Swedish Robotic Championship 2020
74 parts2Apache-2.0 - 2 layers100 × 60 mm

Alarming AC Enclosure
manhoosbilli1/atmega328-enclosure-tamper-alarm
ATmega328 AC enclosure tamper/intrusion alarm with LTC2960 voltage monitor, LTC4412 PowerPath, boost+buck converters
98 parts
Questions
How big is the BallBalancer PCB?
It measures 64.5 × 77 mm and has 2 copper layers, 1.6 mm thick.
What parts does the BallBalancer use?
128 parts, built around the DGD0506AFN, AP63203WU, LM2937IMP-5.0 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BallBalancer KiCad files?
From the MarcelKleiner/BallBalncer repository on GitHub, at the commit this page was made from: the board is 02_Hardware/BallBalancer/BallBalancer.kicad_pcb and its schematic 02_Hardware/BallBalancer/BallBalancer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BallBalancer design in my own project?
Its repository states no licence, so its author keeps all rights: ask MarcelKleiner before reusing the design.