Skip to the content
2 layers91.4 × 55.9 mmRegulated Power Supply, the printed circuit board in 3D

This project is a Regulated Power Supply PCB designed using KiCad. The purpose of the circuit is to convert an unregulated DC input voltage into a stable and regulated DC output voltage.

Size
91.4 × 55.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
9
Pads
43
Tracks, vias
83, 0
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
2 Oct 2026
Updated
2 Oct 2026

Overview

Regulated Power Supply is an open-source printed circuit board by Manideep136, from the Manideep136/Regulated-Power-Supply repository on GitHub. It is a 2-layer board of 91.4 × 55.9 mm with 14 parts on 9 nets, routed with 83 tracks and 0 vias.

It is built around the L7805. Its parts include 5 diodes, 3 capacitors, 2 connectors, 1 resistor and 1 IC. It belongs with the power boards of this library.

Main components

1

README

README.md

Regulated-Power-Supply

Project Overview

This project is a Regulated Power Supply PCB designed using KiCad. The purpose of the circuit is to convert an unregulated DC input voltage into a stable and regulated DC output voltage.

The PCB is designed as a beginner-friendly electronics project to understand the complete PCB design process, including schematic design, component selection, footprint assignment, PCB layout, routing, ERC/DRC checking, and 3D visualization.

🎯 Objectives Design a regulated DC power supply circuit. Convert an input DC voltage into a stable output voltage. Learn schematic design using KiCad. Select appropriate footprints for electronic components. Design and route a PCB. Perform ERC and DRC checks. Generate a 3D view of the completed PCB. Understand the complete PCB design workflow. ⚡ Working Principle

The regulated power supply works in the following stages:

DC Input An external DC voltage is supplied to the circuit through the input connector. Filtering Capacitors are used to reduce unwanted fluctuations and noise in the input voltage. Voltage Regulation A voltage regulator is used to maintain a constant output voltage even when the input voltage or load changes within the regulator's operating range. Output Filtering An additional capacitor helps stabilize the regulated output and reduce noise. DC Output The regulated voltage is available at the output connector and can be supplied to another electronic circuit. Block Diagram DC INPUT │ ▼ Input Capacitor │ ▼ Voltage Regulator │ ▼ Output Capacitor │ ▼ REGULATED DC OUTPUT 🧰 Components Used Component Quantity Purpose Voltage Regulator 1 Regulates the output voltage Input Capacitor 1 Filters input voltage Output Capacitor 1 Stabilizes output voltage Resistors As required Current limiting / indication LED 1 Power indication Input Connector 1 DC input connection Output Connector 1 Regulated output connection PCB 1 Mounting and electrical connections

Note: The exact component values depend on the schematic used for this project.

🔌 Input and Output Input

The input connector is used to provide DC power to the PCB.

INPUT +V ─────────► Regulator GND ─────────► GND Output

The regulator provides a stable DC voltage at the output connector.

OUTPUT +V_REG ──────► Load GND ──────► Load

Always verify the input voltage and regulator rating before powering the PCB.

🖥️ Software Used KiCad KiCad Schematic Editor KiCad PCB Editor KiCad 3D Viewer 🧩 KiCad Design Process

The PCB was designed using the following workflow:

  1. Schematic Design

The complete circuit was first created in KiCad Schematic Editor.

Components were placed and connected according to the circuit design.

  1. Assign Footprints

Suitable footprints were assigned to each component according to the physical components that will be used.

Examples include:

Resistor_THT Capacitor_THT Package_TO_SOT_THT Connector LED

The exact footprint should always match the physical component purchased.

  1. PCB Layout

The schematic was transferred to the PCB Editor.

Components were arranged on the PCB to obtain a compact and practical layout.

  1. Routing

Tracks were created between the components according to the schematic connections.

Power and ground paths should be given appropriate track widths according to the expected current.

  1. Design Rule Check

The PCB was checked using DRC (Design Rules Checker) to identify:

Unconnected tracks Track clearance problems Short circuits Incorrect board geometry Other PCB design-rule violations 6. 3D Visualization

KiCad's 3D Viewer was used to inspect the final PCB and verify component placement.

📁 Project Structure

A typical KiCad project contains:

Regulated-Power-Supply/ │ ├── Regulated-Power-Supply.kicad_pro ├── Regulated-Power-Supply.kicad_sch ├── Regulated-Power-Supply.kicad_pcb ├── README.md │ └── images/ ├── schematic.png ├── pcb.png └── 3d-view.png 🔍 Important PCB Design Considerations Check the polarity of capacitors. Check the polarity of LEDs. Verify regulator pin configuration. Use the correct footprint for every component. Keep power traces sufficiently wide. Maintain proper clearance between PCB tracks. Check all connector pin assignments. Run ERC before PCB layout. Run DRC after routing. Verify the PCB using the 3D Viewer before fabrication. 🧪 Testing

After assembling the PCB:

Check the PCB visually for solder bridges and incorrect components. Verify the polarity of all polarized components. Check continuity between power and ground. Apply the input voltage carefully. Measure the output voltage using a multimeter. Verify that the output remains close to the designed regulated voltage. Connect the intended load and test the circuit again. 📚 What I Learned

Through this project, I learned:

How to create a schematic in KiCad. How to select electronic components. How to assign footprints. How to transfer a schematic to PCB layout. How to place components on a PCB. How to route PCB tracks. How to use ERC and DRC. How to view a PCB in 3D. How a voltage regulator is used in a power supply circuit. Basics of designing a PCB suitable for fabrication. 🚀 Future Improvements

The project can be improved by adding:

Adjustable output voltage Multiple output voltage levels Reverse-polarity protection Over-current protection Fuse protection Power-on LED indicator Screw-terminal input/output Larger heat sink for the regulator USB output Voltage and current display ⚠️ Safety Do not exceed the maximum input voltage of the regulator. Check capacitor voltage ratings before assembly. Observe correct polarity. Do not short-circuit the output. If using a high-voltage AC source, use an appropriate isolated AC-to-DC stage and proper electrical safety practices. This PCB should not be connected directly to mains AC. 📸 Project Images

📌 Conclusion

The Regulated Power Supply PCB is a useful beginner KiCad project for understanding the complete PCB design process. It combines basic power-supply concepts with practical PCB design techniques such as schematic creation, footprint selection, component placement, routing, ERC, DRC, and 3D visualization.

This project provides a foundation for designing more advanced power supply, sensor, Arduino, ESP32, and IoT PCBs.

👨‍💻 Author

Manideep Kolluri

Project: Regulated Power Supply PCB Tool: KiCad Domain: Electronics / PCB Design

Parts

14
QtyValueFootprintReferences
41N4007Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD1, D2, D3, D4
3CCapacitor_THT:CP_Radial_D10.0mm_P2.50mm_P5.00mmC1, C2, C3
2Screw_Terminal_01x02TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_HorizontalJ1, J2
1FuseFuse:Fuseholder_Cylinder-5x20mm_Bulgin_FX0457_Horizontal_ClosedF1
1L7805Package_TO_SOT_THT:TO-220-3_VerticalU1
1LEDLED_THT:LED_D5.0mmD5
1RResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR1
1Transformer_1P_1STransformer_THT:Transformer_CHK_EI30-2VA_1xSecT1

Similar boards

  • 2 layers40.6 × 110 mmEuropi surface mount, the printed circuit board in 3D

    Europi surface mount

    Allen-Synthesis/EuroPi

    EuroPi: A reprogrammable Eurorack module based on the Raspberry Pi Pico

    92 parts584CC0-1.0
  • 2 layers132.1 × 45.7 mmIPoS, the printed circuit board in 3D

    IPoS

    peterheinrich/InternetOverSpaghetti

    Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

    42 parts342
  • 2 layers59.7 × 57.5 mmFunBox, the printed circuit board in 3D

    FunBox

    GuitarML/FunBox

    Stereo guitar pedal platform using Daisy Seed.

    61 parts289MIT
  • 2 layers90.8 × 35.6 mmERCF easy brd, the printed circuit board in 3D

    ERCF easy brd

    Tircown/ERCF-easy-brd

    More informations on how to reset for flashing:\ https://wiki.seeedstudio.com/Seeeduino-XIAO/#enter-bootloader-mode

    28 parts195GPL-3.0
  • 2 layers111.3 × 106.4 mmSuper Sixteen v1, the printed circuit board in 3D

    Super Sixteen v1

    matthewcieplak/super-sixteen

    Code and schematics for the Super Sixteen Eurorack sequencer

    141 parts171
  • 2 layers91.4 × 71.1 mmPico w rover, the printed circuit board in 3D

    Pico w rover

    NikodemBartnik/Mini-Mars-Rover

    Educational robotic platform made to look like a mini mars rover

    20 parts143MIT
  • 2 layers144.1 × 182.2 mmSHVC CPU-01, the printed circuit board in 3D

    SHVC CPU-01

    starlightk7/OpenSFC

    OSHW Reproduction Parts related to the Super Famicom / Super Nintendo game console

    498 parts114CERN-OHL-S-2.0
  • 2 layers106.1 × 155 mmMotherboard, the printed circuit board in 3D

    Motherboard

    Redherring32/OpenTendo-TopLoader

    An Open Source HardWare (OSHW) recreation of the 1993 toploading NES motherboard (Also known as NES-101)

    84 parts94

Questions

How big is the Regulated Power Supply PCB?

It measures 91.4 × 55.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Regulated Power Supply use?

14 parts, built around the L7805. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Regulated Power Supply KiCad files?

From the Manideep136/Regulated-Power-Supply repository on GitHub, at the commit this page was made from: the board is Regulated Power Supply/Regulated Power Supply.kicad_pcb and its schematic Regulated Power Supply/Regulated Power Supply.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Regulated Power Supply design in my own project?

Its repository states no licence, so its author keeps all rights: ask Manideep136 before reusing the design.